User's Manual
Table Of Contents
- Table of Contents
- List of Figures
- List of Tables
- Foreword
- FCC Requirements
- General Safety
- Revision History
- Patent Notification
- Chapter 1 Introduction
- Chapter 2 Preliminary Operations
- Chapter 3 Optimization/Calibration
- Optimization/Calibration - Introduction
- Isolate Span Lines/Connect LMF
- Preparing the LMF
- Using CDMA LMF
- Download the BTS
- CSM System Time/GPS and LFR/HSO Verification
- Test Equipment Set-up
- Test Set Calibration
- Bay Level Offset Calibration
- RFDS Set-up and Calibration
- BTS Redundancy/Alarm Testing
- BTS Alarms Testing
- Preliminary Operations: Overview
- Pre-Power-up Tests
- Initial Power-up Tests
- Chapter 4 Automated Acceptance Test Procedure
- Automated Acceptance Test Procedures - All-inclusive TX & RX
- TX Output Acceptance Tests: Introduction
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX Frame Error Rate (FER) Acceptance Test
- Generate an ATP Report
- Chapter 5 Prepare to Leave the Site
- Chapter 6 Basic Troubleshooting
- Basic Troubleshooting Overview
- Troubleshooting: Installation
- Troubleshooting: Download
- Troubleshooting: Calibration
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Check-list
- C-CCP Backplane Troubleshooting
- Module Front Panel LED Indicators and Connectors
- Basic Troubleshooting - Span Control Link
- Appendix A Data Sheets
- Appendix B PN Offset/I & Q Offset Register Programming Information
- Appendix C FRU Optimization/ATP Test Matrix
- Appendix D BBX Gain Set Point vs. BTS Output
- Appendix E CDMA Operating Frequency
- Appendix F PCS Interface Setup for Manual Testing
- Appendix G VSWR
- Appendix H Download ROM Code
- Appendix I In-Service Calibration
- Appendix J GPIB Addresses
- Introduction
- HP437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- Motorola CyberTest GPIB Address
- HP8935 Test Set GPIB Address
- Setting HP8921A and HP83236A/B GPIB Address
- Advantest R3465 GPIB Address
- RS232 GPIB Interface Box
- Advantest R3267 Spectrum Analyzer GPIB Address
- Agilent E4406A Transmitter Tester GPIB Address
- Index
Index
68P09255A61-4
FIELD TRIAL
Aug 2002
1X SC 4812T BTS Optimization/ATP Software Release 2.16.1.x
Index-7
Patent Notification, xxii
path
RX, 1-4
TX, 1-5
PCMCIA, Ethernet adapter, LMF to BTS connection,
3-5
Pilot Gain, 4-9, 4-10, 4-11, 4-13
Pilot Offset Acceptance test, 4-10
Pilot Time Offset, 4-6, 4-10
Pin/Signal Information for ARM A Cable, 3-104
Ping, 3-13
PN Offset
programming information, B-1
usage, B-1
PnMask, I and PnMask Q Values, B-2
Power Conversion Shelf (-48 V BTS Only), Site
Serial Number Check List, A-19
Power Delta Calibration
Advantest, I-4
HP8921A, I-2
HP8935, I-7
Power Input, 6-13
Power Meter, 1-11
illustration, J-1
Power meter
GPIB
Gigatronics 8542B, J-2
HP437B, J-1
illustration, Gigatronics 8542B, J-2
Power Meter Communication Failure,
Troubleshooting, 6-2
Power supply, converter redundancy, 3-89
Power Supply Module Interface, 6-14
power supply/converter redundancy, 3-89
Pre-power tests, test data sheets, A-3
Preliminary operations
cell Site types, 2-1
test data sheets, A-2
Prepare to Leave the Site
external test equipment removal, 5-1
LMF Removal, 5-8
re-connect BTS IFM connector, 5-3
re-connect BTS T1 spans, 5-3
Reestablish OMC-R control, 5-9
Verify T1/E1, 5-9
Pushbuttons and Connectors, GLI2, 6-23
PWR/ALM LED
BBX2, 6-26
CSM, 6-21
DC/DC Converter, 6-20
generic, 6-20
MCC, 6-26
R
RDM, 6-13
Re-connect BTS IFM connector, 5-3
Re-connect BTS T1 Spans, 5-3
Reduced ATP, 4-2, 6-8
redundancy/alarm tests, 3-88
Redundant GLIs, Enable, 3-30
Reestablish OMC-R control, 5-9
Reference Distribution Module, 6-13
Required documents, 1-14
RESET Pushbutton, GLI2, 6-23
Resetting BTS modules, 5-2
Revision History, xxi
RF
Adapters, 1-12
Attenuators, 1-12
Load, 1-12
RF Path Calibration, 3-72
RFDS
Calibration, 3-86
DC Power Pre-test, 2-11
Description, 3-80
initial power-up, 2-14
Layout, 1-35
Parameter Settings, 3-81
Set Configuration Data, 3-85
rho, 4-6