Black plate (5,1) Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (6,1) FOREWORD NISSAN NAVIGATION SYSTEM HELPDESK CONTACT INFORMATION For assistance or inquiries about the NISSAN Navigation System, or to order updated map data, contact the NISSAN NAVIGATION SYSTEM HELPDESK at: . ADDRESS: P.O. Box 1588, Orem, UT 84059-992 . E-MAIL: Nissan-Navi-Info@navteq.com . WEB SITE: www.NissanNavigation.com or www.nissan.ca . PHONE: 1-888-661-9995 .
Black plate (1,1) Table of Contents Introduction 0 About Multi function display system 1 Navigation 2 Audio system 3 Bluetooth® Hands-Free Phone System 4 Heater and air conditioner 5 Viewing technical information 6 Other settings 7 Voice recognition 8 Multi function meter 9 General system information 10 Troubleshooting guide 11 Index 12 Model "R35-N" Edited: 2009/ 10/ 30
Black plate (1,1) 0 Introduction How to use this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-2 For safe operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-2 Reference symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-2 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-3 Functions disabled while driving . . . . . . .
Black plate (4,1) HOW TO USE THIS MANUAL This manual uses special words, symbols and icons, organized by function. Please refer to the following items and familiarize yourself with them. FOR SAFE OPERATION WARNING This is used to indicate a hazard that could cause death or serious personal injury. To avoid or reduce the risk, follow the information and instructions exactly. CAUTION This is used to indicate a hazard that could cause minor or moderate personal injury.
Black plate (5,1) SAFETY INFORMATION This system is primarily designed to help you reach your destination, and it also performs other functions as outlined in this manual. However, you, the driver, must use the system safely and properly. Information concerning road conditions, traffic signs and the availability of services may not always be up-to-date. The system is not a substitute for safe, proper and legal driving. Before using the navigation system, please read the following safety information.
Black plate (6,1) FUNCTIONS DISABLED WHILE DRIVING To ensure safe driving, some functions cannot be operated or have limited operation while driving. To use these functions, first park the vehicle in a safe location and then operate the navigation system.
Black plate (7,1) LASER PRODUCT TRADEMARKS This system is certified as a Class 1 laser product. The system complies with DHHS Rules 21 CFR Chapter 1, Subchapter J. WARNING . Do not disassemble or modify this system. There are no user serviceable parts in this system. . If maintenance, adjustments and operations other than those specified in this manual are attempted, injury due to laser radiation and exposure could occur.
Black plate (8,1) MEMO 0-6 Introduction Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (4,1) 1 About Multi function display system Features of multi function display system . . . . . . . . . . . . . . . . . 1-2 Navigation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Multi function meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Control buttons and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black plate (10,1) FEATURES OF MULTI FUNCTION DISPLAY SYSTEM MULTI FUNCTION METER NAVIGATION SYSTEM Contained within NISSAN’s authentic navigation system, the navigation and audio systems are all available for use. WARNING . Use the information from the multi function meter strictly as a reference to make your driving more comfortable. The readings are not meant to prevent accidents caused by reckless driving or poor driving conditions (due to weather, road condition, etc.).
Black plate (11,1) Performance and vehicle information Drivers can customize the panel by choosing up to six information gauges for the information they would like displayed. “CUSTOM VIEW SCREEN” page 9-7 Vehicle information items: — Engine coolant temperature — Engine oil temperature — Engine oil pressure — Transmission oil pressure — Transmission oil temperature Acceleration screen — Boost pressure — etc.
Black plate (12,1) Vehicle information items: . Acceleration screen . — Accelerator pedal position — Boost pressure — Resultant fore/aft g-force exerted on the vehicle “ACC ELERATION SCREEN” page 9-20 Braking screen . — Brake pedal position — Speed — Resultant fore/aft g-force exerted on vehicle “BRAKING SCREEN” page 9-22 Steering screen Information for fuel economy improvement Displays the selected gear for optimum fuel economy and the resulting fuel economy information.
Black plate (13,1) Trip calculator Available items: This allows you to record your driving time and waypoints. It also displays the history for both functions. . Stopwatch screen .
Black plate (14,1) CONTROL BUTTONS AND FUNCTIONS screen. 8 & 9 & : Push to display the multi function meter screen. < >: Push to return to the previous screen. In a settings screen, this button can also be used to apply the setting. In a character input screen, this button can also delete the characters that have been entered. 10 Center dial/: & CONTROL PANEL Navigation, Multi function meter 1 & 2 & 3 & 4 & 1-6 Monitor: Multi function screens appear here.
Black plate (15,1) 5 & 6 & 7 & 8 & Audio system & 1 2 & /: Turn this switch to manually tune the radio frequency. Push the switch to configure the sound settings. When using Music Box/CD (including MP3/WMA/AAC files on disk)/ DVD/USB memory/Bluetooth streaming audio (if so equipped)/iPod player you can change the album or folder to be played. Preset stations <1>-<6>: Use these buttons to toggle between the stations preset in the system.
Black plate (16,1) 8 & 9 & Heater and air conditioner & 1 2 & 3 & 1-8 : Push this to set the air conditioner to the automatic mode. Turn the dial to adjust the cabin temperature. When in dual mode, this switch adjusts the driver-side temperature. 4 & 5 & < >: Push this to recirculate the air in the cabin. 6 & : When the fan is ON, pushing this button turns the air conditioner ON/OFF. 7 & < REAR>: Push to turn the rear defroster ON/OFF.
Black plate (17,1) 3 & USB connector: Connect to play an iPod or a USB memory. DIGITAL MEDIA SLOTS 1 & 2 & CD/DVD slot: Insert a CD/DVD. : Push to eject a CD/DVD.
Black plate (18,1) 6 & 7 & STEERING SWITCH 1 & 2 & : Push the source select switch to change the mode in the sequence of Preset A, Preset B, Preset C, iPod® (if so equipped), Music Box, CD, DVD, USB memory and Bluetooth streaming audio (if so equipped) and AUX (if so equipped). If they are not ready to function, those modes will be skipped. : Allows you to adjust the volume. 3 & 4 & 5 & : When using the stopwatch, push this button to record the required travel time.
Black plate (19,1) START-UP SCREEN . The system saves the screen displayed at the time the engine is turned off. . “Clarion” logo is a registered trademark of Clarion Co., Ltd. and the “POLYPHONY DIGITAL” logo is a registered trademark of Polyphony Digital Corporation. 1. The navigation system starts when the ignition switch is pushed to the ACC or ON position. INFO: . After the engine is started, the operation instructions will only be displayed the first time the screen is displayed. .
Black plate (20,1) BASIC OPERATION > to return to the previous 3. Push < screen without applying any changes. Push
Black plate (21,1) INFO: Using controls to adjust values, levels, etc. There are three main methods you can use to control the navigation system: the center dial or the touch panel. Use these controls to adjust the volume of phone and voice guidance, the display brightness, etc. . You can also adjust the volume of phone and voice guidance, etc. by tilting the steering switch up and down. . This same adjustment can also be made by the touch panel operation. “LIST SCREEN” page 1-14 How to adjust: 1.
Black plate (22,1) 5 * 6 * 7 * 8 * LIST SCREEN After searching for a point of interest, a list screen is displayed. Depending on the list displayed, it can be sorted. Items displayed in list 1 * Highlight the preferred item from the list and push to select it. If a location or facility name is not completely displayed (due to length), highlight the item to display the hidden part of the name. 2 * 3 * 4 * An item that starts with the selected letter will be displayed at the top of the list.
Black plate (23,1) TOUCH PANEL OPERATION With this system, it is possible to use the center dial and touch panel operation to perform the same operations. Adjusting volume and others Inputting letters and numbers Touch [+] or [−] located on the right and left of the bar graph to perform the adjustment. 1. Touch the letter or number. This manual describes the operations using the center dial.
Black plate (24,1) HOW TO INPUT LETTERS AND NUMBERS INFO: CHARACTER (letters and numbers) INPUT SCREEN Alphanumeric characters are entered to set a destination, search for a facility, edit stored locations, etc. 3. Push < >, or highlight [Delete] and push to delete the last character entered. Push and hold < characters entered. 1. Use the touch panel or center dial to highlight a character on the displayed keyboard. .
Black plate (25,1) NUMBER INPUT SCREEN A phone number or a street number can also be entered as a search method to look for a destination. Perform the following procedure to enter a number. INFO: Only the locations included in the map data database can be searched for by a phone number. 2. Push . The highlighted number is entered. 4. After finishing the entry, highlight [List] and push . INFO: 1. Use the touch panel or center dial to highlight a number on the displayed keyboard. .
Black plate (7,1) 2 Navigation Features of this navigation system . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Route guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Places of interest (PLACES) directory . . . . . . . . . . . . . . . . . 2-2 Address book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Avoid area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black plate (8,1) Speed limit indication on map . . . . . . . . . . . . . . . . . . . . . . . . . 2-94 Other navigation settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-94 Delete stored items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-98 Reset all navigation settings to default . . . . . . . . . . . . . .
Black plate (28,1) FEATURES OF THIS NAVIGATION SYSTEM ROUTE GUIDANCE The main features of the NISSAN Navigation System are visual guidance and voice guidance in selected map coverage areas. Utilizing a network of GPS (Global Positioning System) satellites, the NISSAN Navigation System tracks the location on the map and navigates to a preferred location. Once the destination is set in a map coverage area, the NISSAN Navigation System will calculate a route from the current location to the destination.
Black plate (29,1) DETOUR BirdviewTM VOICE GUIDANCE Two map types, the 2D (Plan View) map and BirdviewTM (3D) map, are available in the NISSAN Navigation System. BirdviewTM map displays the map from an elevated perspective. In BirdviewTM map, it is easy to recognize an image of the route because it provides a panoramic view over a long distance. Route guidance is provided through voice and visual instructions. Voice guidance announces the appropriate directions when approaching an intersection to turn.
Black plate (30,1) MAP SETTINGS MAP TYPES Two types of map views are available: 2D map and BirdviewTM (3D) map. 2D map The 2D map displays the map in a 2-dimensional environment similar to a road map. Screen information: 1 * 2 * 3 * 2-4 Vehicle icon: Indicates the current vehicle location and the direction of travel. Guide point: Indicates a guide point on the route. Remaining time and distance to the destination: Indicates the approximate remaining time and distance to the destination or waypoint.
Black plate (31,1) * 6 7 * 8 * 9 * Touch the icon to change the setting. : North always pointing up. : Direction of the vehicle always pointing up. “Setting map orientation” page 2-14 Scale indicator: Indicates the scale of the map. Touch the icon to display the scale bar. The map scale can be adjusted using the scale bar. “Operating with touch panel operation” page 2-7 Arrow: Indicates the distance to the next guide point and the turning direction at that guide point.
Black plate (32,1) DISPLAYING CURRENT VEHICLE LOCATION 3D building graphics (BirdviewTM map) INFO: In an area where the building graphics are not stored in the map data, the normal map is displayed even when the map is zoomed in. Operating with control panel The basic map screen displays the current location (the position where the vehicle mark is located). Push
Black plate (33,1) Operating with touch panel operation After moving the map, touch [BACK] on the map screen to display the current location map screen. MOVING MAP The operations for moving across the map are different between the 2D and BirdviewTM maps. 2D map The cross pointer is displayed, and the touched position is set as the center of the screen. 2. Touch the direction to move to. The map continues to scroll while the screen is touched. Fine-tuning the cursor position: 1. Touch [Slow].
Black plate (34,1) INFO: Fine-tuning the cursor position is not possible while driving. BirdviewTM (3D) map 3. Touch [ ] or [ of the map. ] to change the direction : Rotates the map clockwise. : Rotates the map counterclockwise. 1. Touch the screen. The cross pointer and 8-directional key are displayed. INFO: While driving, scrolling on the map is limited to a specified distance. 2. Touch the direction to move to. The map continues to scroll while the screen is touched.
Black plate (35,1) CHANGING SCALE OF MAP Operating with touch panel operation 1. Touch [ ]. The scale is displayed. Operating with center dial 1. Turn the center dial when the map screen is displayed. The map scale is displayed at the right side of the screen. 2. Use the center dial to adjust the map scale.
Black plate (36,1) Map scale INFO: Free zoom: Once the [Small Step Zoom by Dial] is set to ON in the setting screen, the scale can be changed in smaller steps when [ZOOM IN] or [ZOOM OUT] is pushed and held than when either button is briefly pushed. If briefly pushed, the operation returns to normal. Any required map scale (map coverage) between 320 miles (640 km) and 1/64 of a mile (25 m) can be selected. Scale level for 2D map and BirdviewTM map (3D) display: US Units Setting by voice command 1.
Black plate (37,1) Example: The widest level (BirdviewTM map) INFO: 1. Push while the current location map screen is displayed. 3. Highlight [Change View] and push the right button of the directional buttons. 4. Highlight the preferred map view and push . The indicator of the selected map view illuminates. The traffic information icons are not displayed on the map screen when the map scale is set to 32 miles (64 km) or higher. “Traffic information display and scale levels” page 6-12 5.
Black plate (38,1) half displays the map in BirdviewTM. 5. Highlight the preferred item and push . INFO: . . Setting by voice command When the split screen mode is selected, the map settings for the left screen can be changed independently. “Setting left screen display” page 2-16 If the split screen mode is selected, the normal map scrolling and scale adjustment are set in the right screen.
