Owner's Manual

• GEN5X2 On-Board Battery Charger
• (2) #8 27mm Self-Tapping Screws
• User Guide & Warranty
Retail Packaging:
Dimensions:
7.22” x 5.16” x 5.16”
Weight: 1.85lbs
UPC: 0-46221-19044-1
Inner Carton:
Dimensions:
7.44” x 5.3” x5.5.59"
Weight: 2.95lbs
Master Carton:
Dimensions:
11.77” x 8.03” x 11.5”
Weight: 7.4lbs
Quantity: 4
UCC: 10046221190448
Units Per Pallet:
192 Units
Retail Packaging:
Dimensions:
9.57” x 7.25” x 5.629”
Weight: 4.404lbs
UPC: 0-46221-19045-8
Inner Carton:
Dimensions:
9.57” x 7.25” x 5.63"
Weight: 4.404lbs
Master Carton:
Dimensions:
15.55” x 10” x 12.125”
Weight: 17.614lbs
Quantity: 4
UCC: 10046221190455
Units Per Pallet:
120 Units
Retail Packaging:
Dimensions:
10.315” x 9.016” x 5.629”
Weight: 7.189lbs
UPC: 0-46221-19046-5
Inner Carton:
Dimensions:
10.135” x 9.016” x 5.629"
Weight: 6.09lbs
Master Carton:
Dimensions:
10.905” x 9.606” x 12.125”
Weight: 12.175lbs
Quantity: 4
UCC: 10046221190462
Units Per Pallet:
96 Units
CURRENT
PER BANK:
OUTPUT
POWER:
CHARGING
BANKS:
CHARGING
CURRENT:
DIMENSIONS:
WEIGHT:
5A
10A 15A
72W 145W 220W
1 2 3
5A
WHATS IN
THE BOX:
VOLUMETRICS:
• GEN5X1 On-Board Battery Charger
• (2) #8 27mm Self-Tapping Screws
• User Guide & Warranty
• GEN5X3 On-Board Battery Charger
• (2) #8 27mm Self-Tapping Screws
• User Guide & Warranty
120-240 VAC, 50-60Hz
1V (12V)
<0.5mA
-20°C to +50°C
IP68
Natural Convection
BACK CURRENT
DRAIN:
INPUT/ WORKING
VOLTAGE AC:
HOUSING
PROTECTION:
AMBIENT
TEMPERATURE:
COOLING:
LOW-VOLTAGE
DETECTION:
TECHNICAL SPECIFICATIONS
20Ah
40Ah
80Ah
100Ah
120Ah
3hr
6hr
12hr
15hr
18hr
CHARGING TIMES
Battery Size
*Approximate charging times
at 50% depth of discharge.
Used for 12V wet cell, gel, enhanced flooded,
maintenance-free, & calcium batteries.
Used for 12V AGM or maintenance-
free batteries.
AGM
LITHIUM
Used for 12V lithium-ion batteries (including
lithium iron phosphate). Only for batteries
with Battery Management Systems (BMS).
FORCE MODE
Used to charge batteries below 1V.
All charge mode LED’s will flash and
the selected mode will illuminate.
Management Systems (BMS).
CHARGING MODES ADVANCED DIAGNOSTICS
There is a possible battery short or the battery
will not hold a charge. Consult a professional.
BAD BATTERY
12V
Used to repair old, idle, damaged,
stratified, or sulfated batteries.
REPAIR
The charger is in standby or the battery
voltage is too low for the charger to detect.
STANDBY
The battery voltage is too high for the
selected charge mode. Check the battery
and charge mode.
HIGH VOLTAGE
Charger is connected to the battery in
reverse. Reverse the connections.
REVERSE POLARITY
6.4 x 4.7 x 2.1in
(163 x 119 x 53mm)
7.1 x 5.7 x 2.2in
(180 x 145 x 56mm)
The new integrated thermal sensor automatically monitors and
adjusts the charging cycle based on fluctuations of ambient tem-
perature. Avoids under-charging in cold weather down to -4F° and
avoids over-charging in hot weather up to 104F°.
THERMAL COMPENSATION.
no.co
4.6 x 2.9 x 1.9in
(117 x 74 x 48mm)
1.85 lbs
(0.84 kg)
4.17 lbs
(1.89 kg)
5.76 lbs
(2.61 kg)
GEN5X1 GEN5X2 GEN5X3