User's Manual

List of Tables – continued
DRAFT
SC300 1X BTS Hardware Installation, ATP, and FRU Procedures
JAN 2002
xii
Table 5-7: Procedure to Install the AC Input Cable(s) on a
BTS Equipped with Optional Primary Surge Suppressor 5-11. . . . . . . . . . . . . . . . .
Table 5-8: Procedure to Install the DC Input Cable(s) on a
BTS Equipped with Optional Primary Surge Suppressor 5-11. . . . . . . . . . . . . . . . .
Table 5-9: Required Cables for Antenna Connections 5-13. . . . . . . . . . . . . . . . . . . .
Table 5-10: Pin and Signal Information for Cables C and D (Antenna Cable) 5-13.
Table 5-11: Procedure to Install Antenna Cabling for Sites Equipped with
Primary Surge Suppressor 5-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 5-12: Required Cables for Antenna Connections 5-17. . . . . . . . . . . . . . . . . . .
Table 5-13: Procedure to Install Site I/O Cable Between Site I/O Junction Box
and Optional Primary Surge Suppressor 5-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 5-14: Pin/Signal Information for Site I/O Cable and Punchdown Block 5-20.
Table 5-15: Customer Alarm Wiring Positions in AC Load Center on MOVs 5-22.
Table 5-16: Connecting the RGPS to the Site I/O Cable 5-23. . . . . . . . . . . . . . . . . .
Table 5-17: Required Cables for Multi–BTS RGPS Cabling 5-24. . . . . . . . . . . . . . .
Table 5-18: RGPS Synchronization Cable Kit – SGKN4351A 5-24. . . . . . . . . . . .
Table 5-19: RGPS Synchronization Cable Kit – SGKN4352A 5-24. . . . . . . . . . . .
Table 5-20: Procedure to Install RGPS Cabling for an Indoor Installation 5-25. . . .
Table 5-21: Procedure to Install RGPS Cabling for an Outdoor Installation 5-26. . .
Table 5-22: Twisted Pairs for RGPS Sync Cable (Cable X) 5-28. . . . . . . . . . . . . . .
Table 5-23: Multi–BTS RGPS Cable Run List for Primary Surge Suppressor 5-29.
Table 5-24: Required Cables for Span Line Daisy Chain Cabling 5-32. . . . . . . . . . .
Table 5-25: Cable Run List for Span Line Daisy Chain Cabling 5-33. . . . . . . . . . . .
Table 6-1: Procedure to Install Back Fin Cover to Unit 6-5. . . . . . . . . . . . . . . . . . .
Table 6-2: Installation Handle Kit 6-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 6-3: Procedure to Attach the Installation Handles 6-6. . . . . . . . . . . . . . . . . .
Table 6-4: Procedure to Attach the Unit to the Mounting Bracket 6-8. . . . . . . . . . .
Table 6-5: Required Cables for Earth Ground Cabling 6-10. . . . . . . . . . . . . . . . . . .
Table 6-6: Procedure to Attach the Earth Ground Cables 6-10. . . . . . . . . . . . . . . . .
Table 6-7: Procedure to Attach the Site I/O Junction Box to the Unit 6-13. . . . . . . .
Table 6-8: Procedure to Attach a Site I/O Cap to the Unit (optional) 6-14. . . . . . . .
Table 6-9: External Subscriber Unit Kit – T529AA 6-15. . . . . . . . . . . . . . . . . . . . . .
Table 6-10: Terminations of Unused Connectors 6-15. . . . . . . . . . . . . . . . . . . . . . . .
Table 6-11: Procedure to Install the SU Box 6-16. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 6-12: Procedure to Install the SU Cabling 6-17. . . . . . . . . . . . . . . . . . . . . . . .
Table 6-13: Procedure to Attach the Front Fin Cover to Unit 6-18. . . . . . . . . . . . . .
Table 6-14: Procedure to Attach the Short Duration Battery to the Unit 6-19. . . . . .
Table 6-15: Procedure to Install Short Duration Battery Cable to Unit 6-21. . . . . . .