Black plate (39,1) 2. Highlight [Map View] and push . 4. Highlight the preferred item and push . Available setting items 3. Highlight [Map Settings] and push . . [Map Orientation]: Sets the map direction to North Up or Heading Up. “Setting map orientation” page 2-14 . [Long Range]: Sets the long range map view display on/off. “Settings long range map view” page 2-14 . [Map Color]: Changes the map color. “Setting map color” page 2-15 .
Black plate (40,1) Setting map orientation The map direction (orientation) can also be changed in the 2D map. These settings are available only in the 2D map or 2D/2D split map. location map screen. Available map orientations . [North Up]: The top of the map remains oriented to the north. . [Heading Up]: The top of the map follows the traveling direction. INFO: INFO: 1. Highlight [Map Orientation] and push .
Black plate (41,1) Setting map color . The map color can be changed to a warm or cool color, or a light color, to emphasize the traffic information. [Warm]: Sets warm colors for the map coloring. . [Cool]: Sets cool colors for the map coloring. . [Traffic Emphasis]: Sets light colors for the map coloring to emphasize the traffic information. INFO: 1. Highlight [Long Range] and push . The indicator illuminates.
Black plate (42,1) . [Map Scale]: Displays a scale on the left side of the screen. Use this to change the scale of a map. INFO: 2. Adjust the BirdviewTM angle by pushing the main directional buttons or rotating the center dial. 3. Push
Black plate (43,1) . 1. Push while the current location map screen is displayed. Rest Area Other settings: The map icons can also be set by performing the following procedure. 2. Highlight [Map Icons] and push . 4. Push
Black plate (44,1) . Map scrolling information [Latitude/Longitude Info] Information about the location, on which the center of the cross pointer is placed by scrolling on the map, can be set to be displayed. 1. Push . 4. Highlight [Map Scrolling Information] and push . 6. Push
Black plate (45,1) INFO: . [Map View]: Performs map operations such as the switching of map type and the setting of map orientation and scale. “MAP SETTINGS” page 2-4 . [Map Icons]: Displays map icons of certain points of interest (such as restaurants and gas stations, etc.) on the map around the current vehicle location. “Displaying map icons” page 2-16 . [Store Tracking]: Stores in the Address Book the route travelled from the starting point to the current location.
Black plate (46,1) . [Nearby Places]: Searches for points of interest near the map location where was pushed and sets them as a destination or waypoint. INFO: Incident details are a feature of Traffic Information, and an XM NavTraffic® subscription is required in order to receive Traffic Information. Use the same search method as the one for [Places]. “Finding nearby place” page 2-26 . [Store Location]: Store the map location where was pushed in the Address Book.
Black plate (47,1) MAP SYMBOLS This navigation system uses symbols to display facilities.
Black plate (48,1) Road color The road types are differentiated by colors. Freeway: (Red or light red (zoomed in)) Main road: (Brown or dark yellow) Narrow street: (Gray) Road with incomplete map data: (Dark green) Traffic information on map Incident With a subscription to the XM NavTraffic® service, traffic information is displayed.
Black plate (49,1) SETTING DESTINATION DESTINATION SCREEN . There are several methods that can be used to set a destination. Understand the advantages of each method and select the best method for finding and setting a preferred destination. Home: Searches for a route from the current location to the previously stored home destination. . Address Book: Searches for a destination from the list of the stored locations. . Previous Destinations: Searches for a destination from the previous destinations.
Black plate (50,1) Changing region Available setting items When setting a destination, the location can be narrowed down by specifying the region or city. . US1: CA, NV . US2: AZ, CO, ID, MT, NM, OR, UT, WA, WY . US3: IA, KS, MN, MO, ND, NE, SD . US4: AR, LA, MS, OK, TX . US5: IL, IN, MI, WI . US6: DC, DE, KY, MD, OH, PA, VA, WV . US7: CT, MA, ME, NH, NJ, NY, RI, VT . US8: AL, FL, GA, NC, SC, TN . US9: AK . US10: HI . Canada Specifying region: 1. Push . 2.
Black plate (51,1) address, and when [City] is highlighted and is pushed on the screen. “FINDING ADDRESS” page 2-25 . Highlight [Last 5 Cities] and push to display the last 5 cities recently set as destinations. FINDING ADDRESS When the address of the destination is known, use the following method to enter the address and then have the system calculate a route.
Black plate (52,1) 5. The entire route is shown on the map. Highlight [Start] after confirming the location of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route. INFO: In some cases, when a street name has been entered, the number of matching destinations in the “Matches” column may be different from the number displayed on the list screen. If this occurs, enter more characters to further reduce the number of matches.
Black plate (53,1) the selected location is displayed in the preview on the right side of the screen. INFO: 3. Highlight the preferred nearby category from the list and push . A list screen is displayed. . A maximum of 100 facilities can be displayed on the list screen. . If the suggested route is already set, the system displays the facilities located along the route. To display all the icons, deactivate [Show Along Route].
Black plate (54,1) Searching by other methods 1. Push . 2. Highlight [Places] and push . 4. Set the narrowing down conditions for the landmarks and push . INFO: Highlight [Change Region] and push to change the region. A screen for selecting a region is displayed. “Changing region” page 2-24 INFO: If [Select a City] is highlighted and is pushed, a city name input screen is displayed. Specify the city to be searched before narrowing down the categories.
Black plate (55,1) INFO: after entering the first facility name. Subcategories may not exist depending on the category that is selected. INFO: To select a category by directly inputting the category name, highlight [Category Search] and push . The category name input screen is displayed. INFO: 7. Enter the name of the destination facility and highlight [List], and then push . The facility list is displayed.
Black plate (56,1) INFO: . . . By highlighting [Sort] and pushing , options can be sorted from [By Name] or [By Dist.]. When selecting [By Dist.], the position of the selected location is displayed in the preview on the right side of the screen. In some cases, when a facility name has been entered, the number of matching destinations in the “Matches” column may be different from the number displayed on the list screen. If this occurs, enter more characters to further reduce the number of matches.
Black plate (57,1) 5. Highlight the preferred city and push . A list screen is displayed. 7. Highlight the preferred category and push . A list screen is displayed. 9. Highlight the preferred destination facility from the list, and then push . INFO: 6. Highlight [RESTAURANT] and push . A list screen is displayed. 8. Highlight the preferred sorting order and push . A list screen is displayed. .
Black plate (58,1) C 2009 Zagat Survey, LLC. Zagat Survey is a * registered trademark of Zagat Survey, LLC. SETTING HOME AS DESTINATION The home location can be set as the destination to which the system calculates a route. This function is especially useful when searching for a route to return to the home location. 3. The home location is displayed, and the system sets the home location as the destination.
Black plate (59,1) To set the home location as the destination: “Navigation” “Home” (Standard Mode) “Home” (Alternate Command Mode) INFO: SEARCHING FROM ADDRESS BOOK Storing frequently used destinations in the Address Book makes it easy for the system to set and calculate a route. To utilize this function more effectively, destinations that are often traveled to should be stored in advance. 3. Highlight the preferred location from the list and push .
Black plate (60,1) to the selected location and starts calculating a route. INFO: Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc. “PROCEDURES AFTER SETTING DESTINATION” page 2-43 SETTING PREVIOUS DESTINATION It is possible to set the destination to a location that has been previously set as a destination and have the system calculate a route. Up to 300 previous destinations will be automatically stored.
Black plate (61,1) of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route. SETTING PREVIOUS START POINT It is possible to set the destination to the start point of a previous route guidance and have the system calculate a route. INFO: Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc. “PROCEDURES AFTER SETTING DESTINATION” page 2-43 Setting by voice command 1.
Black plate (62,1) To set a previous start point as the destination: “Previous Start Point” (Alternate Command Mode) INFO: TER>. A list screen is displayed. . Even after setting a destination, the location of the destination can be adjusted, the location can be stored, etc. “PROCEDURES AFTER SETTING DESTINATION” page 2-43 . The stored route includes only locations (destination and waypoints) and route calculation conditions, not the route itself.
Black plate (63,1) phone number. Residential phone numbers cannot be used to search for a location. A confirmation screen for the place name and the location is displayed, and the system starts calculating. 4. Enter the telephone number including the area code. 1. Push . 2. Highlight [Next Page] and push . 5. After finishing the entry, highlight [List] and push . “NUMBER INPUT SCREEN” page 117 7. The entire route is shown on the map.
Black plate (64,1) SETTING FREEWAY ENTRANCE/ EXIT It is possible to set the destination to an entrance or exit of a freeway and have the system calculate a route. 4. Enter the name of the freeway. 5. After finishing the entry, highlight [List] and push . 7. Highlight [Entrance] or [Exit] and push . A list screen is displayed. 1. Push . 2. Highlight [Next Page] and push . 6. Highlight the freeway of the destination from the list, and push . 8.
Black plate (65,1) INFO: Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc. “PROCEDURES AFTER SETTING DESTINATION” page 2-43 SETTING INTERSECTION INFO: It is possible to set an intersection of any two streets as the destination and have the system calculate a route. Select [By Distance] to sort the list by the nearest distance. 3. Highlight [Intersection] and push . A character input screen is displayed. 1. Push . 2.
Black plate (66,1) INFO: Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc. “PROCEDURES AFTER SETTING DESTINATION” page 2-43 SETTING CITY CENTER 5. Highlight a street as the 1st street from the list and push . A character input screen is displayed. 7. Highlight a street as the 2nd street from the list and push . 6. Enter the name of the 2nd street. After finishing the entry, highlight [List] and push .
Black plate (67,1) INFO: Highlight [Last 5 Cities] and push to display the last 5 cities recently set as destinations. 3. Highlight [City Center] and push . A character input screen is displayed. INFO: Select [By Distance] to sort the list by the nearest distance. 5. Highlight the preferred destination from the list and push . The position of the selected location is displayed in the preview on the right side of the screen. 4.
Black plate (68,1) INFO: can be set as a destination. route. Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc. “PROCEDURES AFTER SETTING DESTINATION” page 2-43 SETTING POINT ON MAP It is possible to set a location scrolled to on the map as the destination and have the system calculate a route. 2. Highlight [New Dest.] and push . INFO: For the items other than [New Dest.], refer to “Map menu screen”.
Black plate (69,1) ROUTE GUIDANCE 2. Select [Delete Destination] and press . PROCEDURES AFTER SETTING DESTINATION After performing a route search, the route guidance can be immediately started. Also, it is possible to confirm or change a route. 3. A confirmation message is displayed. Select [Yes] and press . The destination and the waypoints are deleted. INFO: 1. Push < > on the steering wheel. 2. After the tone sounds, speak a command.
Black plate (70,1) “Editing route” page 2-55 . Selecting route Even if the map screen is touched or directional buttons other than the up or down button are pushed, the same map screen as when [Move Location] is selected is displayed. Starting route guidance Available route conditions . [Short. Time] (purple): Prioritizes by the shortest time. . [Min. Freeway] (orange): Minimizes the use of freeways. . [Short. Dist.] (green): Prioritizes by the shortest distance. INFO: 1.
Black plate (71,1) Confirming route Available information Adding destination or waypoint: . [Turn List]: Displays the details of the suggested route. “Using turn list” page 2-60 Before starting route guidance, destinations and/or waypoints can be added. A total of 6 destinations or waypoints can be set. . [Preview]: The system will trace the planned route going forward or in reverse. “Using route preview” page 2-61 . [Add Way Pt.]: Edits the route by adding a waypoint or a destination.
Black plate (72,1) . If a destination was added, the prior destination becomes a waypoint. Moving location of destination The location of the destination can be adjusted by moving the cross pointer across the map. 3. Highlight [Add Destination] or [Add Waypoint] and push . 2. Adjust the location by moving the cross pointer across the map and push . The location of the destination is modified. INFO: 1. Highlight [Move Location] and push . INFO: 4.
Black plate (73,1) Storing location A searched location can be stored in the Address Book. Then it can be easily retrieved and set as a destination (or waypoint). Viewing information about searched location Information (street address and phone number) about places stored in the map data can be displayed. INFO: . If [Call] is displayed on the right side of the screen, it is possible to call the location indicated. .
Black plate (74,1) Voice guidance during route guidance When approaching a guide point (intersection or corner), destination, etc. during route guidance, voice guidance announces the remaining distance and/or turning direction. Push to repeat voice guidance. Example of voice guidance: 1 * 2 * “In about one quarter mile (400 meters), right (left) turn.” “Right (left) turn ahead.” “In about one quarter mile (400 meters) freeway entrance on your right onto (road number and direction).
Black plate (75,1) Guidance screens and preview mode Enlarged intersection view: Junction guidance: When approaching a guide point, the system automatically changes to the split screen and shows an enlarged view of the intersection on the left screen. After passing through the intersection, the system automatically returns to the full screen mode. To switch to the full screen mode while the enlarged intersection view is displayed, push
Black plate (76,1) Turn list: Guidance screen settings The guidance screen can be displayed at all times even when the vehicle is located away from the guide point. Various types of screens can be set. Split screen settings: The display setting on the left-hand side screen shown during route guidance can be changed. 3. Highlight [View Settings] and push . Depending on the setting, the system can constantly display the split screen and show the turn list on the left screen.
Black plate (77,1) . Turn list . Fuel Economy NOTICE Use the values displayed on the fuel economy screen as a guide. When the fuel gauge indicates “E” (Empty) or the low fuel warning light illuminates even if the distance to empty reading indicates a sufficient amount of fuel remains, refuel the vehicle as soon as possible. The list screen for showing the guide points to the destination and the map screen can be displayed at the same time.
