User's Manual

List of Figures – continued
May 2000
v
SC 4812T CDMA BTS Optimization/ATP
Figure 3-6: +27 V SC 4812T Starter Frame I/O Plate 3-17. . . . . . . . . . . . . . . . . . . .
Figure 3-7: –48 V SC 4812T Starter Frame I/O Plate 3-18. . . . . . . . . . . . . . . . . . . .
Figure 3-8: Null Modem Cable Detail 3-30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-9: CSM MMI terminal connection 3-31. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-10: Cable Calibration Test Setup 3-42. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-11: TX Calibration Test Setup (CyberTest, HP 8935, and Advantest) 3-43
Figure 3-12: TX Calibration Test Setup HP 8921A W/PCS for 1.7/1.9 GHz 3-44. .
Figure 3-13: Optimization/ATP Test Setup Calibration (CyberTest,
HP 8935 and Advantest) 3-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-14: Optimization/ATP Test Setup HP 8921A 3-46. . . . . . . . . . . . . . . . . . .
Figure 3-15: Typical TX ATP Setup with Directional Coupler (shown
with and without RFDS) 3-47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-16: Typical RX ATP Setup with Directional Coupler (shown
with or without RFDS) 3-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-17: Calibrating Test Equipment Setup for TX BLO and TX ATP
Tests (using Signal Generator and Spectrum Analyzer) 3-55. . . . . . . . . . . . . . . . . . .
Figure 3-18: Calibrating Test Equipment Setup for RX ATP Test
(using Signal Generator and Spectrum Analyzer) 3-56. . . . . . . . . . . . . . . . . . . . . . .
Figure 3-19: Alarm Connector Location and Connector Pin Numbering 3-81. . . . .
Figure 3-20: AMR Connector Pin Numbering 3-82. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-1: TX Mask Verification Spectrum Analyzer Display 4-7. . . . . . . . . . . . .
Figure 4-2: Code Domain Power and Noise Floor Levels 4-11. . . . . . . . . . . . . . . . .
Figure 5-1: MGLI2/SGLI2 MMI Port Connection 5-4. . . . . . . . . . . . . . . . . . . . . . .
Figure 5-2: Site and Span I/O Boards T1 Span Connections 5-8. . . . . . . . . . . . . . .
Figure 6-1: CSM Front Panel Indicators & Monitor Ports 6-21. . . . . . . . . . . . . . . . .
Figure 6-2: GLI2 Front Panel 6-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-3: MCC24/8E Front Panel 6-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure E-1: North American PCS 1900 MHz Frequency Spectrum
(CDMA Allocation) E-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure E-2: North American Cellular Telephone System Frequency
Spectrum (CDMA Allocation) E-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure E-3: 1700 MHz PCS Frequency Spectrum (CDMA Allocation) E-6. . . . . .
Figure F-1: Calibrating Test Setup Components F-6. . . . . . . . . . . . . . . . . . . . . . . .
Figure F-2: Cable Calibration using Advantest R3465 F-10. . . . . . . . . . . . . . . . . . .
Figure G-1: Manual VSWR Test Setup Using HP8921 Test Set
(1700/1900 MHz) G-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure G-2: Manual VSWR Test Setup Using HP8921 Test Set (800 MHz) G-4. .
Figure G-3: Manual VSWR Test Setup Using Advantest R3465 G-6. . . . . . . . . . .