Installation Guide

5
Lifetime Limited Warranty
Lifetime Limited WarrantyLifetime Limited Warranty
Lifetime Limited Warranty:
- If this product fails in form, finish or function due to materials or workmanship at any time during the life of the product, Innovative
Product Sales International LLC will replace this free of charge less shipping & handling. This does not include any claim arising from
installation error, abuse, damage, alteration, misuse or normal wear. Contact us at 7345 West Friendly Ave Suite C, Greensboro, NC
27410
Limitation of L
Limitation of LLimitation of L
Limitation of Liability
iabilityiability
iability
- OTHER THAN THE LIFETIME LIMITED WARRRANY STATED ABOVE, TO THE EXTENT PERMITTED BY LAW, IPSI DISCLAIMS ALL OTHER IMPLIED OR EXPRESS
WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITLY AND/OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY IS YOUR SOLE
REMEDY AND IPSI SHALL NOT BE LIABLE FOR ANY DAMAGES, WHETHER DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL, EXEMPLARY, OR
OTHERWISE, INCLUDING LOST REVENUES ARISING OUT OF ANY THEORY OR RECOVERY, INCLUDING STATUTORY, CONTRACT OR TORT. NOTWITHSTANDING
THE TERM OF ANY LIMITED OR IMPLIED WARRANTY, OR IN THE EVENT THAT ANY LIMITED WARRANTY FAILS OF ITS ESSENTIAL PURPOSE, IN NO EVENT WILL
IPSI’s ENTIRE LIABILITY EXCEED THE PURCHASE PRICE OF THIS PRODUCT. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE AND PROVINCE TO PROVINCE.
Care and Maintenance
Care and MaintenanceCare and Maintenance
Care and Maintenance
1. Use mild soap and water to clean the grab bars. Do not use abrasive materials as they could damage the finish and void
the warranty.
2. Check routinely that the grab bar is secure and tighten as necessary.
3. Avoid using any harsh cleaning products on or around the bar or adapters as this could damage the finish and weaken the
adhesion. If spray chemicals are used, avoid allowing these to collect around the adapters.
Frequently Asked Questions
Frequently Asked Questions Frequently Asked Questions
Frequently Asked Questions
>What kind of surfaces is t
What kind of surfaces is tWhat kind of surfaces is t
What kind of surfaces is the
he he
he nie wieder bohren
nie wieder bohrennie wieder bohren
nie wieder bohren.
..
. system suitable for?
system suitable for? system suitable for?
system suitable for?
Almost any smooth or rough surface is suitable if it is firm and able to bear the load in question. The nie wieder bohren. system is perfect for
high-quality materials that one does not want to damage by drilling. nie wieder bohren. is suitable with ceramic (tiles), stone, marble, granite,
glass, concrete, metal, wood and many plastics*. Based on load bearing for grab bars, it is recommended that you use this only on tile, stone,
metal and heavy duty glass. Unsuitable surfaces, on the other hand, include soft plaster, wallpaper, sheetrock and textiles (such as carpets),
which do not provide sufficient firmness and support for surface attachments. There is no adhesion to polyethylene (PE), polypropylene (PP) and
polytetrafluoroethylene (PTFE, Teflon). These surfaces are rarely found in tub surrounds or bath enclosures.
Although we have described as many examples as possible, our instructions can cover only some of the many surfaces and surface
treatments that are suitable. The user is therefore advised to make preliminary tests when considering other types of surface. Although the
system will work on most plastics and fiberglass, the actual load capacity will vary based on plastic material type, manufacture and wall
thickness. For this reason we can not guarantee 250lb load capacity for these surfaces. We do not offer lifetime guarantee for these
surfaces.
>Will the system work on rough surfaces too?
Will the system work on rough surfaces too?Will the system work on rough surfaces too?
Will the system work on rough surfaces too?
Surface texture is not a factor that affects the bonding strength of the nie wieder bohren. adhesive. However, the surface must be flat to match
the adapter and should not have any large gaps that would let adhesive escape from underneath the adapter ring. In fact, a slightly roughened
surface affords even better adhesion owing to the improved mechanical contact. To completely remove the silicone-like adhesive from the gaps
and pores of rough surfaces, it is necessary to use a silicone remover, pure alcohol and a coarse brush.
>Can I use the system outdoors as well?
Can I use the system outdoors as well?Can I use the system outdoors as well?
Can I use the system outdoors as well?
Yes! The adhesive will not decay, withstands UV radiation, is water-resistant and not damaged by freezing (however, it should be applied at a
temperature between 41 and 104°F (+5 and +40°C).
>Will the system fail over time?
Will the system fail over time?Will the system fail over time?
Will the system fail over time?
Absolutely not! Once the nie wieder bohren. system has been properly attached, its special single-component adhesive will ensure a permanent
bond. Moreover, it will retain its elasticity and not fray the way many textile adhesive tapes do after only a few weeks. Moreover, short impact
loads will not cause the adhesive surface to crack, as often happens with two-component adhesives that harden to form a crystalline
connection. The nie wieder bohren. system is a totally new experience in bonding technology!
>I followed the instructions
I followed the instructionsI followed the instructions
I followed the instructions carefully, but the adapter still fell from the wall. Why did that happen?
carefully, but the adapter still fell from the wall. Why did that happen? carefully, but the adapter still fell from the wall. Why did that happen?
carefully, but the adapter still fell from the wall. Why did that happen?
According to our experience, if the nie wieder bohren. system fails to deliver what we promise, it is usually for one of the three reasons listed
below. Each of these reasons is caused by improper conditions for bonding. From the so-called fracture pattern of the adhesive on the back of
the adapter, one can easily determine what the problem is.