Black plate (78,1) Show exit information on freeways: information will be shown in the turn list. The exit information is shown as icons. When the vehicle travels on a highway or a toll road, the display automatically provides exit information in the turn list. 4. Highlight [Show all Freeway Exits on Route] or [Auto. Show Turn List on Freeway] and push . The indicator illuminates when the item is set. 1. Push while the current location map screen is displayed. 5.
Black plate (79,1) ROUTE SCREEN WARNING Always stop the vehicle in a safe location before modifying the route conditions. Modifying the route conditions while driving may cause an accident. 1. Highlight the exit where the exit information icon is displayed, and push . The category list screen is displayed. 2. Highlight the landmark category and push . The list screen for showing facilities located near the freeway exit is displayed. 3.
Black plate (80,1) . [Detour]: A detour of a specified distance can be calculated. “Setting detour route” page 2-63 . [Edit/Add to Route]: Edit or add a destination or waypoints to the route that is already set. “Editing route” page 2-55 [Traffic Detour]: Manually search for an alternative detour route taking the traffic information into consideration. “Searching for detour route taking traffic information into consideration” page 2-64 . .
Black plate (81,1) Setting by voice command 1. Push < > located on the steering wheel. 3. A confirmation message is displayed. Highlight [Yes] and push . The canceled route is reactivated. 2. After the tone sounds, speak a command. To cancel a route: “Cancel Route” (Alternate Command Mode) Reactivating route: INFO: If a new route is set, the canceled route cannot be reactivated. Editing route Available setting items 1 * 2 * 1. Push . 2. Highlight [Resume Route] and push .
Black plate (82,1) 6 * 7 * “Editing/deleting destination or waypoint” page 2-57 2. Highlight [Edit/Add to Route] and push . Condition for calculating a route to a waypoint: Changes the conditions for calculating a route to a waypoint. “Changing route calculation conditions” page 2-59 [Calculate]: Manually search for the route again after changing the search conditions and have the system calculate a route. “Changing route calculation conditions” page 2-59 3.
Black plate (83,1) INFO: . The prior route is automatically deleted. . Added waypoints and search conditions will not be taken into consideration for the route calculation until [Calculate] is highlighted and is pushed. already set and push . Editing/deleting destination or waypoint: The destination or waypoint that has already been set can be modified or deleted.
Black plate (84,1) INFO: . If the destination is deleted, the final waypoint of the route becomes the destination. . Even if the map screen is touched, the same map screen as when [Move Dest.] is selected is displayed. Changing order of destination and waypoints: The order of a destination and waypoints that have already been set can be changed. 1. Push . 2. Highlight [Edit/Add to Route] and push . 4. Highlight [Change Order] and push .
Black plate (85,1) Changing route calculation conditions: Each section of the route between waypoints can have different route calculation conditions. After setting these conditions, the entire route can be recalculated. Available conditions : [Fastest Route] : [Minimize Freeway] : [Shortest Route] 1. Push . 2. Highlight [Edit/Add to Route] and push . 3. Highlight the preferred section of the route to the destination or waypoint and push .
Black plate (86,1) Confirming route Available setting items When the suggested route is displayed after calculation, the route information can be confirmed or the suggested route can be simulated. . [Turn List]: Displays the details of the suggested route. “Using turn list” page 2-60 . [Preview]: The system will trace the planned route going forward or in reverse. “Using route preview” page 2-61 . [Simulation]: Displays a simulation of the suggested route.
Black plate (87,1) Using route preview: Confirming route by simulation: Guidance settings Various guidance settings can be set. 1. Highlight [Preview] and push . 1. Highlight [Simulation] and push . 2. Highlight the preferred key and push . 2. Highlight the preferred key and push . Basic operation: 1. Push . : Moves forward in the direction of the destination. : Pauses the simulation. 2. Highlight [Guidance Settings] and push .
Black plate (88,1) Recalculate route A route can be manually searched again after changing the search condition. When the vehicle deviates from the suggested route, the route from the current location to the destination is automatically searched again. 3. A message is displayed, and the route is recalculated. Manually re-searching route: Available setting items . [Guidance Voice]: Activates or deactivates voice guidance. The indicator illuminates if voice guidance is activated. .
Black plate (89,1) Setting Auto Reroute: 1. Push . 2. Highlight [Route Settings] and push . 2. Highlight [Detour] and push . 4. Highlight [Auto Reroute] and push . The indicator illuminates. When the current location map screen or route setting screen is displayed, the system recalculates a route with the set conditions. “Detailed route settings” page 2-66 3. Highlight a detour distance and push .
Black plate (90,1) Searching for detour route taking traffic information into consideration When a serious traffic event occurs on the route, or if the system finds a faster route, a detour alert will pop up automatically. If the automatic alert is not noticed, a detour can also be manually searched. 3. When the detour search is successful, detailed information about the detour route (left screen) and the comparison screen of the two routes (right screen) are displayed.
Black plate (91,1) INFO: . . If no operation is performed for one minute after the message is displayed, the message disappears. The detour will not be accepted, and the current suggested route will remain unchanged. Setting conditions for route calculation Search condition settings: The route can be recalculated after changing the route calculation conditions anywhere along the route.
Black plate (92,1) Detailed route settings: Available setting items Detailed conditions can be set for the route calculation. . [Minimize Toll Roads]: Minimizes the use of toll roads. . [Use Time Restricted Roads]: Uses any roads subject to time restrictions. . [Use Statistical Traffic Information]: Uses statistical traffic information that is stored in the map data. . [Use Real Time Traffic Information]: Uses the latest traffic information received via the XM broadcast. 1. Push .
Black plate (93,1) accidents, construction work, traffic restrictions, emergencies, etc., the prediction accuracy of the system may be reduced. . Traffic jam information displayed on the map screen is not statistical traffic information. . When [Use Statistical Traffic Information] is turned on, the system may lead to a road where a traffic jam occurs or to a detour even though the shortest route does not have a traffic jam. .
Black plate (94,1) “ROUTE GUIDANCE SETTINGS” page 2-67 . [Guidance Display Settings]: Activates or deactivates small turn arrow display on the map. “Displaying small turn arrow on map” page 2-69 . [Estimated Time]: Switches the display of the estimated travel time to the destination or waypoint that is displayed on the map screen. “Switching estimated arrival time display” page 2-69 .
Black plate (95,1) voice guidance: “Turning Point” and “1 Guide”. [Turning Point]: Turns on the sound that chimes when a maneuver is supposed to be occurring. Example: Switching the display to the travel time to the waypoint Displaying small turn arrow on map 3. Highlight [Guidance Settings] and push . . 1. Push . 2. Highlight [Navigation] and push . The guidance screen displayed when the vehicle passes through an intersection can be changed. 5.
Black plate (96,1) Set average speeds The required time to the destination can be calculated based on the set vehicle speeds. or to activate the setting. 9. Push to return to the previous screen. Push
Black plate (97,1) STORING A LOCATION/ROUTE [−]. STORING LOCATION . [Town Road]: Adjust the average vehicle speed on a town road by moving the main directional buttons or the center dial in the direction of [+] or [−]. Often visited locations can be stored in the Address Book. The stored addresses can be easily retrieved to set them as a destination or waypoint. .
Black plate (98,1) INFO: 5. Highlight [Home Location (None)] or [Add New] and push . 7. When a preferred location is displayed at the center of the map, confirm the address of the location and push . A message is displayed, and the address of the location is stored in the Address Book. 6. Highlight the appropriate method to search for a location and push . “SETTING DESTINATION” page 2-23 8. Adjust the location of the stored item and edit the contents of the stored item as necessary.
Black plate (99,1) 5. Highlight the appropriate method to search for a location and push . The address of the searched location is stored. “SETTING DESTINATION” page 2-23 TER>. A message is displayed, and the current vehicle location is stored in the Address Book. Storing location by moving map Storing current vehicle location 1. Move to the preferred location on the map and push . 4. The icon representing the stored location is displayed on the map. 1.
Black plate (100,1) 3. The icon representing the stored location is displayed on the map. 2. Highlight [Route Info] and push . Push
Black plate (101,1) TER>. 4. Highlight [Stored Routes] and push . 5. Highlight [Store Current Route] and push . 6. A confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . The current route is stored. INFO: . The route is stored in the first available position number in the store current route list. . A maximum of 5 routes can be stored. When 5 routes are stored in the Address Book, a new route cannot be stored until a route is deleted.
Black plate (102,1) . The tracked route is stored in the first available position number in the store tracking list. INFO: Other settings A tracked route can only be stored using the setting screen when [Current Tracking] is set to on. A tracked route can also be stored using the following procedure. STORING AVOID AREA An Avoid Area can be stored. The Avoid Area is an area that can be excluded from a route, such as a road that is always congested.
Black plate (103,1) 6. Highlight the appropriate method to search for a location and push . “SETTING DESTINATION” page 2-23 . [Delete]: Deletes the avoid area. “Delete” page 2-88 8. After finishing the setting, highlight [OK] and push . EDITING ADDRESS BOOK Items stored in the Address Book can be modified. These settings can be edited to make the navigation system more useful. 5. Highlight [Add New] and push . INFO: A maximum of 10 Avoid Areas can be stored.
Black plate (104,1) Available setting items . [Stored Location]: Edits the information of a stored home and Address. “Editing stored home and address” page 2-78 . [Stored Routes]: Edits the information of a stored route. “Editing stored route” page 2-84 . [Stored Tracking]: Edits the information of a stored tracked route. “Editing stored tracking” page 2-84 . [Avoid Area]: Edits the information of a stored Avoid Area. “Editing avoid area” page 2-86 .
Black plate (105,1) Minor adjustment of home or stored address When [Edit] is selected, you can edit the following items of the home or stored location can be edited. 1. Push . 2. Highlight [Address Book] and push . 3. Highlight [Store/Edit] and push . . [Show Icon on Map]: . [Name] (only for stored locations): . [Voicetag] (only for stored locations): . [Icon]: . [Sound]: . [Direction]: . [Distance]: . [Phone No.]: . [Group] (only for stored locations): .
Black plate (106,1) Name (only for stored locations): Voicetag (only for stored locations): Changes the name of a stored location. 1. Highlight [Voicetag] and push . 3. A beep sounds, and the system enters the voice command reception mode. 4. Speak the name/word to be used as Voicetag. 1. Highlight [Name] and push . A character input screen is displayed. 5. The Voicetag is stored, provided the system recognizes it. INFO: 2. Highlight [Store] and push . 2.
Black plate (107,1) . If a Voicetag is already stored, select [Restore] to re-record the Voicetag. 2. Highlight the preferred icon and push . . The indicator of the selected alarm tone illuminates. Icon: 3. The icon is changed. Changes the icon of the home or stored address to the preferred one. By changing the icons, the usage of the [By Icon] option of the sort function can be optimized more effectively ([Sort] menu situation).
Black plate (108,1) 2. Set the direction that sounds the alarm and push . The selected direction is set. INFO: After the direction is set and [Direction] is selected and set again, a confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . The set direction is overwritten. Distance: Sets the alarm to sound when reaching a specific distance to the home or stored address. 2. Highlight the preferred distance option and push .
Black plate (109,1) INFO: TER>. If the phone number of the home or a location is stored, the phone number can be used to search for the destination even if it is not included in the map data. A list of stored locations is displayed. Group (only for stored locations): This groups the stored locations. By grouping the stored locations, the [By Group] option of the sort function can be used more effectively in the [Sort Entries] mode. 2. Highlight the preferred group and push .
Black plate (110,1) Editing stored route INFO: Editing stored tracking If [Store Current Route] is selected, the system stores the current route. Available setting items 1. Highlight [Stored Routes] and push . 2. Highlight the preferred stored route and push . . [Rename]: Changes the name. “CHARACTER (letters and numbers) INPUT SCREEN” page 1-16 . [Replace]: Overwrites the stored route to the current route. . [Delete]: Deletes the stored route. . [OK]: Applies the settings. 1.
Black plate (111,1) 3. Highlight the preferred item and push . Available setting items (Current tracking) . [Replace]: Overwrites the stored tracked route to the current tracked route. . [Delete]: Deletes the stored tracked route. . [OK]: Applies the settings. . [View Track]: Displays the tracked route up to the current location. . [Delete]: Deletes the stored current tracking. Displaying a tracked route: . [OK]: Applies the settings.
Black plate (112,1) Editing avoid area 1. Highlight [Avoid Area] and push . 2. Highlight the preferred Avoid Area and push . . [Move Location]: Adjusts the location of the Avoid Area. . [Resize Area]: Adjusts the range of the Avoid Area. . [FWY]: Avoids freeways. . [Delete]: Deletes the Avoid Area. . [OK]: Applies the setting. 4. After finishing the setting, highlight [OK] and push . INFO: An Avoid Area can be added by selecting [Add New].
Black plate (113,1) Move Location: Resize Area: FWY: Adjusts the location of the Avoid Area. Adjusts the range of the Avoid Area. Sets the route to avoid freeways. 1. Highlight [Move Location] and push . 1. Highlight [Resize Area] and push . 1. Highlight [FWY]. 2. Adjust the location of the Avoid Area. 2. Highlight the range from 5 available levels. 3. After adjusting the location, push . 3. After highlighting the range, push .
