User's Manual
Table Of Contents
- Contents
- Chapter 1 Introduction
- Chapter 2 Preliminary Operations
- Chapter 3 Optimization/Calibration
- Introduction to Optimization and Calibration
- Preparing the LMF
- Overview of Packet BTS files
- LMF Features and Installation Requirements
- LMF File Structure Overview
- LMF Home Directory
- NECF Filename Conventions and Directory Location
- LMF Installation and Update Procedures
- Copy BTS and CBSC CDF (or NECF) Files to the LMF Computer
- Creating a Named HyperTerminal Connection for MMI Communication
- Span Lines - Interface and Isolation
- LMF to BTS Connection
- Using the LMF
- Pinging the Processors
- Download the BTS
- CSM System Time - GPS & LFR/HSO Verification
- Test Equipment Set-up
- Test Set Calibration
- Background
- Calibration Procedures Included
- GPIB Addresses
- Selecting Test Equipment
- Manually Selecting Test Equipment in a Serial Connection Tab
- Automatically Selecting Test Equipment in the Serial Connection Tab
- Calibrating Test Equipment
- Calibrating Cables Overview
- Calibrating Test Cabling using Communications System Analyzer
- Calibrate Test Cabling Using Signal Generator & Spectrum Analyzer
- Setting Cable Loss Values
- Setting TX Coupler Loss Value
- Bay Level Offset Calibration
- Purpose of Bay Level Offset Calibration
- What is BLO Calibration?
- Component Verification During Calibration
- When to Calibrate BLOs
- BLO Calibration Data File
- Test Equipment Setup for RF Path Calibration
- Transmit (TX) Path Calibration Description
- TX Calibration and the LMF
- TX Calibration
- All Cal/Audit and TX Calibration Procedure
- Download BLO Procedure
- Calibration Audit Introduction
- TX Path Audit
- TX Audit Test
- Create CAL File
- RFDS Set-up and Calibration
- Alarms Testing
- Chapter 4 Automated Acceptance Test Procedures
Automated Acceptance Test Procedure68P64115A18–1
Mar 2003
1X SC 4812T Lite BTS Optimization/ATP Software Release R2.16.1.x
DRAFT
4-5
S Disconnected companion frames: When inter–frame diversity RX
cables are disconnected, connect test equipment for diversity RX ATP
at the RX EXPANSION connectors 1B, 2B, or 3B on the frame under
test. Refer to Figure 4-1 and Table 4-2. Be sure EMPC is selected
before logging the LMF into the frame or FER will fail.
Figure 4-1: SC4812ET Lite Companion Frame Diversity RX Simplified Interconnection Diagram
MPC
1A
2A
3A
CIO
EMPC
INTER–FRAME
DIVERSITY RX
CABLES
1A
2A
3A
RX MAIN
(3 SECTORS)
RX DIVERSITY
(3 SECTORS)
RX MAIN
(3)
TO
BBXS
ANTENNAS
CONNECTORS
(TRDC/DRDC)
RX EXPANSION
CONNECTORS
SC4812ET LITE COMPANION FRAME 1
MPC
1A
2A
3A
CIO
EMPC
1A
2A
3A
RX MAIN
(3)
TO
BBXS
SC4812ET LITE COMPANION FRAME 2
RX EXPANSION
CONNECTORS
ANTENNAS
CONNECTORS
(TRDC/DRDC)
SC4812ETL0045–1
SIGNALS:
RX MAIN
RX DIVERSITY
NOTE: ANTENNAS connectors represent TRDC/DRDC portion of receive path.
RX DIVERSITY ATP CONNECTION POINTS:
1: For Companion Frame 1 when inter–frame diversity
RX cables are connected.
2: For Companion Frame 1 when inter–frame diversity
RX cables are disconnected.
3: For Companion Frame 2 when inter–frame diversity
RX cables are connected.
4: For Companion Frame 2 when inter–frame diversity
RX cables are disconnected.
1
2
3
4
RX EXPANSION
CONNECTORS
RX EXPANSION
CONNECTORS
3B
2B
1B
3B
2B
1B
RX MAIN
(3 SECTORS)
RX DIVERSITY
(3 SECTORS)
4