User's Guide

LUMINA
™
MAX 2500 USER GUIDE - ENGLISH
UNLOCK BEFORE USE. LOCK THE HEADLAMP BEFORE TRANSIT OR
STORAGE
It is important to lock the headlamp and protect the switch from being
pressed while it is in transit. The headlamp can be easily turned on if placed
in something like a backpack, duel bag or suitcase. The headlamp gets hot
while in operation. To prevent potential damage from high heat or even re, it
is very important to put the headlamp in lock mode and protect the switch
from being pressed. NiteRider® will not be held responsible for damages
to person or property resulting from a failure to follow the ‘lock’ mode
instructions.
WARNING
A bicycle without correct lights and reectors might be dicult for other
people to see, and you might not be able to see. If you can not see, or other
people can not see you, you could have an accident. Make sure your lights
operate correctly and that batteries are charged.
WARNING !!HOT SURFACES!!
DO NOT USE THE LUMINA™ MAX AS A HAND HELD LIGHTING DEVICE
WHEN IN HIGH AND BOOST MODES!
PARTS LIST AND IDENTIFICATION
Please verify the contents of your Lumina™ Boost lighting system:
A. Lumina™ Max Front Light
B. Handlebar Clamp Mount
C. USB-C Charging Cable
D. AC Charging Adapter
MOUNTING THE HANDLEBAR CLAMP MOUNT AND HEAD LIGHT
The Handlebar Clamp Mount (HCM) is designed to t on virtually any
handlebar (25.4mm - 35mm diameter handlebars).
1. Turn the knob counter-clockwise, allowing the hinge to swing open.
2. Place the HCM on the handlebar on the left side of the stem,
orienting the mounting rails with release tab towards rear.
3. Swing the hinge down to make contact with the handlebar.
4. Swing the bolt up, seating the knob into its recess.
5. Turn the knob clockwise to tighten and secure the mount to the handlebar.
RELEASE TAB
MOUNTING RAILS
SWITCH #1SWITCH #2
MOUNTING THE HEAD LIGHT ONTO THE HANDLEBAR CLAMP MOUNT
With the light facing forward, align bottom mounting rails of light to top of
rails of HCM. Pull light back along the rails until tabs engage and lock into
place. Test for a secure tment by pushing light forward, ensuring there is no
movement and that tabs have engaged into the light base. Do not push the
release tab when testing for a secure tment.
To remove the head light, press the release tab down and slide the head light
forward.
Note: After mounting the headlamp, adjust it so the beam illuminates your
path without distracting oncoming riders.
OPERATION
Note: The unit can operate in Walk and Low Mode while charging.
1. For the initial power ON, the light will need to be unlocked.
Press and hold any single button for 8-10 seconds to unlock.
2. A single press of power button switch #1 button will power ON in High
Mode. To power ON in Low Mode, press power button switch #2.
3. To increase power, press power button switch #1. To decrease power,
press power button switch #2. Steady light mode settings are in the following
order WALK, LOW, MEDIUM, HIGH, AND BOOST.
A. Walk Mode is indicated by a slow pulse yellow LED
in the LED switch.
B. Low Mode is indicated by a steady yellow LED light
in the LED switch.
C. Medium Mode is indicated by a steady green LED light
in the LED switch.
D. High Mode is indicated by a steady blue LED light
in the LED switch.
E. Boost Mode is indicated by a steady red and blue LED light
in the LED switch.
4. To access ash modes, press and hold any power button switch
for 3 seconds until the light begins to ash.
A. Cycle through 3 ash modes by pressing power button
switch #1 or #2.
B. Flash mode is indicated by a blue LED light in the LED power
button switch that mimics the selected ash pattern.
C. To return to steady light modes, press and hold any power
button switch for 3 seconds until steady ON light appears.