Black plate (114,1) INFO: If the current vehicle location is set to an Avoid Area, the system will not provide route guidance. Delete: Deletes the Avoid Area. DELETING STORED ITEM The locations and routes in the Address Book can be deleted. Two deletion methods are available: deleting an individual item and deleting all stored items. NOTICE Deleted items cannot be restored. Before deleting an item, always make sure that the item is truly not necessary. 3. Highlight [Address Book] and push .
Black plate (115,1) 3. Highlight [Store/Edit] and push . 4. Highlight [Edit or Delete an Entry] and push . 5. Highlight a preferred address and push . “SETTING DESTINATION” page 2-23 INFO: 5. Highlight the preferred location/route for deletion and push . 7. A confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . The stored item is deleted from the Address Book.
Black plate (116,1) Deleting individual item on map Deleting all stored items 1. Align the cross pointer over the preferred stored location for deletion by moving on the map. Then push . 1. Push . 4. Highlight [Delete Stored Items] and push . 2. Highlight [Navigation] and push . 2. Highlight [Delete] and push . 3. Highlight [Address Book] and push . 3. A confirmation message is displayed.
Black plate (117,1) . [Delete Stored Routes]: Deletes all stored routes. . [Delete Current Tracking]: Deletes the current tracked route. . [Delete Stored Tracking]: Deletes all stored tracked routes. . [Delete Avoid Areas]: Deletes all stored Avoid Areas. . [Delete Stored Voicetags]: Deletes all stored Voicetags. . [Delete Previous Destinations]: Deletes all or one of the previous destinations. . [Delete Previous Start Point]: Deletes all previous start points. .
Black plate (118,1) 3. Highlight [Address Book] and push . 5. Highlight [Download Address Book to USB] or [Download Address Book from USB] and push . 7. Highlight [Download] and push . NOTICE Do not remove the USB memory until the system completely imports or exports the data. 4. Highlight [Transfer Address Book] and push . 6. Highlight a stored item. The [ON] indicator illuminates.
Black plate (119,1) NAVIGATION SETTING displayed. Once overwritten, the original data cannot be recovered. . [Map Icons]: Set the map icons to display on the map. “Displaying map icons” page 2-16 . [Guidance Settings]: Set the various functions for the route guidance. “Guidance settings” page 2-61 . [Route Settings]: Change the routing preferences. “Detailed route settings” page 2-66 . [Traffic Info Settings]: Set the various functions of the XM NavTraffic® information system.
Black plate (120,1) . [Delete Stored Information]: Delete stored locations and the home setting in the Address Book. “DELETE STORED ITEMS” page 2-98 . [Delete All Previous Destinations]: Delete all previous destinations. “DELETE STORED ITEMS” page 2-98 . [Delete Previous Starting Point]: Delete all previous starting points. “DELETE STORED ITEMS” page 2-98 . [Reset All Navigation Settings to Default]: Reset all of the settings to default.
Black plate (121,1) . [Map Scrolling Information]: Sets the system so that when the map scrolls the information about the location aligned at the center of the cross pointer is displayed. “Map scrolling information” page 2-18 . [Customize Nearby Places]: Set the category of frequently visited landmarks. “Customizing Nearby Places” page 295 . [Keyboard Type]: Switches the keyboard layout for the character input screen. “Settings keyboard layout of character input screen” page 2-96 . .
Black plate (122,1) 1. Highlight [Others] and push . 2. Highlight [Keyboard Type] and push . 3. Highlight the preferred item and push . The main category list is displayed. 5. Highlight a sub category and push . The category setting is modified. 6. Push
Black plate (123,1) while in a location where the GPS signals can be received. This may correct the position of the vehicle icon. “VEHICLE ICON” page 11-4 icon, push . QWERTY layout Adjusting current vehicle location If the vehicle icon indicating the current vehicle location is not in the correct position, the location of the vehicle icon on the map screen can be adjusted. INFO: .
Black plate (124,1) DELETE STORED ITEMS Delete stored item from setting screen. RESET ALL NAVIGATION SETTINGS TO DEFAULT This restores various settings (display, volume level, etc.) to the default settings. INFO: The memory contents, such as the stored locations, will not be deleted. 3. A confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . Basic Operation 1. Highlight [Navigation] and push . 2.
Black plate (10,1) 3 Audio system Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Audio operation precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 FM-AM-SAT radio with Compact Disc (CD) player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black plate (128,1) AUDIO SYSTEM AUDIO OPERATION PRECAUTIONS Radio Push the ignition switch to the ACC or ON position and push the radio band select button to turn on the radio. If you listen to the radio with the engine not running, the ignition switch should be pushed to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other external influences.
Black plate (129,1) many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely. Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights. . The player may skip while driving on rough roads. Satellite radio reception: .
Black plate (130,1) . . abnormal edges This audio system can only play prerecorded CDs. It has no capabilities to record or burn CDs. temperature is extremely high. Decrease the temperature before use. Only use high quality 4.7 in (12 cm) round discs that have the “COMPACT disc DIGITAL AUDIO” or “DVD Video” logo on the disc or packaging. . Do not expose the CD/DVD to direct sunlight. .
Black plate (131,1) . regions. Use DVDs with a region code “1”, “ALL” or “1 included” for your DVD entertainment system. (The region code A is displayed as a small symbol * B .) printed on the top of the DVD * This vehicle-installed DVD player cannot play DVDs with a region code other than “1” or “ALL”. have abnormal edges — This audio system can only play prerecorded CD/DVDs. It has no capabilities to record or burn CD/DVDs.
Black plate (132,1) midify or ventilate the USB player completely. . The USB player sometimes cannot function when the passenger compartment temperature is extremely high. Decrease the temperature before use. . Do not leave USB memory in a place prone to static electricity or where the air conditioner blows directly. The data in the USB memory may be damaged. . The vehicle is not equipped with a USB memory stick. . A USB device cannot be formatted with this system.
Black plate (133,1) files were written by the writing software, so the files might not play in the desired order. The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file. . Sampling frequency — Sampling frequency is the rate at which the samples of a signal are converted from analog to digital (A/D conversion) per second. . Multisession — Multisession is one of the methods for writing data to media.
Black plate (134,1) Specification chart: Supported media CD, CD-R, CD-RW, DVD-ROM, DVD+R, DVD+RW, DVD+R DL, USB2.0 CD, CD-R, CD-RW, DVD-ROM, DVD+R, DVD+RW, DVD+R DL: ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. * Files saved using the Live File System component (on a Windows Vista-based computer) are not supported. UDF Bridge (UDF1.02+ISO9660), UDF1.5, UDF2.0 * VDF1.5/VDF2.0 (packet writing) is not supported.
Black plate (135,1) *1 *2 *3 *4 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played. Protected WMA files (DRM) cannot be played. Available codes depend on what kind of media, versions and information are going to be displayed. When VBR files are played, the playback time may not be displayed correctly.
Black plate (136,1) Compressed Video Files Explanation of terms: . DivX® - DivX® refers to the DivX® codec owned by DivX, Inc. used for a lossy compression of video based on MPEG-4. . AVI - AVI stands for Audio Video Interleave. It is a standard file format originated by Microsoft Corporation. A “.divx” encoded file can be saved into the “.avi” file format for playback on this system if it meets the requirements stated in the table in this section. However, not all the “.
Black plate (137,1) Bluetooth streaming audio Distribution Profile (A2DP, AVRCP). . Some Bluetooth® audio devices may not be recognized by the in-vehicle audio system. . Bluetooth® . It is necessary to set up the wireless connection between a compatible Bluetooth® audio device and the in-vehicle Bluetooth® module before using the Bluetooth streaming audio. Music Box . . . . . Operating procedure of the Bluetooth streaming audio will vary depending on the device.
Black plate (138,1) ANTENNA FM-AM-SAT RADIO WITH COMPACT DISC (CD) PLAYER Adjusting tone quality and speaker balance: The satellite radio mode requires an active XM Satellite Radio subscription. The satellite radio is not available in Alaska, Hawaii and Guam. To adjust Bass, Treble, Balance and Fade, push the Audio control knob. When the display shows the setting you want to change (Bass, Treble, Balance and Fade), rotate the Audio control knob to set the desired setting. “AUDIO SETTINGS” page 7-3.
Black plate (139,1) XM satellite radio band select: Pushing will change the band as follows: SEEK tuning/CATEGORY (CAT): . XM1 ? XM2 ? XM3 ? XM1 When or is pushed while the ignition switch is in the ACC or ON position, the radio will come on at the channel last played. The last channel played will also come on when the ON·OFF button is pushed to ON. The satellite radio is not available in Alaska, Hawaii and Guam.
Black plate (140,1) List (AM and FM radio): . When [List] on the display is selected while the FM or AM radio is being played, the preset station list will be displayed. If 1 of the 6 preset stations listed is touched and held, the current station will be stored as the new preset. Menu (XM Satellite Radio): When [Menu] on the display is selected while the XM Satellite Radio is being played, the menu list will be displayed.
Black plate (141,1) . — 1 Folder Repeat (for CD with compressed audio files) — 1 Track Repeat — 1 Disc Random — 1 Folder Random (for CD with compressed audio files) Record to Music Box (for CD) Select to choose specific songs on the CD to record to the Music Box. . . . Disc title . Track title CD with compressed audio files: . Folder title . File title . Song title Title Text Priority (for CD) .
Black plate (142,1) DVD (DIGITAL VERSATILE DISC) PLAYER OPERATION Precautions CAUTION . Only operate the DVD while the vehicle engine is running. Operating the DVD for extended periods of time with the engine OFF can discharge the vehicle battery. . Do not allow the system to get wet. Excessive moisture such as spilled liquids may cause the system to malfunction. Start the engine when using the DVD entertainment system.
Black plate (143,1) item from the displayed video. When the operation screen is being shown, use the center dial or touch screen to select an item from the displayed menus. PAUSE: Select [ ] to pause the DVD. To resume playing the DVD, use [PLAY]. PLAY: / Next/Previous Image: This function is only for DVD-AUDIO. Select ] or [ ] to advance or rewind the still [ image. The still image will advance or rewind the number of times this key is selected.
Black plate (144,1) Angle (DVD-VIDEO): If the DVD contains different angles (such as moving images), the current image angle can be switched to another one. Select [Angle]. The angle will change each time the [+] side or [−] side is selected. DVD top menu language will be changed to the one specified. Display: To adjust the image quality of the screen, select the preferred adjustment items.
Black plate (145,1) the current track on the USB memory will be played. The center dial can also be used to select tracks when the USB memory is being played. Folder selection: To change to another folder in the USB memory, turn the folder selector or choose a folder displayed on the screen using the center dial. File selection Audio file operation When there are both audio and movie files in the USB memory, the mode select screen is displayed. Select the preferred contents to play.
Black plate (146,1) Pause ] to pause the movie file. To resume Select [ ]. playing the movie file, select [ Play ] to start playing a movie file, for Select [ example, after pausing a movie file. Menu: Movie file operation There are some options available during playback. Select one of the following options that are displayed on the screen if necessary. Refer to the following information for each item.
Black plate (147,1) . Display To adjust the image quality of the screen, select the preferred adjustment items. . DRC (Dynamic Range Compression) automatically adjusts the soundtrack volume level to maintain a more even sound to the speakers. Example Settings: . Select [Settings] to adjust the following settings. . Audio File Playback Switch to the audio playback mode. This item is displayed only when the USB memory contains the audio files. .
Black plate (148,1) Regulatory information FCC Regulatory information: — CAUTION: To maintain compliance with FCC’s RF exposure guidelines, use only the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations.
Black plate (149,1) Audio main operation Push the ignition switch to the ACC or ON position. Then, push repeatedly to switch to the Bluetooth audio mode. If the system has been turned off while the Bluetooth audio device was playing, pushing the ON·OFF/ VOL control knob will start the Bluetooth audio device. 3. A confirmation screen will be displayed. Select [No]. Note: Selecting [Yes] will only connect the hands free phone portion of a Bluetooth® device. 5.
Black plate (150,1) than 1.5 seconds while a Bluetooth® audio file is being played, the next track or the beginning of the current track on the Bluetooth audio device will be played. The center dial can also be used to select tracks when the Bluetooth® audio play mode screen is shown on the display. (“Bluetooth audio” will be indicated on the header of the screen.) Play Mode: Bluetooth: The play mode setting display will appear when [Menu] is selected.
Black plate (151,1) Edit Bluetooth Info: Change the name broadcasted by this system over Bluetooth. Change the PIN code that is entered when connecting a hands free device to this system. Replace Connected Phone: Replace the Bluetooth connection with a connected Bluetooth cellular phone. “Bluetooth® Hands-Free Phone System” page 4-1 iPod® PLAYER OPERATION Connecting iPod® Open the console lid and connect the cable to the USB connector.
Black plate (152,1) . Albums . Songs . Podcasts . Genres . Composers . Audiobooks . Shuffle Songs REPEAT (RPT), RANDOM (RDM): When is pushed while a track is being played, the play pattern can be changed as follows: Extreme temperature conditions [below −48F (−208C) and above 1588F (708C)] could affect the performance of the hard-disk. NOTICE If the audio system needs to be replaced due to a malfunction, all stored music data will be erased.
Black plate (153,1) . . The recording process can be stopped at any time. All tracks that were played before the CD was stopped are stored. . There is not enough space in-vehicle memory . The number of albums reaches the maximum of 500. Individual tracks can be deleted from the hard-disk drive after the CD is recorded. . The number of tracks reaches the maximum of 3,000. Playing recorded songs Select the “Music Box” audio system by using one of the following methods. .
