User's Manual
Table Of Contents
- Table of Contents
- List of Figures
- List of Tables
- Foreword
- FCC Requirements
- General Safety
- Revision History
- Patent Notification
- Chapter 1 Introduction
- Chapter 2 Preliminary Operations
- Chapter 3 Optimization/Calibration
- Optimization/Calibration - Introduction
- Isolate Span Lines/Connect LMF
- Preparing the LMF
- Using CDMA LMF
- Download the BTS
- CSM System Time/GPS and LFR/HSO Verification
- Test Equipment Set-up
- Test Set Calibration
- Bay Level Offset Calibration
- RFDS Set-up and Calibration
- BTS Redundancy/Alarm Testing
- BTS Alarms Testing
- Preliminary Operations: Overview
- Pre-Power-up Tests
- Initial Power-up Tests
- Chapter 4 Automated Acceptance Test Procedure
- Automated Acceptance Test Procedures - All-inclusive TX & RX
- TX Output Acceptance Tests: Introduction
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX Frame Error Rate (FER) Acceptance Test
- Generate an ATP Report
- Chapter 5 Prepare to Leave the Site
- Chapter 6 Basic Troubleshooting
- Basic Troubleshooting Overview
- Troubleshooting: Installation
- Troubleshooting: Download
- Troubleshooting: Calibration
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Check-list
- C-CCP Backplane Troubleshooting
- Module Front Panel LED Indicators and Connectors
- Basic Troubleshooting - Span Control Link
- Appendix A Data Sheets
- Appendix B PN Offset/I & Q Offset Register Programming Information
- Appendix C FRU Optimization/ATP Test Matrix
- Appendix D BBX Gain Set Point vs. BTS Output
- Appendix E CDMA Operating Frequency
- Appendix F PCS Interface Setup for Manual Testing
- Appendix G VSWR
- Appendix H Download ROM Code
- Appendix I In-Service Calibration
- Appendix J GPIB Addresses
- Introduction
- HP437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- Motorola CyberTest GPIB Address
- HP8935 Test Set GPIB Address
- Setting HP8921A and HP83236A/B GPIB Address
- Advantest R3465 GPIB Address
- RS232 GPIB Interface Box
- Advantest R3267 Spectrum Analyzer GPIB Address
- Agilent E4406A Transmitter Tester GPIB Address
- Index
BTS Redundancy/Alarm Testing
68P09255A61-4
Aug 2002
1X SC 4812T BTS Optimization/ATP Software Release 2.16.1.x
FIELD TRIAL
3-92
Table 3-49: Power Supply/Converter Redundancy (BTS Frame)
ActionStep
NOTE
For +27 V systems, skip to step 7 through step 10.
7 On -48 V systems, remove PS-4 (see Figure 3-23).
- Observe that an alarm message is reported via the MGLI as displayed on the alarm monitor.
- Verify no other modules went OOS.
8 Re-install PS-4.
Observe the alarm clears on the alarm monitor.
9 Repeat steps 7 and 8 for PS-5 through PS-9.
10 Verify that all PWR/ALM LEDs are GREEN.
11 Select BBX-1 and Device>BBX/MAWI>Dekey
Figure 3-22: SC 4812T C-CCP Shelf
ÂÂÂÂÂÂ
ÂÂÂÂÂÂ
ÂÂÂÂÂÂ
ÂÂÂÂÂÂ
ÂÂÂÂÂÂ
Á
Á
Á
Á
Á
Á
Á
Á
Á
19 mm Filler Panel
PS-3
AMR-1
CSM-1
CSM-2
38 mm Filler Panel
AMR-2
GLI2-1GLI2-2
MCC-6
BBX2-1
BBX-2
BBX-3
BBX-4
BBX-5
BBX-6
BBX-RSwitch
MPC/EMPC-1MPC/EMPC-2
CIO
BBX-7
BBX-8
BBX-9
BBX-10
BBX-1 1
BBX-12
MCC-5
MCC-4
MCC-3
MCC-2
MCC-1
MCC-12
MCC-11
MCC-10
MCC-9
MCC-8
MCC-7
PS-2
PS-1
CCD-2 CCD-1
NOTE: MCCs may be
MCC8Es, MCC24s, or
MCC-1Xs. BBXs may
be BBX2s or BBX-1Xs.
GLIs may be GLI2s or
GLI3s.
HSO/LFR
FW00295
3