User Manual

List of Figures continued
Jan 2002
v
SC4812ET BTS Optimization/ATP CDMA LMF
Figure 3-10: Cable Calibration Test Setup Agilent E4406A/E4432B
and Advantest R3267/R3562 3-61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-11: TX Calibration Test Setup CyberTest (IS95A/B) and
Agilent 8935 (IS95A/B and CDMA2000 1X) 3-62. . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-12: TX Calibration Test Setup Using Power Meter 3-63. . . . . . . . . . . . .
Figure 3-13: TX Calibration Test Setup Agilent E4406A and
Advantest R3567 (IS95A/B and CDMA2000 1X) 3-64. . . . . . . . . . . . . . . . . . . . . .
Figure 3-14: IS95A/B Optimization/ATP Test Setup,
TRDC Shown CyberTest and Advantest R3465 3-65. . . . . . . . . . . . . . . . . . . . . . .
Figure 3-15: IS95A/B Optimization/ATP Test Setup HP 8921A 3-66. . . . . . . . .
Figure 3-16: IS95A/B and CDMA2000 1X Optimization/ATP
Test Setup With DRDCs Agilent Test Equipment 3-67. . . . . . . . . . . . . . . . . . . . . .
Figure 3-17: IS95A/B and CDMA2000 1X Optimization/ATP
Test Setup With DRDCs Advantest R3267/3562 Test Equipment 3-68. . . . . . . . .
Figure 3-18: IS95A/B and CDMA2000 1X Optimization/ATP
Test Setup With TRDCs Agilent Test Equipment 3-69. . . . . . . . . . . . . . . . . . . . . .
Figure 3-19: IS95A/B and CDMA2000 1X Optimization/ATP
Test Setup With TRDCs Advantest R3267/3562 Test Equipment 3-70. . . . . . . . .
Figure 3-20: Typical TX ATP Setup with Directional
Coupler (shown with and without RFDS) 3-71. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-21: Typical RX ATP Setup with Directional Coupler
(shown with or without RFDS) 3-72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-22: Calibrating Test Equipment Setup for TX
Cable Calibration(Using Signal Generator and Spectrum Analyzer) 3-79. . . . . . . . .
Figure 3-23: Calibrating Test Equipment Setup for RX ATP Test
(Using Signal Generator and Spectrum Analyzer) 3-80. . . . . . . . . . . . . . . . . . . . . . .
Figure 3-24: Battery Overtemperature Sensor 3-113. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-25: Location of Connector J8 on the Meter Alarm Panel 3-115. . . . . . . . . .
Figure 4-1: TX Mask Verification Spectrum Analyzer Display 4-8. . . . . . . . . . . . .
Figure 4-2: Code Domain Power and Noise Floor Levels 4-12. . . . . . . . . . . . . . . . .
Figure 5-1: MGLI2/SGLI2 MMI Port Connection 5-4. . . . . . . . . . . . . . . . . . . . . . .
Figure 6-1: CSM Front Panel Indicators & Monitor Ports 6-23. . . . . . . . . . . . . . . . .
Figure 6-2: GLI2 Front Panel Operating Indicators 6-26. . . . . . . . . . . . . . . . . . . . . .
Figure 6-3: MCC24/8E Front Panel LEDs and LED Indicators 6-28. . . . . . . . . . . .
Figure D-1: North America PCS Frequency Spectrum
(CDMA Allocation) D-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure D-2: North American Cellular Telephone System
Frequency Spectrum (CDMA Allocation). D-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure F-1: HP8921A/600 Cables Connection for 10 MHz
Signal and GPIB without Rubidium F-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure F-2: HP8921A Cables Connection for 10 MHz Signal
and GPIB with Rubidium F-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure F-3: Cable Connections for Test Set without 10 MHz
Rubidium Standard F-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . continued on next page