User's Manual
Table Of Contents
- Table of Contents
- List of Figures
- List of Tables
- Foreword
- FCC Requirements
- General Safety
- Revision History
- Patent Notification
- Chapter 1 Introduction
- Chapter 2 Preliminary Operations
- Chapter 3 Optimization/Calibration
- Optimization/Calibration - Introduction
- Isolate Span Lines/Connect LMF
- Preparing the LMF
- Using CDMA LMF
- Download the BTS
- CSM System Time/GPS and LFR/HSO Verification
- Test Equipment Set-up
- Test Set Calibration
- Bay Level Offset Calibration
- RFDS Set-up and Calibration
- BTS Redundancy/Alarm Testing
- BTS Alarms Testing
- Preliminary Operations: Overview
- Pre-Power-up Tests
- Initial Power-up Tests
- Chapter 4 Automated Acceptance Test Procedure
- Automated Acceptance Test Procedures - All-inclusive TX & RX
- TX Output Acceptance Tests: Introduction
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX Frame Error Rate (FER) Acceptance Test
- Generate an ATP Report
- Chapter 5 Prepare to Leave the Site
- Chapter 6 Basic Troubleshooting
- Basic Troubleshooting Overview
- Troubleshooting: Installation
- Troubleshooting: Download
- Troubleshooting: Calibration
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Check-list
- C-CCP Backplane Troubleshooting
- Module Front Panel LED Indicators and Connectors
- Basic Troubleshooting - Span Control Link
- Appendix A Data Sheets
- Appendix B PN Offset/I & Q Offset Register Programming Information
- Appendix C FRU Optimization/ATP Test Matrix
- Appendix D BBX Gain Set Point vs. BTS Output
- Appendix E CDMA Operating Frequency
- Appendix F PCS Interface Setup for Manual Testing
- Appendix G VSWR
- Appendix H Download ROM Code
- Appendix I In-Service Calibration
- Appendix J GPIB Addresses
- Introduction
- HP437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- Motorola CyberTest GPIB Address
- HP8935 Test Set GPIB Address
- Setting HP8921A and HP83236A/B GPIB Address
- Advantest R3465 GPIB Address
- RS232 GPIB Interface Box
- Advantest R3267 Spectrum Analyzer GPIB Address
- Agilent E4406A Transmitter Tester GPIB Address
- Index
Index
68P09255A61-4
FIELD TRIAL
Aug 2002
1X SC 4812T BTS Optimization/ATP Software Release 2.16.1.x
Index-3
C-CCP Shelf, 1-21
Site Serial Number Check List, A-18
Cable
GPIB, 1-11
LAN Cable, 1-12
Calibrating, 3-47, 3-62
Null Modem, 3-33
Setting Loss Values, 3-66
Timimg Reference, 1-11
Cable Calibration
HP8921 with HP PCS
Interface (HP83236), F-3
Manual, F-3
CAL File, 3-79
Calculating Center Frequencies
1700 MHz, E-7
1900 MHz, E-2
800 MHz, E-4
Calibrating
Cables, 3-62
RX, 3-64
TX, 3-63
Test Equipment, 3-60
Calibrating Test Cable, Advantest R3465, F-8
Calibration
BLO, 3-68
Cable, 1-8
data file, BLO, 3-69
In-Service, I-15
RF Path, Test Equipment Setup, 3-72
RFDS, 3-86
Test Equipment, 1-8
TX Path, 3-69, 3-72
Test Cable Calibration, 1-8
Test Equipment Calibration, 1-8
Calibration Audit Failure, Troubleshooting, 6-7
Cannot communicate to Communications Analyzer,
6-3
Cannot communicate to Power Meter, 6-2
Cannot download CODE to any device card, 6-4
Cannot Download DATA to any device card, 6-4
Cannot ENABLE device, 6-5
Cannot load BLO, 6-7
Cannot Log into cell-site, 6-2
Cannot perform carrier measurement, 6-9
Cannot perform Code Domain Noise Power
measurement, 6-9
Cannot perform Rho or pilot time offset
measurement, 6-8
Cannot perform Txmask measurement, 6-8
Carrier Measurement Failure, Troubleshooting, 6-9
CDF
site configuration, 3-2
site equipage verification, 3-3
site type and equipage data information, 2-1
CDF Files, Copy from CBSC, 3-8
CDI Alarm
with Alarms Test Box, 3-101
without Alarms Test Box, 3-103
CDMA LMF, Product Description, 1-3
Cell Site
equipage verification, 2-1
preliminary operations, 2-1
types, 3-2
Cell Site Data File. See CDF
Channel elements, No or missing, 6-17
Channels
1700 MHz, E-6
1900 MHz, E-1
800 MHz, E-4
Checksum Failure, 6-11
CIO, Connectors, 6-14
CLI, 1-3, 3-17
Command Line Interface, 3-16
Format Conventions, 3-17
Logging Out, 3-22
Cobra RFDS
external housing, 1-35
RF connector panel detail, 1-35
Code Domain Power, 4-6
ATP, 4-11
Code Domain Power and Noise Floor Measurement
Failure, Troubleshooting, 6-9
Code Domain Power Test, 4-11
Code Download Failure, Troubleshooting, 6-4
Command Line Interface, 1-3, 3-17
Common power supply verification, 2-13
Communications Analyzer Communication Failure,
Troubleshooting, 6-3