Model: 7151 Installation Manual READ THE INSTRUCTIONS CAREFULLY, familiarize yourself with all the parts as shown in the exploded view. The exploded view will also provide a helpful reference when relating to the location of the various parts and how they are mounted.
Fixed Panel (1 pcs) | Door Panel (1 pos) | Rollers (2 pos) | Glass Holders (2 poss Stoppers (2 pes) | Bottom guide (1 pes) | Running rail (1 pes) Wall bracket (2 pos) | Wall channel (1 pes) Litton track cover (1 poet Door gasket (1 pos) | Gap gasket (2 pos) Handle (1 pes) Bottom track {1 pes) Countersunk head ST3.
Tools 5mm 4mm 2 .5mm @6 drill bits \ 4 Hex key Install rod Positioned Drill and Assorted Bits Knife Pencil 28 drill bits Caulk Gun Masking Tape Level Claw Hammer Assorted to 6' (1.8m) Screwdrivers Before You Begin CAUTION: Risk of personal injury. Always wear safety glasses while cutting or drilling. CAUTION: Risk of injury or product damage. Unframed tempered glass should not contact hard surfaces or it may shatter. Do not touch the edge of the tempered glass panel with tools or any hard objects.
Choose the shower door open direction left or right. Follow the appropriate diagram below . Left Hand Assembly Right Hand Assembly STEP 1: Install rollers to door. Pick up the rollers from the package, install them to door panel as illustrated, fastened by Hex key 4mm.
STEP 2: Put the door panel in the inside of your shower room and have the wood blocks up the bottom as illustrated. LL — STEP 3: Use a professional level and the positioned provided to determine the wall Chanel's position as illustrated.
STEP 6: Install the wall channel. Fasten the wall channel according to the holes from abbe steps by ST3.5x35 screws. Install the wall bracket. The wall bracket has two parts, now take out inner part-the bracket base which like the pics shown. Bracket base tends to slip down on the single mounting screw.
STEP 10: Install the Bottom track. Fasten the bottom track according to the holes as above steps by ST3.5x35 screws. STEP 11: Use caulk gun inject Clear Silicone Sealant to the wall channel and bottom track.
STEP 12: Install the fixed panel. Put the fixed panel into the Bottom track and the Wall channel. STEP 13: Measure and Cut the Running Rail. Measure from wall to wall at the top of the shower door opening. Mark the running rail at the determined distance. Cut from end. Cut the rough edges smooth where the running rail was cut. Taking care to avoid damaging finished surfaces. The cut running rail should put flush on between walls without hand pressure.
STEP 14: Install the stoppers. Position the stoppers on the running rail, secure them temporarily in place. Do not fasten them, fasten it after install the fixed panel and glass panel. Position the outer part of wall brackets on the running rail. Secure them temporarily in place. Install some parts of glass holders on the running rail as illustrated. Hex key 4mm Hex key 4mm Hex key 4mm Hex key 4mm STEP 15: Fasten the running rail. Fasten the outer part of wall bracket.
STEP 16: Install the bottom guide. Use positioned to determine the bottom guide's position as illustrated 1. Drill holes with {28 drill bit as illustrated 2. Fasten the bottom guide according to the holes from above steps by @8 wall plugs and screws, as illustrated 3 & 4. Check the bottom guild. Put the black rubber to 10mm position. This bottom guild fit for 3 different thickness. Secure the thickness is for 10mm glass. Fasten the bottom guild as illustrated. STEP 17: Install the door panel.
STEP 18: Install the handle as illustrated. Install the door gasket and gap gaskets. Insert the door gasket to the wall side. And insert another gap gasket to another side of glass door. Insert another gap gasket to the fixed panel. | Cut the gap gaskets Cut the gap gaskets | as illustrated. as illustrated. CJ lL] Install the Glass fix nails as illustrated. (14 Lengthy Lengthy) =O" B= 4) short Short 14) ? Measure and Cut the Bottom track cover. Measure from wall to fixed panel at the bottom track.
STEP 19: Fasten the stopper and rollers. Sliding the door panel, check the position of stopper in the running rail. Secure them temporarily in place, and fasten them. Fasten the rollers by Hex key 2.5mm and 4mm. Note: Hex key 2.5mm to stop the roller moving as fasten the rollers. Seal the door assembly: Apply silicone between the bottom of the fixed panel and the base. Silicone application along the wall channel is also suggested. In both cases, it is done from the outside of the shower area.
