TM HD View Finder 多機能HDビューファインダー HDF-700 HDF-700SK HDF-700/S Operating Instructions Before operating the system, please read this manual thoroughly and remain it for future reference. 取扱説明書 Volume1, 1st edition Ver.1.
WARNING For the customers in the U.S.A. To reduce the risk of fire or electric shock,do not expose this apparatus to rain or moisture. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of contents 目次 HD View Finder HDF-700 HDF-700 目次 Names and Functions of Parts 4 各部名称と働き Front panel 4 Rear panel 10 Left side, Right side,Upper and Bottom 13 前面パネル 背面パネル 左側面,右側面,上面,下面, Fixing 14 Connection 20 Adjustments and Settings 26 Outside View and Dimensions 38 Specifications 39 Accessories 40 組み立て方法 接続方法 調整および設定 外形寸法図 仕様 付属品 03
Names and Functions of Parts HD View Finder HDF-700 HDF-700 各部名称と働き Front panel フロントパネル RETURN MAIN Screen (with Bezel and Protector) The display screen is 7.0 inches LCD with the bezel( open size : 152.4mm 91.4mm）. And the screen is covered with the protector(181.4mm 100.6mm). スクリーンは 7インチ液晶で、画面寸法は 152.4mm 92.4mm です。 プロテクターで保護されています。 Front TALLY Indicator LED (RED and GREEN) Lights up to RED or GREEN when the tally signal is input to the TALLY IN 1 connector.
HD View Finder HDF-700 Names and Functions of Parts Front panel フロントパネル POWER Indicator Lights up when the POWER switch is turned on and the power is supplied to the DC IN connector. POWER スイッチが ON のとき点灯します。 VOLUME / PUSH SELECT switch By rotating the switch adjust the audio volume level of the monitor speaker (when the headphone is disconnected) or the headphone level connected to the jack( ).
HD View Finder HDF-700 Names and Functions of Parts Front panel フロントパネル RGB switch Selects the image (Blue only, GREEN only, RED only, full color) in sequence. → Blue only ↓ GREEN only ↓ RED only ↓ full color( LED off ) ↓ ブルーオンリー→グリーンオンリー→レッドオンリー→フルカラー→ の順に切り替えます。 MONO switch Selects the image, monochrome( LED on ) or color. 画面表示のカラー, モノクロ の切替えをします。 UTIL select switch Selects the utility function in sequence as follows.
HD View Finder HDF-700 Names and Functions of Parts Front panel フロントパネル (2) Rotating knob confirms a value. LED LED LED (1) Pressing knob selects USER setting and LED lights on. BRIGHT level control volume and select switch / LED Indicator Pressing the knob selects the USER setting or STANDARD(default) setting. When USER setting is selected( LED indicator lights on ), rotating this knob adjusts the brightness.
HD View Finder HDF-700 Operating the Menus Names and Functions of Parts メニューの操作 Menu Display メニューの表示 Press the MENU button. The menu list is displayed on the screen. Press Menu list INFO PICTURE MARKER AUDIO WAVE FORM VECTORSCOPE ZEBRA Menu Setting メニューの設定 SDI STATUS SETUP Menu Selection and fixing By rotating the ENTER knob button move the cursor to the desired item position and then the submenu list is displayed. Press the knob to fix the selected item and the cursor moves to the submenu list.
HD View Finder HDF-700 MENU list Names and Functions of Parts メニュー項目 ＜Submenu &［factory setting］ ＞ 設定項目 ＜MENU＞ メニュー RETURN SATURATION SHARPNESS PEAKING PICTURE ピクチャー ［50］ ［50］ ［WHITE］ RETURN CENTER ［ON］ ASPECT ［OFF］ SAFTY ［ 95% ］ USER MARKER ［OFF］ WIDTH HEIGHT HORIZONTAL MOVE VERTICAL MOVE CROSS HATCH ［OFF］ MARKER MAT ［CLEAR］ LINE THICKNESS ［1］ LINE TYPE ［WHITE］ MARKER マーカー AUDIO ［ON］ RETURN LEVEL METER ［ON］ METER BACKGROUND［ON］ DISPLAY CHANNELS ［8］ ACTIVE CH ONLY ［ALL］ METER COLUMNS ［DUAL］ DISP
HD View Finder HDF-700 Names and Functions of Parts Rear panel リアパネル Rear TALLY Indicator (RED only) Lights up to RED when the tally signal is input to the TALLY IN 1 or TALLY IN 2. The brightness is exchangeable to OFF/L(low)/H(high) by the TALLY OFF/L/H display select switch. リアタリー(レッドのみ) は、TALLY IN 1 またはTALLY IN 2 のタリー信号で点灯します。 リアタリー（レッドのみ) は、切替スイッチで OFF(消灯)/L(low減光)/H(high)に切り替えることができます。 TC TALLY: The front TALLY indicator can be used as the TC TALLY indicator by the MENU setting.
