Installation Guide

ManualsBrandsNo Drilling Required ManualsBath18 in. x 1-1/2 in. Grab Bar in Brushed Stainless Steel

Mounting:

Mounting:Mounting:

Mounting:

nie wieder bohren

nie wieder bohrennie wieder bohren

nie wieder bohren.

no drilling required

no drilling requiredno drilling required

no drilling required.

. technology mounting system: (r

technology mounting system: (r technology mounting system: (r

technology mounting system: (recommended

ecommended ecommended

ecommended for Tile, Natural Stone,

for Tile, Natural Stone,for Tile, Natural Stone,

for Tile, Natural Stone,

Concrete,

Concrete,Concrete,

Concrete, Glass

Glass Glass

Glass &

& &

& Metal

Metal Metal

Metal

Components:

Components:Components:

Components: T

Tools required:

ools required:ools required:

ools required:

-Grab bar -Level

-GB00002-NDR (mounting kit) -Clean dry cloth

Note: Failure to follow the instruction sheet completely may result in a product failure

Note: Failure to follow the instruction sheet completely may result in a product failureNote: Failure to follow the instruction sheet completely may result in a product failure

Note: Failure to follow the instruction sheet completely may result in a product failure and will void the warranty. Please be sure

and will void the warranty. Please be sure and will void the warranty. Please be sure

and will void the warranty. Please be sure

to carefully read and follow the instructions for optimum results and safety.

to carefully read and follow the instructions for optimum results and safety.to carefully read and follow the instructions for optimum results and safety.

to carefully read and follow the instructions for optimum results and safety.

GB00002-NDR Adapter Set: 2 Adapters, 3 Adhesive Tubes, 3 Red Tube Keys, 6 Stainless Steel Machine

Screws, 6 Spacers, 1 Allen Wrench, 1 Alcohol Cleaning Cloth (see pic. 1)

The key to successful installation is proper wall preparation and cleaning. Inspect surface to be sure

desired mounting surface

mounting surfacemounting surface

mounting surface is completely flat

completely flatcompletely flat

completely flat at all six fastening points. The bar should not rock or have gaps

between the base and the wall.

Next step is proper cleaning. If surface has any

If surface has anyIf surface has any

If surface has any sealant, wax or hard water residue

sealant, wax or hard water residuesealant, wax or hard water residue

sealant, wax or hard water residue, it is recommended that

you lightly sand the surface with a

lightly sand the surface with alightly sand the surface with a

lightly sand the surface with an

n extra fine paper to remove this residue

extra fine paper to remove this residue extra fine paper to remove this residue

extra fine paper to remove this residue. This will not scratch the

surface but will allow for proper adhesion. Next, clean the surface with pure acetone and/or the supplied

cleaning cloth. Allow to dry fully for about 30 minutes. After the surface has fully dried, wipe any residue

from the surface with a clean dry cloth. Do not use household cleaners as they can leave a residue and be

Do not use household cleaners as they can leave a residue and beDo not use household cleaners as they can leave a residue and be

Do not use household cleaners as they can leave a residue and be

sure surface has completely dried prior to installation

sure surface has completely dried prior to installationsure surface has completely dried prior to installation

sure surface has completely dried prior to installation

(see pic. 2).

Slide grab bar end cover ring away to expose

the three hole base plate. Slide a spacer over

each machine screw and pre-attach the

adapters to the grab bar by using the allen

wrench (see pic. 3, 4 and 5). If the wall cover

ring cannot be easily removed from the grab

bar, simply tap bar end in the cup of your hand

to pop it loose.

Identify desired location of bar. If needed, use level and mark location for bar placement.

Carefully remove the adapters’ protective film from foam rings on both

sides. Be careful not to tear the foam ring and do not touch the adhesive on

foam rings! Carefully press the grab bar into place in the desired location for

5 seconds. The adhesive rings are meant to temporarily hold the adapters in

place to ensure safe insertion of the special adhesive. Therefore, do not

Therefore, do not Therefore, do not

Therefore, do not

apply too much pressure on the grab bar!

apply too much pressure on the grab bar!apply too much pressure on the grab bar!

apply too much pressure on the grab bar! Once the adapter makes contact

with surface, it cannot be removed without damaging ring. Be sure you have

clearly marked the location before attaching. (See pic. 6 and 7)

Remove the grab bar from the adapters again by removing the screws and spacers. If you are mounting

horizontally or vertically, remove the screws and spacers on the lower end first to prevent potential injury.

After removal of all screws and spacers, the adapters are now fixed to the wall in the proper location

location (see pic. 8).

To open the black adhesive tube, carefully pierce the seal with the pointed end of the red tube key (see

pic. 9).

Slide the slotted portion of the red tube key over tube end and engage folded end of tube. It may be easier

to slightly unfold the tube end before inserting into the red tube key (see pic. 10). Be careful not to squeeze

or advance the glue from tube before next step.

1010