User's Manual

List of Tables – continued
DRAFT
SC300 1X BTS Hardware Installation, ATP, and FRU Procedures
JAN 2002
xiv
Table 7-10: Procedure to Verify and Change BTS Sync Mode 7-27. . . . . . . . . . . . .
Table 7-11: Procedure to Verify DPLL Tracking 7-28. . . . . . . . . . . . . . . . . . . . . . . .
Table 7-12: Procedure to Verify Default Startup Coordinates 7-29. . . . . . . . . . . . . .
Table 7-13: Procedure to Set Frame ID for
Multi–Unit Logical BTS Configuration 7-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7-14: Procedure to Create Site–Specific BTS Directory 7-32. . . . . . . . . . . . .
Table 7-15: Procedure to Start the LMF and Login to the BTS 7-33. . . . . . . . . . . .
Table 7-16: Procedure to Update BTS–Specific CDF File Device Load Version 7-33
Table 7-17: Procedure to Download/Enable MAWI 7-34. . . . . . . . . . . . . . . . . . . . . .
Table 7-18: System Status LED States 7-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7-19: Procedure to Verify and Set Span Line Settings 7-37. . . . . . . . . . . . . . .
Table 7-20: SPAN_CONFIG Command Parameters 7-39. . . . . . . . . . . . . . . . . . . . .
Table 7-21: Verify and/or Change Gigatronics 8541C Power Meter GPIB
Address 7-40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7-22: Verify and/or Change Motorola CyberTest GPIB Address 7-41. . . . . . .
Table 7-23: Verify and/or Change HP8935 GPIB Address 7-42. . . . . . . . . . . . . . . .
Table 7-24: Verify and/or Change HP8921A and HP83236A GPIB Addresses 7-43
Table 7-25: Verify and/or Change Advantest R3465 GPIB Address 7-44. . . . . . . . .
Table 7-26: Verify and Change Advantest R3267 GPIB Address 7-45. . . . . . . . . . .
Table 7-27: Verify and Change Agilent E4406A GPIB Address 7-47. . . . . . . . . . . .
Table 7-28: Verify and Change Agilent E4432B GPIB Address 7-49. . . . . . . . . . . .
Table 7-29: Procedure to Calibrate Test Equipment 7-52. . . . . . . . . . . . . . . . . . . . . .
Table 7-30: Procedure to Calibrate R3465 7-53. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7-31: Procedure to Calibrate R3267 7-53. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7-32: Perform Agilent E4406A Self–alignment (Calibration) 7-54. . . . . . . . .
Table 7-33: Procedure to Setup Advantest R3465 Test Equipment 7-55. . . . . . . . .
Table 7-34: Procedure to Setup Advantest R3267 Test Equipment 7-56. . . . . . . . .
Table 7-35: Procedure to Select Test Equipment 7-57. . . . . . . . . . . . . . . . . . . . . . . .
Table 7-36: Procedure to Manually Select Test Equipment in a
Serial Connection Tab 7-58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7-37: Procedure to Select Test Equipment Using Auto-Detect 7-59. . . . . . . .
Table 7-38: Procedure to Calibrate the Power Meter 7-60. . . . . . . . . . . . . . . . . . . . .
Table 7-39: Automated Cable Calibration 7-62. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7-40: Procedure to Create a CAL File 7-66. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7-41: Procedure to Test and Verify the Subscriber Unit 7-69. . . . . . . . . . . . . .
Table 7-42: Procedure to Program the SU NAM Parameters 7-71. . . . . . . . . . . . . . .
Table 7-43: 1900 MHz TX and RX Frequency vs. Channel 7-74. . . . . . . . . . . . . . .
Table 7-44: 800 MHz TX and RX Frequency vs. Channel 7-76. . . . . . . . . . . . . . . .