Installation Instructions

List of Tables – continued

DEC 2000

SCt300 BTS Hardware Installation, ATP and FRU Procedures

PRELIMINARY

Table 6-47: Procedure to Power on the Surge Suppressor, the Unit, and

Mount the Solar Cover 6-53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 6-47: Installation Completion Checklist 6-58. . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-1: Procedure for Removing Diagnostic Access Cover 7-5. . . . . . . . . . . . .

Table 7-2: 15–Pin MMI/LMF Serial Cable Information 7-8. . . . . . . . . . . . . . . . . .

Table 7-3: Interfacing test equipment to the BTS 7-9. . . . . . . . . . . . . . . . . . . . . . . .

Table 7-4: Connect the Communication Test Set and Power Meter to the LMF 7-13

Table 7-5: Create a HyperTerminal Connection 7-15. . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-6: Establishing MMI Communication 7-17. . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-7: Updating Default Channel Setting to Customer Operating Channel 7-18

Table 7-8: Verify BTS Sync Mode 7-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-9: Verify DPLL Tracking 7-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-10: Verify Default Startup Coordinates 7-22. . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-11: Create Site–Specific BTS Directory 7-24. . . . . . . . . . . . . . . . . . . . . . . .

Table 7-12: Start the LMF and Login to the BTS 7-25. . . . . . . . . . . . . . . . . . . . . . .

Table 7-13: Update BTS Specific CDF File Device Load Version 7-26. . . . . . . . . .

Table 7-14: Download/Enable MAWI 7-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-15: System Status LED States 7-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-16: Selecting Test Equipment Manually in a Serial Connection Tab 7-30. .

Table 7-17: Selecting Test Equipment Using Auto-Detect 7-31. . . . . . . . . . . . . . . . .

Table 7-18: Test Equipment Calibration 7-32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-19: R3465 Calibration Procedure 7-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-20: Gigatronics Power Meter GPIB Address Procedure 7-35. . . . . . . . . . . .

Table 7-21: Test Equipment Setup 7-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-22: Test Equipment Selection 7-37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-23: Calibrate the Power Meter 7-38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-24: Automated Cable Calibration 7-40. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-25: Create CAL File 7-43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-26: RF Path Audit 7-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-27: 1900 MHz TX and RX Frequency vs. Channel 7-49. . . . . . . . . . . . . . .

Table 7-28: 800 MHz TX and RX Frequency vs. Channel 7-51. . . . . . . . . . . . . . . .

Table 7-29: TX Acceptance Test Outline 7-53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-30: TX Test Using Backup Synchronization 7-53. . . . . . . . . . . . . . . . . . . . .

Table 7-31: RX ATP Test 7-55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-32: Generate an ATP Report 7-60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 7-33: Copy Files from LMF to a Diskette 7-61. . . . . . . . . . . . . . . . . . . . . . . .

Table 7-34: Copying CAL Files from Diskette to the CBSC 7-62. . . . . . . . . . . . . . .