Black plate (154,1) than 1.5 seconds while a track is being played, the next track or the beginning of the current track will be played. . The center dial can also be used to select tracks when a track is being played. . Play tracks from all recorded tracks. The tracks are sorted in alphabetical order.
Black plate (155,1) ing a track and specifying the order. . . Edit the “Track”, “Artist” and “Genre” information of the current track using the keypad displayed on the screen. “HOW TO INPUT LETTERS AND NUMBERS” page 1-16 Edit Name Edit the name of the Playlist using the keypad displayed on the screen. “HOW TO INPUT LETTERS AND NUMBERS” page 1-16 . . . Normal . 1 Album Repeat . 1 Track Repeat . 1 Playlist Random . 1 Artist Random . 1 Album Random .
Black plate (156,1) Delete Songs from Music Box: Deletes the current song, selected songs or albums by choosing from the list, or all songs/ albums in the Music Box. Recording Quality: Set the recording quality of 105 kbps or 132 kbps. The default is set to 105 kbps. CDDB Version: The version of the built-in Gracenote Database is displayed. Gracenote NOTICE . The information contained in the Gracenote Database is not fully guaranteed. .
Black plate (157,1) error-free or that functioning of Gracenote Software or Gracenote Servers will be uninterrupted. Gracenote is not obligated to provide you with new enhanced or additional data types or categories that Gracenote may provide in the future and is free to discontinue its services at any time. practice one or more of the following U.S. Patents: #5,987,525; #6,061,680; #6,154,773, #6,161,132, #6,230,192, #6,230,207, #6,240,459, #6,330,593, and other patents issued or pending.
Black plate (158,1) CAR PHONE OR CB RADIO sunlight. . Do not spill any liquids on the USB memory. Refer to the USB memory Owner’s Manual for the details. When installing a car phone or a CB radio in your NISSAN, be sure to observe the following cautions, otherwise the new equipment may adversely affect the electronic control modules and electronic control system harness. WARNING . . . A cellular telephone should not be used while driving so full attention may be given to vehicle operation.
Black plate (13,1) 4 Bluetooth® Hands-Free Phone System Bluetooth® Hands-Free Phone System . . . . . . . . . . . . . . . . . . . 4-2 Regulatory information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Voice commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Control buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Connecting procedure. . . . . . . . . . . . . . . . . . . . .
Black plate (162,1) BLUETOOTH® HANDS-FREE PHONE SYSTEM WARNING . . Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation. If you find yourself unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop your vehicle before doing so.
Black plate (163,1) . . . Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers. Storing the device in a different location may reduce or eliminate the noise. Refer to the cellular phone Owner’s Manual regarding the telephone pairing procedure specific to your phone, battery charging, cellular phone antenna, etc. The antenna display on the monitor will not coincide with the antenna display of some cellular phones.
Black plate (164,1) www.nissanusa.com/bluetooth or call NISSAN Consumer Affairs Department for instructions on pairing NISSAN recommended cellular phones. When the connection process is completed, the screen will return to the Phone menu display. PHONE SELECTION CONNECTING PROCEDURE 1. Push or < [Connect Phone]. >, and select Up to 5 cellular phones can be registered to the system. To switch to connect another cellular phone, push and select [Connected Phone].
Black plate (165,1) Select one of these entries to save in the vehicle phonebook. . [Copy from the Handset]: The system will show the connected cellular phone’s phonebook that was downloaded (depending on the phone’s compatibility). Select one of these entries to save in the vehicle phonebook. 1. Push and select [Vehicle Phonebook]. 2. Select [Add New] at the top of the screen. 5. Select [Voicetag] to record a name to speak when using NISSAN Voice Recognition system. 6.
Black plate (166,1) “Voice recognition” page 8-1 To delete an entry, select [Delete] at step 3. The following editing items are available: 5. Select [Call] to start dialing the number. . There are different methods to make a call. Select one of the following options instead of [Handset Phonebook] in step 2 above. [Entry #]: Changes the displayed number of the selected entry. . [Name]: Edit the name of the entry using the keypad displayed on the screen. .
Black plate (167,1) . [Reject Call]: . Reject an incoming call. To finish the call, perform one of the following procedures listed below. Mute your voice to the person. . c) Push < > on the steering wheel. When you hear a phone ring, the display will change to the incoming call mode. To receive a call, perform one of the following procedures listed below. b) Push on the instrument panel. > on the steering wheel. There are some options available when receiving a call.
Black plate (168,1) PHONE SETTING To set up the Bluetooth® Hands-Free Phone System to your preferred settings, push and select [PHONE]. Edit Vehicle Phonebook Phonebook registration and editing/deleting the registered phonebook can be performed. Delete Phonebook The vehicle phonebook entries can be deleted all at the same time or one by one. Download Handset Phonebook Download the contacts registered in a Bluetooth® cellular phone. Availability of this function depends on each cellular phone.
Black plate (16,1) 5 Heater and air conditioner Operation precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 How to view screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Automatic operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Cooling and/or dehumidified heating (AUTO) . . . . . . . . 5-2 Heating (A/C OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black plate (172,1) OPERATION PRECAUTIONS AUTOMATIC OPERATION COOLING AND/OR DEHUMIDIFIED HEATING (AUTO) WARNING . The air conditioner cooling function operates only when the engine is running. . Do not leave children or adults who would normally require the support of others alone in your vehicle. Pets should not be left alone either. On hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals. .
Black plate (173,1) HEATING (A/C OFF) The air conditioner does not activate in this mode. When you need to heat only, use this mode. 2. Operate the driver side temperature control dial to set the desired temperature. Adjust the temperature to about 758F (248C) for normal operation. . The temperature of the passenger compartment will be maintained automatically. Air flow distribution and fan speed will also be controlled automatically. 3.
Black plate (174,1) DEHUMIDIFIED DEFROSTING OR DEFOGGING . When the front defroster button < > is pushed, the air conditioner will automatically be turned on at outside temperatures above 238F (−58C) to defog the windshield, and the air recirculate mode will automatically be turned off. Outside air is drawn into the passenger compartment to improve the defogging performance. 2. Operate the temperature control dial to set the desired temperature. .
Black plate (175,1) MANUAL OPERATION FAN SPEED CONTROL Turn the fan speed control dial < manually control the fan speed. > to Push to return to automatic control of the fan speed. AIR RECIRCULATION OUTSIDE AIR CIRCULATION Push the intake air control button < > to recirculate interior air inside the vehicle. The ” will come on. indicator light “ Push the outside air circulation button < > to change the air circulation from the intake air to ” will the outside air.
Black plate (176,1) TO TURN THE SYSTEM OFF VENTILATORS AIR FLOW CONTROL Push . Pushing selects the air outlet to: : Air flows from center and side ventilators. : Air flows from center and side ventilators and foot outlets. : Air flows mainly from foot outlets. : Air flows from defroster and foot outlets. The direction of the air flow can be adjusted by A opening, * B closing or * C adjusting.
Black plate (177,1) OPERATING TIPS IN-CABIN MICROFILTER SERVICING AIR CONDITIONER The air conditioning system is equipped with an in-cabin microfilter which collects dirt, pollen, dust, etc. To make sure the air conditioner heats, defogs, and ventilates efficiently, replace the filter in accordance with the maintenance schedule in the NISSAN Service and Maintenance Guide. To replace the filter, contact a NISSAN dealer or GT-R certified NISSAN dealer.
Black plate (178,1) MEMO 5-8 Heater and air conditioner Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (19,1) 6 Viewing technical information Status screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Information screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Viewing information about current vehicle location. . . . . . 6-3 Basic operation . . . . . . . . . . . . . . . .
Black plate (180,1) STATUS SCREEN By pushing at any time, a split screen with audio information that is always at the top can be displayed. Each time is pushed, the bottom part of the screen changes between air conditioner, fuel economy and navigation directions.
Black plate (181,1) VIEWING INFORMATION ABOUT CURRENT VEHICLE LOCATION Available items . [Fuel Economy]: Displays the fuel economy information. “FUEL ECONOMY INFORMATION” page 6-4 . [Tire Pressure]: Displays the tire pressure information. “TIRE PRESSURE INFORMATION” page 6-5 . [Maintenance]: Displays the vehicle maintenance information. “MAINTENANCE INFORMATION” page 6-6 . [Where am I?]: Displays information regarding the current vehicle location.
Black plate (182,1) VEHICLE INFORMATION DISPLAY Contents of vehicle location information 1 * 2 * 3 * 4 * 5 * Next Street: Displays the next street on the route. Current Street: Displays the current street on the route. Previous Street: Displays the previous street on the route. Displays the distance to the next intersection on the route. FUEL ECONOMY INFORMATION The distance to empty, average fuel economy and current fuel economy (shown on the right side bar) will be displayed for reference.
Black plate (183,1) TIRE PRESSURE INFORMATION The tire pressure will be displayed for reference. The pressure indication “** psi” on the screen means that the tire pressure is being measured. After a few driving trips, the pressure for each tire will be displayed. In case of low tire pressure, LOW PRESSURE information will be displayed on the screen. Check the pressure for all tires. WARNING . .
Black plate (184,1) . TPMS malfunction MAINTENANCE INFORMATION The maintenance intervals can be displayed for your desired maintenance items. When the system displays the tire pressure as “**”, the pressure values for the tires are not displayed. INFO: When a tire malfunction occurs, a warning message will also be displayed in Vehicle Information. Setting by voice command 1. Push < > located on the steering wheel. 2. After the tone sounds, speak a command.
Black plate (185,1) VIEWING AVAILABLE TRAFFIC INFORMATION The maintenance reminder screen is displayed each time the ignition switch is pushed to the ON position unless one of the following operations is performed: The Reminder will be automatically displayed as shown when both of the following conditions are met: . . the vehicle is driven the set distance and the ignition switch is pushed to the LOCK position.
Black plate (186,1) . warning. Relying only on XM NavTraffic® information may lead to a collision and could result in serious personal injury. [Nearby Traffic Info]: Displays the list of traffic information around the current vehicle location. NOTICE Flow information is provided only for roads equipped with traffic sensors and is not available in all markets covered by the service. Flow data may not be available on portions of a road that is under construction.
Black plate (187,1) INFO ON ROUTE information, and push . This is only available when a route is set. The list of available traffic information around the current vehicle location is displayed. The list of traffic information found on the recommended route from the current vehicle location to the destination is displayed. The detailed information about displayed events can also be checked. 3. The map screen centered around the selected event is displayed.
Black plate (188,1) DISPLAY URGENT TRAFFIC INFORMATION When an urgent event is found around the current vehicle location, a message pops up automatically with a voice announcement. 3. The map screen centered around the selected event is displayed. On the left screen, the detailed information about the event is displayed. The message can be scrolled using the up/down button of directional switch or the steering wheel. 4. Push < screen. > to return to the previous INFO: .
Black plate (189,1) : Slippery road : Weather : Incident 4 * Screen information * 1 2 * 3 * Road conditions (Green) Free Flow: (Yellow) Moderate traffic: (Red) Heavy traffic: Section affected by serious traffic event: (Purple) Estimated travel time to destination calculated with consideration of traffic information on route.
Black plate (190,1) Traffic information display and scale levels Checking detailed information for traffic information icons on map 2D map and Birdview Map event is displayed. You can scroll the message by using the up/down button of the directional switch or the steering wheel. 4. Push
Black plate (191,1) VIEWING AVAILABLE WEATHER INFORMATION INFO: . . 4. Highlight the preferred setting and push . The indicator for the selected setting illuminates. Available setting items . Use Traffic Info.: Enables all traffic information related functions. . Show Incidents on Map: Displays the traffic incidents (e.g., accident) on the map screen. . Show Traffic Flow on Map: Displays the traffic flow with an arrow on the map screen. .
Black plate (192,1) emergency situations can arise without warning. Relying only on XM NavWeatherTM information could result in serious personal injury. XM NavWeatherTM information is available in limited markets. To subscribe to or check if this service is available in the area, call 1-800-XMRADIO (1-800-967-2346) or access www. xmradio.com/navweather. INFO: . .
Black plate (193,1) tion. . Weather Map: Displays the current weather map for the preferred area. . Temperature Map: Displays the current temperature map for the preferred area. . Warnings Map: Displays the current watches/warnings map for the preferred area. . Road Condition Map: Displays the current road condition map for the preferred area. 1. Push . 2. Highlight [Weather Info] and push . 4. Highlight [Select Other City from Menu] and push .
Black plate (194,1) 1. Highlight [Current Weather and Forecasts] and push . 6. Highlight the preferred city from the list and push . INFO: 3. A weather information screen is displayed. Highlight [Forecast] and push . 2. Highlight the preferred area and push . [Select Other City from Menu] is not available while driving. Current weather and forecasts The current weather information and a three-day forecast for the current location, the destination or the preferred city.
Black plate (195,1) Weather Map Setting by voice command 1. Push < The current weather map can be confirmed for the current location, the destination, the entire country or the preferred city. > located on the steering wheel. 2. After the tone sounds, speak a command. To display the list for weather information: “Weather Information” (Alternate Command Mode) Warnings and watches history A list can be displayed for the warning/watch events detected around the current location.
Black plate (196,1) INFO: [Destination Map] is not available unless a destination is set for the route guidance. INFO: Touch [Legend] to display the map legend. Setting by voice command 1. Push < > located on the steering wheel. 2. After the tone sounds, speak a command. To display the list for weather map: “Weather Map” (Alternate Command Mode) Temperature Map 3. A weather map is displayed. The weather and precipitation level are shown by colors.
