Nixeus Technology, Inc Nixeus Vue 30 IPS 2560x1600 Monitor (NX-VUE30)
Table of Contents Important Information 3 2. Getting Started Box Content Installing Base Stand 5 Input and Connection Ports 5 Power Cable and Supply Switch 6 3. 8 1. Settings 5 5 On screen Setting Display 8 OSD SETTING Sub-menu 8 Brightness 11 Image 14 Color Temp Color Temperature Calibration 15 MISC 17 Reset 20 4.
Important Information Important Note: Please make sure your computer hardware graphics card supports the Nixeus Vue 30” IPS Monitor. Some devices and connections may not be able to support the full 2560x1600 resolution. If you are not sure, please contact your computerhardware’s manufacturer. Please read this manual before using the Nixeus Vue 30” NXVUE30 with your computer. It contains important information regarding use and care of IPS Monitors.
Avoiding Image Persistence, Incidental Image or After Image: 1) When the monitor is on and unattended, please use a moving screen saver. If there is a static (non moving image) on the screen, please refresh regularly or start an application to start using the screen. 2) Long time continuous display of static images may case a “brand” on the screen; this is also cal “image persistence” or “incidental image” or “after image.
Getting Started Box Contents: • Nixeus Vue 30” IPS 2560x1600 Monitor (NX-VUE30) • Stand Base x 1 (with 4 screws) • Dual Link DVI-D Cable x 1 • Power Adapter & Power Cable x 1 • 3.5mm Audio Auxiliary Cable x 1 • NX-VUE30 Quick Start Guide Installing Base Stand: (Tools needed – Philips Screw Driver) Carefully lay the monitor on its’ back on a static free, clean, flat surface. Connect base to stand and line up connectionholes. With the four connection screws provided, secure base to stand.
NX-VUE30 Power Cable and Power Supply Switch: Only use the power cable included with the NX-VUE30. Using any other un-authorized power adapters may damage your monitor and void your warranty. 1. Connect the power cable to internal power supply on the back of the monitor (make sure power switch is off beforeconnecting the cable). Next use the ON/OFF switch to turn on the internal power supply.
Monitor Swivel Left/Right: Make sure the NX-VUE30 is on a stable level surface. Holding the left and right bezel with your hand, carefully adjust monitor left or right to desired orientation. Monitor Tilting Foward/Back: Use both hands, hold the top and bottom or right and left to tilt the monitor as shown in the pictures.
Settings ON SCREEN DISPLAY (OSD): For the On Screen Display to be visible on the monitor, a video signal must be transmited to the monitor from your PC/MAC. The six buttons you will use to navigate the On Screen Display (OSD) are “AUTO,” “MENU,” “VOL+,” “VOL-,” “UP,” and “DOWN.” These buttons can be found on the bottom right corner under the bezel with their corosponding logos. The On Screen Display feature that allows the user to adjust monitor settings without relying on a PC or Mac’s software.
3) Next press the “MENU” button to access the Language selection. 4) Then press the UP or DOWN buttons to highlight your preferred language and press the MENU button to select/activate your language. If you want to adjust the horizontal placement of the OSD MENU on your monitor; 1) Press the DOWN or the UP button to navigate and highlight OSD H. POS then press MENU to highlight the progress bar. 2) Use the VOL+ and VOL- buttons to adjust the value for your desired settings.
The same steps can also be performed to adjust the vertical placement of the OSD MENU by navigating to the OSD V. POS and adjusting the progress bar. The default duration of the OSD MENU before it automatically disappears is 10 seconds. 1) To adjust this setting, in the OSD SETTING sub menu, use the UP or DOWN button to scroll down to OSD TIMER and press menu to highlight the progress bar. 2) Then use the VOL+ or VOL- buttons to adjust the time for the OSD MENU.
BRIGHTNESS Sub-Menu: To adjust the settings in the BRIGHTNESS Sub-Menu, first press the MENU button bring up the OSD, then press MENU again to access the BRIGHTNESS Sub-Menu. 1) To adjust the monitor’s brightness, use the UP and DOWN buttons to navigate to BRIGHTNESS then press the MENU button to highlight the progress bar. 2) Next use the VOL+ or VOL- buttons to adjust your preferred brightness settings.
