User's Manual

ManualsBrandsNokia Solutions and Networks ManualsElectronics-48V SC4812T 800 MHz CDMA BTS Frame

Table Of Contents

Table of Contents
List of Figures
List of Tables
Foreword
FCC Requirements
General Safety
Revision History
Patent Notification
Chapter 1 Introduction
- Optimization Manual: Scope and Layout
- Purpose of the Optimization
- Abbreviations and Acronyms
- Required Test Equipment
- Required Documentation
- BTS Equipment Identification
- BTS Frame Description
- Frame Module Location & Identification
- Sector Configuration
Chapter 2 Preliminary Operations
- Chapter 3 Optimization/Calibration
- Optimization/Calibration - Introduction
- Isolate Span Lines/Connect LMF
- Preparing the LMF
- Using CDMA LMF
- Download the BTS
- CSM System Time/GPS and LFR/HSO Verification
- Test Equipment Set-up
- Test Set Calibration
- Bay Level Offset Calibration
- RFDS Set-up and Calibration
- BTS Redundancy/Alarm Testing
- BTS Alarms Testing
- Preliminary Operations: Overview
- Pre-Power-up Tests
- Initial Power-up Tests
Chapter 4 Automated Acceptance Test Procedure
- Automated Acceptance Test Procedures - All-inclusive TX & RX
- TX Output Acceptance Tests: Introduction
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX Frame Error Rate (FER) Acceptance Test
- Generate an ATP Report
Chapter 5 Prepare to Leave the Site
- External Test Equipment Removal
- Reset All Devices
- Re-connect BTS T1 Spans and Integrated Frame Modem
- BTS Site Span Configuration Verification
- Set BTS Site Span Configuration
- Updating CBSC LMF Files
- LMF Removal
- Re-establish OMC-R Control/ Verifying T1/E1
Chapter 6 Basic Troubleshooting
- Basic Troubleshooting Overview
- Troubleshooting: Installation
- Troubleshooting: Download
- Troubleshooting: Calibration
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Check-list
- C-CCP Backplane Troubleshooting
- Module Front Panel LED Indicators and Connectors
- Basic Troubleshooting - Span Control Link
Appendix A Data Sheets
- Optimization (Pre-ATP) Data Sheets
- Site Serial Number Check List
Appendix B PN Offset/I & Q Offset Register Programming Information
Appendix C FRU Optimization/ATP Test Matrix
Appendix D BBX Gain Set Point vs. BTS Output
Appendix E CDMA Operating Frequency
Appendix F PCS Interface Setup for Manual Testing
- Purpose
- Equipment Warm up
- Prerequisites
- HP8921A System Connectivity Test
- Manual Cable Calibration using HP8921 with HP PCS Interface (HP83236)
- HP PCS Interface Test Equipment Setup for Manual Testing
- Calibrating Test Cable Setup using Advantest R3465
Appendix G VSWR
Appendix H Download ROM Code
Appendix I In-Service Calibration
- Introduction
- Power Delta Calibration
- In-Service Calibration
Appendix J GPIB Addresses
Introduction
HP437 Power Meter GPIB Address
Gigatronics 8541C Power Meter GPIB Address
Motorola CyberTest GPIB Address
HP8935 Test Set GPIB Address
Setting HP8921A and HP83236A/B GPIB Address
Advantest R3465 GPIB Address
RS232 GPIB Interface Box
Advantest R3267 Spectrum Analyzer GPIB Address
Agilent E4406A Transmitter Tester GPIB Address
Index

General Safety

68P09255A61-4

1X SC 4812T BTS Optimization/ATP Software Release 2.16.1.x

FIELD TRIAL

xxii

Aug 2002

Dangerous procedure

warnings

Warnings, such as the example below, precede potentially dangerous

procedures throughout this manual. Instructions contained in the

warnings must be followed. You should also employ all other safety

precautions that you deem necessary for the operation of the equipment

in your operating environment.

WARNING Dangerous voltages, capable of causing death, are present in this

equipment. Use extreme caution when handling, testing, and

adjusting.