Black plate (197,1) perature information is shown by numbers and colors. 4. Push to return to the previous screen. Push
Black plate (198,1) current location map screen. INFO: Touch [Legend] to display the map legend. Road Condition Map The current road condition can be confirmed for the current location, the destination, the entire country or the preferred city. 1. Highlight [Road Condition Map] and push . 2. Highlight the preferred map area and push . INFO: [Destination Map] is not available unless a destination is set for the route guidance. 3. A road condition map is displayed.
Black plate (199,1) Weather information icons Clear Mostly Clear Snow Heavy Snow Dust/Sand Smoke/Ash Partly Cloudy Thunderstorm Mostly Cloudy Tornado/Funnel Cloud AUTOMATICALLY DISPLAY WARNINGS/WATCHES When an urgent warning/watch is detected around the current vehicle location, a message pops up automatically with a voice announcement. Cloudy Haze The message includes the weather icon and text describing the event. Fog INFO: . The pop-up messages and announcements can be set to on or off.
Black plate (200,1) Weather information settings The settings can be confirmed and changed for the urgent weather information related functions. information. . Voice Announcements: Provides urgent information announcements for warnings and watches around the current location.
Black plate (201,1) MAP UPDATE INFO: . . The “Other Watches” category in the “Other” category includes Inland Hurricane Watch, Hurricane Watch, Typhoon Watch, Tropical Storm Watch, Inland Tropical Storm Watch and Fire Weather Watch.
Black plate (202,1) VIEWING NAVIGATION SYSTEM VERSION INFORMATION VIEWING GPS CURRENT LOCATION INFORMATION This displays the map version information. This displays GPS information, such as the positioning status, latitude/longitude, altitude and satellite locations. 2. Highlight [Navigation Version] and push . 3. Push < > to return to the previous screen. Push
Black plate (22,1) 7 Other settings Settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Audio settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Display settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black plate (206,1) SETTINGS SCREEN The navigation system can be customized to make it easier for you to use. . [Bluetooth]: Set Bluetooth® Audio and Phone. “Bluetooth settings” page 3-24 . [Volume & Beeps]: Adjusts the volume and sets the beep function. “VOLUME ADJUSTMENT” page 7-6 . [Display]: Adjusts the display. “DISPLAY SETTINGS” page 7-4 . [Clock]: Changes the clock settings. “CLOCK SETTINGS” page 7-7 . [Others]: BASIC OPERATION 1. Push . 2.
Black plate (207,1) AUDIO SETTINGS This allows to you adjust the speaker tone quality and sound balance. Available items . [Bass]: Adjust the tone quality of the bass by rotating the center dial in the direction of [+] or [−]. . [Treble]: Adjust the tone quality of the treble by rotating the center dial in the direction of [+] or [−]. . [Balance]: Adjust the sound level between the left and right speakers by rotating the center dial in the direction of [Left] or [Right]. .
Black plate (208,1) DISPLAY SETTINGS This menu turns on and off the display, adjust the image quality of the navigation screen and change the color of the menu screen. BASIC OPERATION 1. Push . DISPLAY ADJUSTMENT Available setting items This menu turns on and off the display and adjusts the image quality of the navigation screen. . [Display]: Turn on or off the screen. “Display” page 7-5 . [Brightness]: Adjust the screen brightness. “Brightness” page 7-5 .
Black plate (209,1) Display Brightness Background color To turn off the display, push . The display can also be turned off by pushing OFF> for more than 2 and holding < seconds. Adjust the display brightness by rotating the center dial in the direction of [+] or [−]. Select to toggle between the day screen and night screen. Each time [+] or [−] is pushed, the display brightness changes. Contrast Day screen When any button is pushed with the display off, the display turns on.
Black plate (210,1) VOLUME ADJUSTMENT This turns on and off, as well as adjusts, the phone function (ringer, incoming and outgoing volume), the voice guide function and the beep function. BASIC OPERATION Night screen INFO: 2. Highlight the preferred menu color and push . The background color setting can also be changed using the . SETTING COLOR THEME 1. Push . 2. Highlight [Volume & Beeps] and push . 3. Highlight the preferred adjustment item and push .
Black plate (211,1) CLOCK SETTINGS Available setting items . [Audio Volume]: Adjust the volume level of the audio system by rotating the center dial in the direction of [+] or [−]. . [Guidance Volume]: Adjust the volume level of voice guidance by rotating the center dial in the direction of [+] or [−]. . [Ringtone]: Adjust the volume level of the ringtone by rotating the center dial in the direction of [+] or [−]. .
Black plate (212,1) COMFORT & CONV. SETTINGS Available setting items . . . [On-screen Clock]: Select to toggle the clock display located in the top right corner of the display between on and off. The indicator light illuminates when the clock display is set to on. [Clock Format (24h)]: Select the clock format between 12-hour and 24-hour times. The indicator light illuminates when the clock is set to the 24hour format. [Offset (hour)]: Use the center dial to adjust the offset value (between −12 and +12).
Black plate (213,1) LANGUAGE AND UNIT SETTINGS . . Speed Sensing Wiper Interval: When this item is turned to ON, the wiper interval is adjusted automatically according to the vehicle speed. Selective Door Unlock: When this item is turned to ON, only the driver’s door is unlocked first after the door unlock operation. When the door handle request switch on the driver’s or front passenger’s side door is pushed to be unlocked, only the corresponding door is unlocked first.
Black plate (214,1) UNIT SETTINGS 1. Push . 2. Highlight [Others] and push . 3. Highlight [Language & Units] and push . UNIT SETTINGS (pressure) 5. Highlight the preferred unit and push . The indicator of the selected unit illuminates. Available units — US: mile, MPH, 8F, MPG 1. Push . 2. Highlight [Others] and push . 3. Highlight [Language/Units] and push . — Metric: km, km/h, 8C, L/100 km 6. Push < > to return to the previous screen.
Black plate (215,1) IMAGE VIEWER The image files in the USB memory will be displayed. 5. Highlight the preferred unit and push . The indicator of the selected unit illuminates. Available units — psi 1. Press . 2. Select [Others] and press . 3. Select [Image Viewer] and press . — kPa 6. Push < screen. FULL SCREEN DISPLAY > to return to the previous The full screen display will appear when selecting [Full Screen Display] and press .
Black plate (216,1) display the previous file. SETTING THE IMAGE VIEWER . If the file name is too long, some file names may not be entirely displayed. The Image Viewer setting display will appear when selecting [Settings] on the full screen display and pushing . The following settings are available for the full screen display. . Slideshow Speed Choose [Slideshow Speed] and push . From the following display, select the changing time from 5, 10, 30, 60 seconds or “No Auto Change”. .
Black plate (217,1) MEMO Other settings 7-13 Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (218,1) MEMO 7-14 Other settings Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (25,1) 8 Voice recognition NISSAN voice recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Standard mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Confirming how to use voice commands. . . . . . . . . . . . . . 8-2 Using Voice Recognition System . . . . . . . . . . . . . . . . . . . . . . . 8-4 Before starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black plate (220,1) NISSAN VOICE RECOGNITION STANDARD MODE Speaker Adaptation function available in that mode. “SPEAKER ADAPTATION” page 8-23 Otherwise, it is recommended that Alternate Command Mode be turned OFF and Standard Mode be used for the best recognition performance. NISSAN Voice Recognition allows hands-free operation of the navigation system and other systems equipped on this vehicle, in one of two modes, Standard Mode or Alternate Command Mode.
Black plate (221,1) Available items Getting Started Practicing voice commands . Before using the voice recognition system for the first time, it is possible to confirm how to use commands by viewing the Getting Started section of the User Guide. Practice for using the voice recognition function can be performed by repeating a phone number after the system announces it. [Getting Started]: Describes the basics of how to operate the voice recognition system. .
Black plate (222,1) Tutorials on operation of voice recognition system 1. Highlight [Help on Speaking] and push . When selecting [Using the Address Book], [Finding a Street Address] or [Placing Calls], the system displays tutorials on how to perform these operations using voice recognition. 2. To confirm the page, scroll the screen using the up and down switches of the main directional buttons or the center dial. without pausing between words. GIVING VOICE COMMANDS 1. Push
Black plate (223,1) Operating tips How to speak numbers . Speak a command after the tone. . Commands that are available are always shown on the display and spoken through voice menu prompts. Commands other than those that are displayed are not accepted. Follow the prompts given by the system. NISSAN Voice Recognition requires a certain way to speak numbers when giving voice commands. Refer to the following examples. . If the command is not accepted, the system announces, “Please say again”.
Black plate (224,1) Command List Category Command: Command Action Navigation Operates Navigation function. Phone Operates Phone function. Information Displays vehicle Information function. Audio Operates Audio function. Help Displays User Guide. Navigation Command: Command Action Home Sets a route to the home that is stored in the Address Book. Address Searches for a location by the street address specified, and sets a route (for continental U.S. and Canada only).
Black plate (225,1) Information Command: Command Action Fuel Economy Displays fuel economy information. Maintenance Displays maintenance information. Traffic Information Turns the traffic information system on or off. Where am I? Displays the current location. Vehicle Phone Command: Command Action Dial Number Makes a call to a spoken phone number up to 10 digits. Vehicle Phonebook Makes a call to a contact that is stored in the Vehicle Phonebook.
Black plate (226,1) Audio Command: Command Action AM Turns to the AM band, selecting the station last played. FM Turns to the FM band, selecting the station last played. XM Turns to the XM Satellite band, selecting the channel last played. Music Box Turns on the “Music Box” hard disk drive audio system. CD Starts to play a CD.
Black plate (227,1) VOICE COMMAND EXAMPLES To use the voice recognition function, speaking one command is sometimes sufficient, but at other times it is necessary to speak two or more commands. As examples, some additional basic operations that can be performed by voice commands are described here. Example 1: Setting destination by street address 1. Push < > located on the steering wheel. 4. Speak “Address”. 6. Speak the name of the city, “Gardena”.
Black plate (228,1) INFO: If the house number is unknown, speak “No house number”. 9. Speak the name of the street, “South Figueroa street”. INFO: . Only the official street names stored in the map database can be recognized by the system. To improve accuracy, speak the street name precisely and include Boulevard, Way, North, South, etc., if known. If unsure of the full name, speaking only part of the street name such as “Figueroa” is acceptable, but recognition accuracy may be reduced. .
Black plate (229,1) Example 2: Placing call to phone number 800-662-6200 1. Push < 4. Speak “Dial Number”. > located on the steering wheel. 5. Speak “800”. 7. The system announces, “Please say last four digits or say change number”. Speak “6200”. 2. The system announces, “Would you like to access Phone, Navigation, Information, Audio or Help?”. 3. Speak “Phone”. 6. The system announces, “Please say next three digits or dial, or say change number”. Speak “662”. 8.
Black plate (230,1) prompts. 9. The system makes a call to 800-662-6200. INFO: . Speaking “800-662-6200” (10 continuous digits) or “662-6200” (7 continuous digits) is acceptable, if the area code is not necessary. However the 3-3-4 digit grouping is recommended for improved recognition. “How to speak numbers” page 8-22 . The NISSAN voice recognition system is not limited to recognizing phone numbers of only 7 or 10 digits.
Black plate (231,1) Alternate Command Mode 6. Speak “Dial”. 7. The system makes a call to 011-81-111222-333. INFO: Any digit input format is available in the International Number input process. The following section is applicable when Alternate Command Mode is active. “SETTING ALTERNATE COMMAND MODE” page 8-23 When Alternate Command Mode is active, an expanded list of commands can be used after >. In this mode, available compushing < mands are not fully shown on the display or prompted.
Black plate (232,1) Available items . . [Command List]: A list of voice commands that the system can accept is displayed. [User Guide]: A simplified operation manual of the voice recognition system can be displayed and how to use the voice commands can be confirmed. Example: Displaying the navigation command list: 1. Push . 2. Highlight [Others] and push . 3. Highlight [Voice Recognition] and push . Available items . Phone Commands . Navigation Commands .
Black plate (233,1) Command List Navigation Command: Command Action Home Sets a route to your home location. Address Sets a route to the street address that you specify (for continental U.S. and Canada only). Places Sets a route to a facility near the current vehicle location. Address Book Sets a route to a location stored in the Address Book. Previous Destinations Sets a route to a previously entered destination. Previous Start Point Sets a route to the previous starting point.
Black plate (234,1) INFO: The words in italics are variable. Information Command: Command Action Fuel Economy Displays fuel economy information. Tire Pressure Displays tire pressure information. Maintenance Displays maintenance information. Where am I? Displays the current location. Traffic Information Turns the traffic information system on or off. Weather Information Displays weather information. Weather Map Displays the weather map.
Black plate (235,1) Audio Command: Command Action Music Box Turns on the “Music Box” hard disk drive audio system. CD Starts to play a CD. FM Turns to the FM band, selecting the station last played. AM Turns to the AM band, selecting the station last played. XM Turns to the XM Satellite Radio band, selecting the channel last played. USB Turns on the USB memory. Bluetooth Audio Turns on the Bluetooth audio player. AUX Turns on the AUX.
Black plate (236,1) Help Command: Command Action Navigation Commands Displays the navigation command list. Phone Commands Displays the phone command list. Audio Commands Displays the audio command list. Information Commands Displays the information command list. Help Commands Displays the help command list. User Guide Displays the User Guide Speaker Adaptation The system memorizes the voices of up to three persons for better voice recognition performance.
