Installation Guide

3
10. Put tube into the center hole of the adapter
and very slowly
very slowlyvery slowly
very slowly turn the tube key to insert
the adhesive. Continue to insert until the
adhesive beads up from each of the three
vent holes. Do not
Do not Do not
Do not disturb or
disturb ordisturb or
disturb or apply pressure
apply pressure apply pressure
apply pressure
on the adpater after inserting the adhesive
on the adpater after inserting the adhesive on the adpater after inserting the adhesive
on the adpater after inserting the adhesive
for 24 hours
for 24 hoursfor 24 hours
for 24 hours !
!!
! (See pics. 11, 12 and 13) Should
adhesive tube be empty before it beads up
from each vent hole, please open another tube and continue insertion as described. Do not attemp
Do not attempDo not attemp
Do not attempt to wipe off any excess adhesive right
t to wipe off any excess adhesive right t to wipe off any excess adhesive right
t to wipe off any excess adhesive right
after insertion into the adapter
after insertion into the adapterafter insertion into the adapter
after insertion into the adapter since this could compromise the bond
since this could compromise the bond since this could compromise the bond
since this could compromise the bond!
!!
! The beads can be easily removed once adhesive has dried
The beads can be easily removed once adhesive has dried The beads can be easily removed once adhesive has dried
The beads can be easily removed once adhesive has dried
completely
completelycompletely
completely.
11. After adhesive has cured (hardened) for 24 hours, remove the excess vent hole beads as shown in picture
14. Make sure that the excess from the center hole is removed evenly
Make sure that the excess from the center hole is removed evenlyMake sure that the excess from the center hole is removed evenly
Make sure that the excess from the center hole is removed evenly since the adapter’s surface has to be
completely smooth in order to mount the grab bar correctly. Carefully using a razor knife to do so might be
neccessary.
12. Reattach grab bar to the adapters using the machine screws and spacers
(see pic. 15 and 16). If holes do not line up, flip grab bar over as this proper
orientation is key to alignment. Loosely attach all screws first before
Loosely attach all screws first before Loosely attach all screws first before
Loosely attach all screws first before
tightening
tighteningtightening
tightening. Failure to
Failure toFailure to
Failure to use the screws without the spacers could damage
use the screws without the spacers could damage use the screws without the spacers could damage
use the screws without the spacers could damage
the adapter and bond
the adapter and bondthe adapter and bond
the adapter and bond.
..
.
13. Slide cover ring over mounting flange after having ensured tightness of all screws. Turn in one direction
until the ring is properly aligned and assure a snug fit. Note there should be a small gap between cover ring
and wall to provide proper drainage of water.
..
. Pointer: the plate is easily attached if it is turned to the
proper position and then snapped on. The ring is concentric and works best when "dialed in place”(see pic.
17).
14. Test for proper installation to be sure bar is firmly mounted by applying some pressure.
Adapter Removal:
Adapter Removal:Adapter Removal:
Adapter Removal:
The
The The
The nie wieder bohren
nie wieder bohrennie wieder bohren
nie wieder bohren.
..
. adapter system can be removed from any hard surface by applying torsion
adapter system can be removed from any hard surface by applying torsionadapter system can be removed from any hard surface by applying torsion
adapter system can be removed from any hard surface by applying torsion
Option 1
1. Remove grab bar from the adapters by taking out the screws and spacers (see pic. 18).
2. Use channel locks and firmly turn the adapter applying consistent pressure (see pic. 19).
3. Remove residual adhesive from surface using a razor knife and wipe with acetone remover as needed. For
rough surfaces, a coarse brush can also be used. When using a coarse brush, please wear protective
goggles to protect your eyes (see pic. 20)
11
1111
11
12
1212
12
14
1414
14
15
1515
15
17
1717
17
16
1616
16
13
1313
13
18
1818
18
19
1919
19
20
2020
20