User's Manual
Table Of Contents
- Table of Contents
- List of Figures
- List of Tables
- Foreword
- FCC Requirements
- General Safety
- Revision History
- Patent Notification
- Chapter 1 Introduction
- Chapter 2 Preliminary Operations
- Chapter 3 Optimization/Calibration
- Optimization/Calibration - Introduction
- Isolate Span Lines/Connect LMF
- Preparing the LMF
- Using CDMA LMF
- Download the BTS
- CSM System Time/GPS and LFR/HSO Verification
- Test Equipment Set-up
- Test Set Calibration
- Bay Level Offset Calibration
- RFDS Set-up and Calibration
- BTS Redundancy/Alarm Testing
- BTS Alarms Testing
- Preliminary Operations: Overview
- Pre-Power-up Tests
- Initial Power-up Tests
- Chapter 4 Automated Acceptance Test Procedure
- Automated Acceptance Test Procedures - All-inclusive TX & RX
- TX Output Acceptance Tests: Introduction
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX Frame Error Rate (FER) Acceptance Test
- Generate an ATP Report
- Chapter 5 Prepare to Leave the Site
- Chapter 6 Basic Troubleshooting
- Basic Troubleshooting Overview
- Troubleshooting: Installation
- Troubleshooting: Download
- Troubleshooting: Calibration
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Check-list
- C-CCP Backplane Troubleshooting
- Module Front Panel LED Indicators and Connectors
- Basic Troubleshooting - Span Control Link
- Appendix A Data Sheets
- Appendix B PN Offset/I & Q Offset Register Programming Information
- Appendix C FRU Optimization/ATP Test Matrix
- Appendix D BBX Gain Set Point vs. BTS Output
- Appendix E CDMA Operating Frequency
- Appendix F PCS Interface Setup for Manual Testing
- Appendix G VSWR
- Appendix H Download ROM Code
- Appendix I In-Service Calibration
- Appendix J GPIB Addresses
- Introduction
- HP437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- Motorola CyberTest GPIB Address
- HP8935 Test Set GPIB Address
- Setting HP8921A and HP83236A/B GPIB Address
- Advantest R3465 GPIB Address
- RS232 GPIB Interface Box
- Advantest R3267 Spectrum Analyzer GPIB Address
- Agilent E4406A Transmitter Tester GPIB Address
- Index
Index
68P09255A61-4
1X SC 4812T BTS Optimization/ATP Software Release 2.16.1.x
FIELD TRIAL
Aug 2002
Index-4
Communications System Analyzer, 1-11
Advantest, 1-11
HP8921A/600, 1-11
CyberTest, 1-11
Connector Functionality, Backplane,
Troubleshooting, 6-13
Copy CAL files from CDMA LMF to the CBSC, 5-7
Copy CAL Files From Diskette to the CBSC, 5-8
Copy CDF Files from CBSC, 3-8
Copy Files to a Diskette, 5-7
Copy CAL files to the CBSC, 5-8
Coupler, Setting Loss Value, 3-67
CSM
Clock Source, 3-27
Enable, 3-28
frequency verification, 3-33
functions, 3-31
LEDs, 3-32
MMI terminal connection, illustration, 3-34
redundancy/alarm tests, 3-94
Reference Source Configuration Error, 6-11
Troubleshooting, 6-11, 6-12
CyberTest, 3-43
D
Data Download Failure, Troubleshooting, 6-4
DC Power Pre-test
+27 V BTS frame detail, 2-7
-48 V BTS frame detail, 2-9
BTS Frame, 2-5
RFDS, 2-11
RFDS detail, 2-11
DC Power Problems, 6-18
DC/DC Converter, LED Status Combinations, 6-20
Device Enable (INS) Failure, Troubleshooting, 6-5
Digital Control Problems, C-CCP Backplane
Troubleshooting, 6-15
Digital Multimeter, 1-11
Directional Coupler, 1-12
Distribution shelf, alarm/redundancy tests, 3-91
Download
BLO, 3-75
BTS, 3-24
BTS system software, 3-3
MGLI, 3-25
Non-MGLI2 Devices, 3-26
ROM Code, H-1
E
E1, isolate BTS from the E1 spans, 3-4
E4406A, calibration, 3-61
Enable
CSMs, 3-28
MCCs, 3-30
Redundant GLIs, 3-30
Enabling Devices, 5-2
Equipment setup, VSWR, HP Test Set, G-2
Ethernet LAN
interconnect diagram, 3-13
Transceiver, 1-9
Ethernet maintenance connector interface, illustration,
3-6
F
FER test, 4-13
Folder Structure Overview, 3-12
Foreword, xvi
Frame Error Rate, 4-6
ATP, 4-13
FREQ Monitor Connector, CSM, 6-22
Frequency counter, optional test equipment, 1-12
Frequency Spectrum
Korean PCS (1700 MHz), E-6
North American Cellular Telephone System (800
MHz), E-4
North American PCS (1900 MHz), E-1
Full Optimization, 4-2
G
Gain set point, BBX, D-1
General Safety, xix
Generating an ATP Report, 4-14
General optimization checklist, test data sheets, A-4
Gigatronics 8542B power meter, illustration, J-2