Black plate (237,1) CONFIRMING HOW TO USE VOICE COMMANDS It is possible to confirm how to use voice commands by accessing a simplified User Guide, which contains basic instructions and tutorials for several voice commands. Available items Getting Started . [Getting Started]: Describes the basics of how to operate the voice recognition system. .
Black plate (238,1) Practicing voice commands Useful tips for correct operation Practice for using the voice recognition function can be performed by repeating a phrase after the system announces it. It is possible to display useful speaking tips that may help the system to accept a voice command correctly. 1. Highlight [Using the Address Book] and push . The tutorial starts. 1. Highlight [Let’s Practice] and push . 1. Highlight [Help on Speaking] and push . 2.
Black plate (239,1) USING VOICE RECOGNITION SYSTEM Initialization 1. Highlight [Voice Recognition Settings] and push . 2. To confirm the page, scroll the screen using the up and down switches of the main directional buttons or the center dial. 1. Highlight [Adapting the System to Your Voice] and push . The tutorial starts. Adapting Voice Recognition System to Your Voice The voice recognition system is equipped with a learning function to adapt to the user’s voice for better recognition.
Black plate (240,1) GIVING VOICE COMMANDS 1. Push < give the command at once. Remember to wait for the tone before speaking. > located on the steering wheel. . To adjust the volume of the system feedback, push the volume control buttons [+] or [−] on the steering wheel or use the audio system volume control knob while the system is making an announcement. How to speak numbers NISSAN Voice Recognition requires a certain way to speak numbers when giving voice commands. Refer to the following examples. 2.
Black plate (241,1) SPEAKER ADAPTATION and the system announcement mode switches to the short mode. 5. Push to return to the previous screen. Push
Black plate (242,1) 5. Highlight the user whose voice is memorized by the system, and push . 7. Highlight the voice command category to be learned by the system, and push . The voice command category list is displayed. 9. The system announces, “Please say a command”. 10. After the tone sounds and the icon on the screen changes from [ ] to [ ], speak a command. 6. Highlight [Start Speaker Adaptation Learning] and push . 8.
Black plate (243,1) INFO: With [Continuous Learning] set to on, the system does not go back to the command list screen, allowing to continue voice command learning by the system. 12. If the system has learned the command correctly, “None” will change to “Stored”. Editing registered items It is possible to edit user names and select learning function settings. 5. Highlight a user to edit, and push . 7. Highlight an item to edit, and push . Setting items 1. Push . 2.
Black plate (244,1) Example 1: Switching map to 2D (Plan View) mode 1. Push < displayed in 2D (Plan View). Example 2: Setting destination using places list 4. If a route is already set, choose “Near Current Location”, “Along Route” or “Near Destination”. 5. After the tone sounds and the icon on the screen changes again, speak “Along Route”. > located on the steering wheel. 2. The system announces, “Please say a command”. 3.
Black plate (245,1) 8. Voice feedback will be provided when the command is accepted, and the list of places of interest in the category specified in the previous step appears. Example 3: Setting destination by street address 9. After the tone sounds and the icon on the screen changes again, speak “One”. 5. Speak the name of the city, “Gardena”. 1. Push < > located on the steering wheel. 2. The system announces, “Please say a command”. 10.
Black plate (246,1) INFO: If the house number is unknown, speak “No house number”. 7. Voice feedback will be provided when the command is accepted, and the list of street names appears. 8. After the tone sounds and the icon on the screen changes again, speak “One”. 10. To confirm the destination location on the map, speak “Show Map”. To calculate a route, speak “Calculate Route”. 9. Speak the house number.
Black plate (247,1) MEMO Voice recognition 8-29 Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (248,1) MEMO 8-30 Voice recognition Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (28,1) 9 Multi function meter About multi function meter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Multi function meter list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black plate (250,1) ABOUT MULTI FUNCTION METER The multi function meter allows you to see the vehicle status and the results of driving operation. SAFETY NOTES For your driving safety please read the following warnings. INFO: . The information displayed on the multi function meter is for reference purposes only. Due to road conditions and temperature, the information displayed by the system may vary from actual driving conditions. . You can select the units that the multi function meter displays.
Black plate (251,1) MULTI FUNCTION METER LIST The following information can be displayed on the multi function meter. Performance and vehicle information Information for improving driving smoothness Braking: WARNING Use the information from the multi function meter strictly as a reference to make your driving more comfortable. The readings are not meant to prevent accidents caused by reckless driving or poor driving conditions (due to weather, road condition, etc.).
Black plate (252,1) BASIC OPERATION Information for fuel economy improvement Trip calculator Stopwatch: Gear position: Information displayed on the multi function meter display will differ depending on your intended use of the display. You can choose to select the meters that best suit your needs. HOW TO VIEW THE FUNCTION METER SCREEN The vehicle’s display is divided into different panels that display vehicle information.
Black plate (253,1) 4 & 5 & Screen information & 1 Large panel: Displays the vehicle information meter display, digital display and gauge display. This feature is only available in the 3-panel display mode. Touch the panel to select another meter to display. “PERFORMANCE AND VEHICLE INFORMATION PANEL” page 9-10 2 & 3 & Screen switching: to Scrolls through the screens. Touch to return to the previous screen. Touch proceed to the next screen.
Black plate (254,1) HOW TO SWITCH SCREENS Selecting screen using touch panel Selecting screen by number: Select the screen that you would like to display. The multi function meter screen you selected will appear. Operate the center dial or the touch panel to select the screens that you would like to display on the multi function meter screen. Selecting screen using center dial Turn the center dial and touch the screen that you would like to display.
Black plate (255,1) CUSTOM VIEW SCREEN Selecting screen by scrolling through screens: This screen allows you to display the performance and vehicle information, as needed, in order for you to use your vehicle under optimum conditions. You can display several vehicle information panels at once. Each panel displays digital gauges in the screen area. SELECTING PANEL Select the panel you would like to display and then place it where you would like it to be displayed.
Black plate (256,1) Select using touch panel 1. Touch the screen number you would like to change. 3. Touch the item you would like to display. The displayed panel will change. 2. Touch the panel you would like to change. The meter selection screen will be displayed.
Black plate (257,1) Panel list INFO: There is a difference between the items that you can select as large or small panels. No.
Black plate (258,1) PERFORMANCE AND VEHICLE INFORMATION PANEL The appearance of each panel varies. The way that large panels and small panels are displayed also differs, even when the same mechanical information is displayed. Engine coolant temperature Displays the temperature of the engine coolant. 2. Select the panel and push . INFO: . When this meter displays in red, reduce the operating speed of the engine (RPMs) and drive at a reduced speed. .
Black plate (259,1) Engine oil temperature Displays the engine oil temperature reading. INFO: . When this meter displays in red, reduce the operating speed of the engine (RPMs) and drive at a reduced speed. . Driving while the engine oil temperature is high may cause engine damage. . When screens other than the FUNCTION screen are displayed, the screen will not change, even if the meter values register red zone readings. Engine oil pressure Displays the engine oil pressure.
Black plate (260,1) Transmission oil temperature Displays the transmission oil temperature. Large panel screen Small panel screen INFO: . When this meter displays in red, reduce the vehicle speed and drive at a reduced speed. . Driving while the transmission oil temperature is high may cause transmission damage. . After first starting the engine, it may take a short period of time for the oil pressure to stabilize. This is not a malfunction. .
Black plate (261,1) INFO: . The oil pressure gauge may momentarily have a high reading, but this is a result of oil pressure suppression and does not indicate a malfunction. . If the meter reads red frequently, have your vehicle inspected at your NISSAN dealer or GT-R certified NISSAN dealer. . When screens other than the FUNCTION screen are displayed, the screen will not change, even if the meter values register red zone readings. Boost Speed Displays engine charging pressure.
Black plate (262,1) Fuel/Range Fuel flow Recent fuel economy Display the amount of fuel remaining and the estimated cruising range. Displays the amount of fuel injected into the engine by the fuel injector. In the large panel, this meter displays the timeline of fuel consumption for each minute over the past twenty minutes. In the small panel, this meter displays fuel consumption readings over the past twenty seconds.
Black plate (263,1) INFO: . . The small panel will display “-.-”: — when the vehicle is stopped — for the first few moments of driving The large panel will not display a graph while the vehicle is stopped. Torque split Accel pedal Displays the amount of forward distributed torque. This can only be displayed as a small panel. Displays the accelerator pedal position. This can only be displayed as a small panel.
Black plate (264,1) Brake pedal Steering Cornering G Displays the brake pedal position. This can only be displayed as a small panel. Displays the steering angle. This can only be displayed as a small panel. Displays the lateral g-force exerted on the vehicle. In the large panel, this meter displays readings for the past 20 seconds. In the small panel, this meter displays the lateral g-force being exerted on the vehicle at the time of the reading.
Black plate (265,1) INFO: Large panel screen . Due to the slope of a road, this meter may register g-force even when the vehicle is stopped. This is not a malfunction. . When the VDC or the ABS is activated, a mark will appear on the far left side of the panel (large panel only). . The scale of the readout is adjusted automatically to accommodate readings that exceed the upper limit of the meter. Accel/Braking G Displays the fore/aft g-force exerted on the vehicle.
Black plate (266,1) INFO: Large panel screen . Due to the slope of a road, this meter may register g-force even when the vehicle is stopped. This is not a malfunction. . When the VDC or the ABS is activated, a mark will appear on the far left side of the panel (large panel only). . The scale of the readout is adjusted automatically to accommodate readings that exceed the upper limit of the meter. Total g-force Displays the total combined g-force exerted on the vehicle.
Black plate (267,1) INFO: Large panel screen . Due to the slope of a road, this meter may register g-force even when the vehicle is stopped. This is not a malfunction. . When the VDC or the ABS is activated, a mark will appear on the far left side of the panel (large panel only). . The scale of the readout is adjusted automatically to accommodate readings that exceed the upper limit of the meter. Clock Displays the current time. This can only be displayed as a small panel.
Black plate (268,1) DRIVING SUPPORT SCREEN 4 & ACCELERATION SCREEN The acceleration screen displays the results of how the vehicle behaves based on the manner in which you operate the vehicle. The information displayed is for confirmation purposes. The results of how you use the accelerator pedal can be displayed as an acceleration g-force timeline. You can use this information to improve your operation of the accelerator pedal. 5 & .
Black plate (269,1) Using result screens to improve driving Timeline and driving that show smooth operation of accelerator pedal: Displaying timeline of quick and sudden acceleration and driving: 1 & 1 & This section explains how to use the driving timeline screens. Use this information to make your driving smoother. INFO: The criteria for smooth driving may vary depending on road conditions. Use this information for reference purposes only.
Black plate (270,1) BRAKING SCREEN 4 & The braking screen displays the results of how the vehicle behaves based on the manner in which the driver operates the vehicle. The information displayed is for confirmation purposes. The results of how the brake pedal is used are displayed as a timeline of g-force exerted on the vehicle during deceleration. Use the information to improve your operation of the brake pedal. 5 & .
Black plate (271,1) Using result screens to improve driving Timeline and driving that show smooth operation of brake pedal: Timeline and driving that show sudden operation of brake pedal: 1 & 1 & This section explains how to use the driving timeline screens. Use this information to make your driving smoother. INFO: The criteria for smooth driving may vary depending on road conditions. Use this information for reference purposes only.
Black plate (272,1) STEERING SCREEN 3 & The steering screen allows you to confirm how the vehicle responds to your driving by displaying the results of how you operate the vehicle. The results of your driving are displayed as a timeline of the g-force exerted on the vehicle. Use the displayed information to improve your steering smoothness. 4 & 5 & G-meter: Displays the g-force currently being exerted on the vehicle due to deceleration. SPEED: Displays the current driving speed.
Black plate (273,1) Using result screens to improve driving Timeline and driving that show smooth handling when driving through S-curve: Timeline and driving that show sudden turning of steering wheel: 1 & 1 & This section explains how to use the driving timeline screens. Use this information to make your driving smoother. INFO: The criteria for smooth driving may vary depending on road conditions. Use this information for reference purposes only.
Black plate (274,1) GEAR POSITION SCREEN The GEAR POSITION screen displays the gear you are currently in, the current speed, and the fuel economy level for each gear. This allows you to verify the best gear to use at your current driving speed. Use this panel to improve your operation of the shift lever or paddle shifters. 2 & 3 & 4 & 5 & Speedometer (vertical): Displays the current speed. This scale changes with the speed of the vehicle.
Black plate (275,1) Changing gears for engine braking or power: FUEL ECONOMY SCREEN The FUEL ECONOMY screen allows you to verify the fuel efficiency of your driving. Use this information to make your driving more fuel efficient. 2 & RECENT FUEL ECON. (fuel economy over a given section): Displays the fuel economy for the past 20 seconds while the vehicle is being driven. 3 FUEL EFFICIENCY (fuel economy level (real & time)): Displays the current fuel economy level (measured on a scale of 10).
Black plate (276,1) DRIVING RECORD SCREEN Timeline and driving of good fuel economy: Timeline and driving of poor fuel economy: This allows you to measure/display the timeline and waypoint history over a given time. STOPWATCH SCREEN With the STOP WATCH screen you can measure a segment of time or passing time. You can also display and save recorded timelines and data. 1 & 2 & The average fuel economy level is high, indicating fuel-efficient driving.