HD View Finder HDF-700 Names and Functions of Parts Rear panel リアパネル TALLY OFF/L/H display select switch The brightness of the rear tally indicator(RED only) can be selected as follows. H : The tally indicator lights up brightly. L : The tally indicator is dimmed to the lower brightness. OFF : The tally lamp is prevented from lighting. リアタリー(レッドのみ)を (OFF(消灯)/L(low:減光)/H(high)) に切替えます。 SDI(HD/SD) IN 1 connector (BNC) Input the HD-SDI or SD-SDI signal from a camera, etc.
HD View Finder HDF-700 Names and Functions of Parts Rear panel リアパネル AUDIO OUT 1/2 (XLR 3-pin 2) Outputs the de-embedded analog audio signals from the HD/SD-SDI input signal to the SDI IN I connector. The output audio channel from CH 1 to CH 8 can be selected by the AUDIO menu setting. (See Audio signal output select, page 35) The output audio signal can be monitored with the monitor speaker or a headphone.
HD View Finder HDF-700 Names and Functions of Parts Left side, Right side, Upper & Bottom 左側面. 右側面 および 上面, 底面 Left side Right side Bottom Upper Headphone jack (φ 6.3 stereo jack) Connect a headphone to monitor the audio signal selected by pressing the VOLUME/PUSH SELECT switch. ヘッドホンを接続してオーディオ出力をモニターします。VOLUME/PUSH SELECT (ボリューム/切替)スイッチを押して選択した 音声信号をモニターします。 Screw holes ( 2-w1/4, left, right) Used to fix the supplied tilt arm stay.
Fixing 組み立て方法 HD View Finder HDF-700 Fixing VF Tilt Arm Stay Fixing アームの取り付け方法 Make sure to disconnect the connectors before fixing up. 組み立ては、必ず入出力コネクタの配線をはずしてから行ってください。 1 Prepare the supplied VF Tilt Arm Stay, five arm stay screws and washers (one is used to fix up to a camera), and two combination washers, .
HD View Finder HDF-700 Fixing VF Tilt Arm Stay Fixing 3 アームの取り付け方法 Insert the VF Arm Stay into the gap between the combination washer and the screw, and tighten the arm stay screw with the rubber washer.
HD View Finder HDF-700(for HDF-700/S only) Fixing Mounting on Swing Arm (HDF-700/Sのみ)スイングアームへの取り付け方法 Make sure to disconnect the connectors before fixing up. 組み立ては、必ず入出力コネクタの配線をはずしてから行ってください。 1 Prepare a tripod and remove the tripod base and the camera plate. Tripod Base Screws(supplied) 三脚ベースネジ 三脚を用意し、三脚ベース、カメラプレートを外します。 or Tripod Base 三脚ベース Swing Arm (supplied) スイングアーム part for mountig HDF-700 HDF-700取付部 2 Camera Plate カメラプレート Fix up the tripod base and the camera plate to the Swing Arm.
HD View Finder HDF-700(for HDF-700/S only) Mounting on Swing Arm 3 Fixing (HDF-700/Sのみ)スイングアームへの取り付け方法 Fix up the Arm on the tripod and mount HDF-700 on it. アームを三脚に固定し、HDF-700をマウントします。 VF arm stay NOTE : Make sure to mount HDF-700 folding the Swing Arm as shown in Fig. 注意 : HDF-700をマウントする場合は、図のように、 必ずスイングアームを折りたたんだ状態で 行ってください。 3-1 w 1/4 arm stay screw In case of using arm stay fix with w 1/4 arm stay screw.