1) To adjust the Contrast Ratio, in the BRIGHTNESS Sub-Menu, use the UP/DOWN buttons to navigate to CONTRAST 2) Then press the MENU button to select CONTRAST to adjust the progress bar to your preferred contrast ratio settings. The ECO settings have 4 preset brightness/contrast settings - STANDARD, GAME, MOVIE, and TEXT. 1) In the BRIGHTNESS Sub-Menu, use the UP/DOWN buttons to navigate to ECO and press the MENU button.
Dynamic Contrast Ratio (DCR) can also be adjusted in the BRIGHTNESS Sub-MENU. 1) Use the UP/DOWN buttons to navigate to DCR and press the MENU button. 2) Using the VOL+/VOL- buttons you can turn DCR to ON or OFF. Pressing the AUTO button will exit DCR.Please note if DCR is turned ON, you cannot adjust the BRIGHTNESS and CONTRAST settings. You must adjust your BRIGHTNESS and CONTRAST settings prior to turning ON DCR.
3) Once you are finished with your adjustments in the BRIGHTNESS Sub-Menu, press AUTO twice to exit out of the OSD. IMAGE Sub-Menu: In the IMAGE Sub-MENU, you are only able to adjust the ASPECT Ratio of the monitor to either WIDE or 4:3. The recommended settings is to set the ASPECT ratio to WIDE. 1) First press the MENU button to bring up the OSD, then use the UP/DOWN buttons to browse to the IMAGE sub-menu and press MENU again.
COLOR TEMP Sub-Menu: 1) Press the MENU button to bring up the OSD. 2) Use the Up/Down buttons to navigate to COLOR TEMP, then press the MENU button. 3) Use the VOL+/VOL- to browse or select one of 3 preset color temperatures; Normal, Warm, or Cool. Once selected, you may press the “AUTO Button twice to exit and apply the settings.
Color Temperature Calibration in COLOR TEMP Sub-Menu: NOTE: For accurate color calibration, we recommend using a hardware colorimeter 1) In the COLOR TEMP Sub-Menu, use the VOL+/VOL- button to select the “USER” preference and press the MENU button. 2) Use the UP/DOWN button to select which color temperature to customize and press the MENU button to highlight the progress bar. 3) Next, use the VOL+/VOL- to adjust the desired settings of the color’s temperature.
MISC Sub-Menu: 1) Press the MENU button to bring up the OSD. 2) Using the UP/DOWN buttons, browse to the MISC sub-menu and press the MENU button. 3) Using the UP/DOWN buttons navigate to either HOTKEY TYPE, SIGNAL SOURCE, AUDIO SELECT or VOLUME that you wish to adjust or change then press the MENU button. 4) Use VOL+/VOL- to change the settings and press AUTO to exit out of that setting. HOTKEY TYPE: With no On Screen Display present, the UP and DOWN button also functions as hot keys.
SIGNAL SOURCE: This setting allows you to change the video signal source to either VGA, DVI, HDMI, or DP. This function can also be accessed without the On Screen Display by simply just pressing the AUTO button.
AUDIO SELECT: This setting allows you to choose which audio source to transmit sound to the monitors speakers. Select DIGITAL only if you are using a HDMI or DP video signal source. Choose ANALOG is you are using DVI or VGA connection cables with the 3.5mm audio cable.
VOLUME: This setting allows you to adjust the volume setting of the monitors internal speakers. RESET Sub-Menu: 1) Press the MENU button to bring up the OSD 2) Using the UP/DOWN buttons, browse to the RESET sub-menu and press the MENU button. 3) Pressing the MENU button again while the RESET is highlighted in red will reset ALL OSD settings to the factory default settings. If you need additional assistant, please contact Nixeus Technology toll free at 888-983-4128 or e-mail techsupport@nixeus.
Nixeus Technology, Inc. (“Nixeus”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from Nixeus or its authorized reseller or distributor, and • Only for products purchased and delivered within the the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO, and Canada.
• After an RMA number is assigned, the defective/malfunctioning product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit to Nixeus Technology, Inc. The RMA number must be visibly and clearly marked on the outside of the package. Do not include any manuals or accessories in the shipping package, Nixeus will only replace/repair the defective/malfunctioning product and will not ship back any accessories.
Warning: This product contains mercury, a chemical known to cause cancer in the State of California. Please handle with care and dispose of properly. Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply.
