User's Manual
Table Of Contents
- Table of Contents
- List of Figures
- List of Tables
- Foreword
- FCC Requirements
- General Safety
- Revision History
- Patent Notification
- Chapter 1 Introduction
- Chapter 2 Preliminary Operations
- Chapter 3 Optimization/Calibration
- Optimization/Calibration - Introduction
- Isolate Span Lines/Connect LMF
- Preparing the LMF
- Using CDMA LMF
- Download the BTS
- CSM System Time/GPS and LFR/HSO Verification
- Test Equipment Set-up
- Test Set Calibration
- Bay Level Offset Calibration
- RFDS Set-up and Calibration
- BTS Redundancy/Alarm Testing
- BTS Alarms Testing
- Preliminary Operations: Overview
- Pre-Power-up Tests
- Initial Power-up Tests
- Chapter 4 Automated Acceptance Test Procedure
- Automated Acceptance Test Procedures - All-inclusive TX & RX
- TX Output Acceptance Tests: Introduction
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX Frame Error Rate (FER) Acceptance Test
- Generate an ATP Report
- Chapter 5 Prepare to Leave the Site
- Chapter 6 Basic Troubleshooting
- Basic Troubleshooting Overview
- Troubleshooting: Installation
- Troubleshooting: Download
- Troubleshooting: Calibration
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Check-list
- C-CCP Backplane Troubleshooting
- Module Front Panel LED Indicators and Connectors
- Basic Troubleshooting - Span Control Link
- Appendix A Data Sheets
- Appendix B PN Offset/I & Q Offset Register Programming Information
- Appendix C FRU Optimization/ATP Test Matrix
- Appendix D BBX Gain Set Point vs. BTS Output
- Appendix E CDMA Operating Frequency
- Appendix F PCS Interface Setup for Manual Testing
- Appendix G VSWR
- Appendix H Download ROM Code
- Appendix I In-Service Calibration
- Appendix J GPIB Addresses
- Introduction
- HP437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- Motorola CyberTest GPIB Address
- HP8935 Test Set GPIB Address
- Setting HP8921A and HP83236A/B GPIB Address
- Advantest R3465 GPIB Address
- RS232 GPIB Interface Box
- Advantest R3267 Spectrum Analyzer GPIB Address
- Agilent E4406A Transmitter Tester GPIB Address
- Index
Optimization (Pre-ATP) Data Sheets68P09255A61-4
Aug 2002
1X SC 4812T BTS Optimization/ATP Software Release 2.16.1.x
FIELD TRIAL
A-13
Table A-12: TX BLO Calibration (3-S: 3- or 4-C Adjacent Channels)
OK CommentsSpecificationParameter
BBX-7, ANT-1 = dB
BBX-r, ANT-1 = dB
Calibrate
carrier 2
TX Bay Level Offset = 42 dB (+4 dB)
prior to calibration
BBX-8, ANT-2 = dB
BBX-r, ANT-2 = dB
BBX-9, ANT-3 = dB
BBX-r, ANT-3 = dB
BBX-4, ANT-4 = dB
BBX-r, ANT-4 = dB
Calibrate
carrier 3
TX Bay Level Offset = 42 dB (+4 dB)
prior to calibration
BBX-5, ANT-5 = dB
BBX-r, ANT-5 = dB
BBX-6, ANT-6 = dB
BBX-r, ANT-6 = dB
BBX-10, ANT-4 = dB
BBX-3, ANT-4 = dB
Calibrate
carrier 4
TX Bay Level Offset = 42 dB (+4 dB)
prior to calibration
BBX-11, ANT-5 = dB
BBX-r, ANT-5 = dB
BBX-12, ANT-6 = dB
BBX-r, ANT-6 = dB
BBX-1, ANT-1 = dB
BBX-r, ANT-1 = dB
Calibration
Audit
carrier 1
0 dB (+0.5 dB) for gain set resolution
post calibration
BBX-2, ANT-2 = dB
BBX-r, ANT-2 = dB
carrier 1
BBX-3, ANT-3 = dB
BBX-r, ANT-3 = dB
BBX-7, ANT-1 = dB
BBX-r, ANT-1 = dB
Calibration
Audit
carrier 2
0 dB (+0.5 dB) for gain set resolution
post calibration
BBX-8, ANT-2 = dB
BBX-r, ANT-2 = dB
carrier 2
BBX-9, ANT-3 = dB
BBX-r, ANT-3 = dB
. . . continued on next page
A