Black plate (277,1) 3 & 4 & SPEED: Displays the vehicle speed while driving. ELAPSED TIME: Displays the total elapsed time measured since the stopwatch function was started. Measuring timed distance To measure the timed distance, use or on the steering switch. 1. With the STOP WATCH screen displayed, push . The timer-on indicator will flash when the stopwatch function is active. 2.
Black plate (278,1) Checking timed distance list Saving to USB memory You can review the list of past measured times. You can save the time records saved in the system onto a USB memory. 3. Select [Stop Watch Times]. The details of the selected record will be displayed. 1. Select [TIME LOG]. The list screen will be displayed. INFO: You can use either the center dial or the touch panel to scroll through the list. 1. Insert the USB memory in the media slot. 2.
Black plate (279,1) NOTICE Inserting objects other than a USB memory into the USB connector can cause damage. Do not insert anything other than a USB memory into the USB connector. 3. Select the record you would like to display. The menu screen will be displayed. Deleting records Use the following procedure to delete time records saved in the system. INFO: . Time records are saved to the USB memory in the CSV format. .
Black plate (280,1) DRIVER’S NOTES SCREEN You can record the waypoints that you pass using the DRIVER’S NOTES screen. 4 & TRIP DISTANCE: Displays the driving time measured starting from when the Driver’s notes function was activated. NOTICE Even when the cruising distance displays that the vehicle has a sufficient amount of fuel to travel a given distance, when the fuel indicator approaches E (empty) , or the fuel warning light illuminates, be sure to fuel your vehicle. 3.
Black plate (281,1) Timing waypoints To measure a waypoint, use or on the steering switch. 2. Pass the waypoint. The waypoint will be automatically recorded and will be displayed in the list. 1. With the DRIVER’S NOTES screen displayed, push . The DRIVER’S NOTES function will activate, and the timer indicator will flash. 4. Push . The DRIVER’S NOTES function will end. The waypoint will be displayed as described below: .
Black plate (282,1) INFO: . . The STOP WATCH function can only be used when the clock is activated. When the STOP WATCH function is activated, you cannot use the waypoint timer. This is the waypoint timer after use of the STOP WATCH function is completed. . Even if you stop the engine, when RESUME is set to ON, the timer will not reset and you will be able to continue timing your travel. .
Black plate (283,1) The menu screen will be displayed. Deleting records This allows you to delete waypoint records that are saved in the system. 3. Select [Delete Driver’s Notes]. The message screen will be displayed. 3. Select [Driver’s Notes]. The details of the selected record will be displayed. INFO: 1. Select [MARK LIST]. The list screen will be displayed. You can use either the center dial or the touch panel to scroll through the list. 4. Select [YES]. The time record will be deleted. 2.
Black plate (284,1) MEMO 9-36 Multi function meter Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (31,1) 10 General system information Current vehicle location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Display of current vehicle location . . . . . . . . . . . . . . . . . . . . What is GPS (Global Positioning System)?. . . . . . . . Incorrect display of vehicle position . . . . . . . . . . . . . . . . . . Detailed Map Coverage Areas (MCA) for navigation system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black plate (286,1) CURRENT VEHICLE LOCATION DISPLAY OF CURRENT VEHICLE LOCATION This navigation system combines the data obtained from the vehicle (by gyro sensor) and from GPS (Global Positioning System) satellites to calculate the current location of the vehicle. This position is then displayed throughout route guidance to a destination. WHAT IS GPS (Global Positioning System)? GPS is a position detecting system that uses satellites deployed by the U.S. government.
Black plate (287,1) NOTICE Route guidance provided by the navigation system does not take carpool lane driving into consideration, especially when carpool lanes are separated from other road lanes. INCORRECT DISPLAY OF VEHICLE POSITION * In a canyon The following cases may affect the display accuracy of the vehicle’s position or traveling direction. The accuracy will return to normal if the driving conditions return to normal. * When the vehicle is traveling in an area with a grid pattern road system.
Black plate (288,1) * When the vehicle is traveling on a continuous, slowly curving road. * When the vehicle is traveling on a road with repeating S-shaped curves. * When the vehicle is on a loop bridge. * When the vehicle is on a snow-covered or unpaved road. * When repeatedly turning left or right, or driving in zigzags. * When the vehicle is rotated on a parking lot turntable while the ignition switch is off.
Black plate (289,1) INFO: * When driving on a road not displayed on the map screen or a road that has been changed due to additional construction or other reasons. Canada. . The vehicle icon may be misaligned when starting the vehicle just after starting the engine. Map data includes two types of areas: “Detailed coverage areas” providing all detailed road data and other areas showing “Main roads only”. . The vehicle icon may also be misaligned if different sized tires or tire chains are installed.
Black plate (290,1) ROUTE CALCULATION . There may be cases that carpool lanes are included on a suggested route when the automatic rerouting function is activated, even if the “Use Time Restricted Roads” is turned off. “Setting conditions for route calculation” page 2-65 . The navigation system does not provide route guidance for roads displayed in dark green. .
Black plate (291,1) ROUTE GUIDANCE . — If a part of the route is included in the “Avoid Area”. The following may occur when the route is displayed. — If you calculate a route on a main road, the starting point of the route may not exactly match the current vehicle location. — The endpoint of the route may not exactly match the destination. — If you calculate a route on a main road, the system may display a route from another main road. This may be because the position of the vehicle icon is not accurate.
Black plate (292,1) . Route guidance provided by the navigation system does not take carpool lane driving into consideration, especially when carpool lanes are separated from other road lanes. 1. “In about one quarter mile (400 meters), right (left) turn.” Notification of freeway entrance 2. “Right (left) turn ahead.” Notification of consecutive intersections on ordinary roads DIRECTIONS PROVIDED AND DISTANCES TO GUIDE POINTS Directions will differ, depending on the road type.
Black plate (293,1) Notification of freeway junction Notification of freeway exit 1. “In about one mile (1.6 kilometers), exit on your right.” 2. “Take the second exit on your right.” 1. “In about one mile (1.6 kilometers), keep to the right (left) onto (road number and direction), then in about one quarter mile (400 meters) keep to the right (left).” 2.
Black plate (294,1) approaching the endpoint of the suggested road, voice guidance will announce, “Entering the road with incomplete map data. Please use the direction arrow and distance information to proceed to your destination.” REPEATING VOICE GUIDANCE This function is available throughout route guidance, from the time after the route calculation is completed until the vehicle arrives at the destination. Push . Voice guidance will be repeated. .
Black plate (295,1) NOTES ON XM NavTraffic® INFORMATION . . Because it is not possible to consider data concerning roads that are seasonally available or unavailable, a route may be displayed that does not match the actual traffic restrictions. Be sure to follow the actual traffic restrictions while driving. Canada and Alaska contain many roads with incomplete map data. As a result, when searching for a route, the route may include roads with incomplete data.
Black plate (296,1) NOTES ON XM NavWeatherTM INFORMATION information sources. . The XM NavWeatherTM information service is not provided for some cities. In addition, the cities for which the weather information service is provided may be changed. . In some cases, infrastructure problems may prevent the complete display of the weather information. This is not a malfunction. .
Black plate (297,1) MAP DATA HOW TO ORDER MAP DATA UPDATES To order updated map data, contact the NISSAN NAVIGATION SYSTEM HELPDESK. See the contact information on the inside front cover of this manual. ABOUT MAP DATA 1. This map data has been prepared by HITACHI, LTD. under licence from ZENRIN CO., LTD. and NAVTEQ. ZENRIN CO., LTD. has added, processed and digitized data based on the digital road map data of Navigation Technologies Corporation.
Black plate (298,1) ber that actual road conditions and traffic regulations take precedence over the information contained on the navigation system. — The Software may contain inaccurate or incomplete information due to the passage of time, changing circumstances, and the sources of information used. Please respect current traffic conditions and regulations at all times while driving.
Black plate (299,1) systems, or applications installed or otherwise connected to or in communication with vehicles, capable of vehicle navigation, positioning, dispatch, real time route guidance, fleet management or similar applications; or (b) with or in communication with any positioning devices or any mobile or wireless-connected electronic or computer devices, including without limitation cellular phones, palmtop and handheld computers, pagers, and personal digital assistants or PDAs. Warning.
Black plate (300,1) HOW TO HANDLE DISPLAY NAVTEQ Data (hereinafter “Data”) is a “commercial item” as that term is defined at 48 C.F.R. (“FAR”) 2.101, is licensed in accordance with ENDUSER TERMS, and each copy of the Data delivered or otherwise furnished shall be marked and embedded as appropriate with the following “Notice of Use,” and shall be treated in accordance with such Notice: The display is a liquid crystal display and should be handled with care. WARNING Never disassemble the display.
Black plate (301,1) MEMO General system information 10-17 Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (302,1) MEMO 10-18 General system information Model "R35-N" EDITED: 2009/ 10/ 30
Black plate (34,1) 11 Troubleshooting guide Customer assistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Basic operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vehicle icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black plate (304,1) CUSTOMER ASSISTANCE For assistance or inquiries about the NISSAN Navigation System, or to order updated map data, contact the NISSAN NAVIGATION SYSTEM HELPDESK. See the contact information on the inside front cover of this manual.
Black plate (305,1) NAVIGATION BASIC OPERATIONS Symptom No image is displayed. No voice guidance is available. or The volume is too high or too low. Possible cause The brightness is at the lowest setting. Possible solution Adjust the brightness of the display. The system in the video mode. Push on the control panel to change the mode. “Audio system” page 3-1 The display is turned off. Push < The volume is not set correctly, or it is turned off. Adjust the volume of voice guidance.
Black plate (306,1) VEHICLE ICON Symptom Possible cause Possible solution Names of roads and locations differ between Plan View and BirdviewTM. This is because the quantity of the displayed information is reduced so that This is not a malfunction. the screen does not become too crowded. There is also a chance that names of the roads or locations may be displayed multiple times, and the names appearing on the screen may be different because of a processing procedure.
Black plate (307,1) Symptom The location of the vehicle icon is misaligned from the actual position. Possible cause Possible solution When using tire chains or replacing the tires, speed calculations based on Drive the vehicle for a while (at approximately 19 the speed sensor may be incorrect. MPH for about 30 minutes) to automatically correct the vehicle icon position. If this does not correct the vehicle icon position, contact your NISSAN dealer or GT-R certified NISSAN dealer.
Black plate (308,1) ROUTE CALCULATION AND VISUAL GUIDANCE Symptom Possible cause Possible solution Waypoints are not included in the auto reroute calculation. Waypoints that have been already passed are not included in the auto To go to that waypoint again, edit the route. reroute calculation. Route information is not displayed. Route calculation has not yet been performed. Set the destination and perform route calculation. The vehicle is not on the suggested route. Drive on the suggested route.
Black plate (309,1) Symptom Possible cause Possible solution The part of the route that the vehicle has A route is managed by sections between waypoints. If the vehicle This is not a malfunction. already passed is deleted. passed the first waypoint, the section between the starting point and the waypoint is deleted (it may not be deleted depending on the area). An indirect route is suggested. The landmark information does not correspond to the actual information.
Black plate (310,1) VOICE GUIDANCE Symptom Voice guidance is not available. Possible cause Voice guidance is only available at certain intersections marked with In some cases, voice guidance is not available even when the vehicle should make a turn. Possible solution . This is not a malfunction. The vehicle has deviated from the suggested route. Go back to the suggested route or request route calculation again. Voice guidance is set to off. Turn on voice guidance. Route guidance is set to off.
Black plate (311,1) TRAFFIC INFORMATION Symptom The traffic information is not displayed. Possible cause Possible solution The traffic information is not set to on. Set the traffic information to on. The vehicle is in an area where traffic information is not available. Scroll to an area where traffic information is available. The subscription to XM NavTraffic® is incomplete, or the subscription to XM NavTraffic® has expired. Check the subscription status of XM NavTraffic®.
Black plate (312,1) AUDIO SYSTEM Symptom Cause and Countermeasure Check if the disc or USB device was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player, and if there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the player will play correctly after it returns to the normal temperature.
Black plate (313,1) BLUETOOTH® HANDS-FREE PHONE SYSTEM The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved. Symptom Solution 1. Ensure that the command is valid. “Voice recognition” page 8-1 2. Ensure that the command is spoken after the tone. System fails to interpret the command correctly. 3.
Black plate (314,1) VOICE RECOGNITION Symptom The system does not accept the voice command. or The system accepts the voice command incorrectly. Possible cause Possible solution The interior of the vehicle is too noisy. Close the windows or have other occupants be quiet. The volume of the voice is too low. Speak louder. The volume of the voice is too loud. Speak softer. Pronunciation is unclear. Speak clearly. The voice command is given before the voice recognition system is ready.
Black plate (1,1) 12 Index A C About map data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13 About multi function meter . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 About route guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47 Acceleration screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20 Address book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Air flow control . . . . . . . . . .
Black plate (2,1) Full screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11 G Gear position screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26 Giving voice commands . . . . . . . . . . . . . . . . . . . . . . 8-4, 8-22 H Heating (A/C OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 How to handle display. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-16 How to input letters and numbers. . . . . . . . . . . . . . . .
Black plate (3,1) Setting the image viewer . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12 Settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Speaker adaptation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23 Speed limit indication on map . . . . . . . . . . . . . . . . . . . . 2-94 Standard mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Start-up screen . . . . . . . . . . . . . . . . . . . . .