HD View Finder HDF-700 Fixing Location Stand Removal and Fixing 1 ロケーションスタンドの脱着方法 Loosen/tighten four screws on the bottom to remove/fix.
HD View Finder HDF-700(for HDF-700/S only) Hood Mounting 1 (HDF-700/Sのみ)フードの取り付け方法 Prepare the supplied Hood and four screws. フードと固定ネジ4本を用意します。 2 Fixing Tighten four screws on the left and right side.
HD View Finder HDF-700SK HDF-700 各部名称と働き Studio Kit SK-700 (Hood and Mount Kit for HDF-700SK) HDF-700SK フード および マウントキット Hood Hood Fixing Screw フード固定ネジ Mount Kit Vertical Positioning Screw Knob Horizontal Positioning Screw Knob 垂直方向角度調節ネジ 水平方向角度調節ネジ Removal and Fixing of the hood 1 (Removal) Loosen four screws on the side to remove. フード側面の4本のネジをゆるめて外します。 2 (Fixing) Install the hood and tighten four screws to fix.
Connection 接続方法 HD View Finder HDF-700 HDF-700 接続方法 Power Supply Connection 電源の接続方法 Make sure to turn off the POWER switch of each unit before connecting. 接続する前には、必ず各機器の電源スイッチをOFFにしてください。 1 Connect the supplied AC adaptor to the DC IN connector( XLR 4-pin) on the rear panel. リアパネルのDC IN コネクタにACアダプタを接続します。 DC IN(12V) connector POWER switch XLR 4-pin AC Adaptor (supplied) 2 When the power is supplied from a camcorder, connect the DC output from the camera with the supplied Power tap cable.
HD View Finder HDF-700 Connection HD/SD-SDI video signal connection 1 HD/SD-SDIビデオ信号の接続 Connect the HD/SD-SDI output signal from a camera to the SDI (HD/SD) IN 1 connector. Connect the SDI (HD/SD) 1 OUT connector to the HD/SD-SDI input connector of a switcher, etc. Connect the HD/SD-SDI return video signal from a switcher, etc. to the RET IN connector.
HD View Finder HDF-700 Connection HD/SD Analog Component Video Signal Connection 1 HD/SDコンポーネントアナログ信号の接続 Connect the HD/SD analog component video output signal from a camera to the ANALOG Y/ PB/ PR connectors with BNC cables.
HD View Finder HDF-700 Connection Embedded Audio Signal Output Connection 1 エンベデッドオーディオ信号出力の接続 To output the embedded audio signal connect the HD-SDI signal from a camera, etc. to the SDI(HD/SD) connector of the HDF-700 with a BNC cable and connect the AUDIO OUT 1/2 connectors ( XLR 3-pin ) to a mixer, etc. with XLR 3-pin cables. AUDIO IOUT 1/2 コネクタ からミキサー等へキャノン3ピンケーブルで接続します。 SDI(HD/SD) IN 1 AUDIO OUT 1 AUDIO OUT 2 XLR 3-pin audio signal to Mixer, etc.
HD View Finder HDF-700 Connection TALLY Signal Connection 1 タリー信号の接続 Connect the tally output signal from a camera, a camera adaptor, switcher, etc. to the TALLY 1 connector or TALLY 2 connector. TALLY 1 コネクタまたはTALLY 1 コネクタにカメラ等のタリー出力を接続します。 Front TALLY Rear TALLY Front TALLY Rear TALLY from camera, camera adaptor, switcher, etc. TALLY 1 TALLY 2 Display select switch OFF/L(low)/H(high) 2 The Front TALLY indicator lights up when the tally input signals are as follows.
HD View Finder HDF-700 Connection Zoom Remote Controller (RETURN Controller) Connection ズームリモコンの接続 Using a zoom remote controller, the switching the input signal, from the HD/SD-SDI signal to the RETURN signal, is enabled by pressing the RET(return) button , beside the zooming of the lens and the recording start/stop of the VTR.
Adjustments and Settings 調整および設定 HD View Finder HDF-700 HDF-700 調整・設定 Video Signal Setting and Adjustment ビデオ信号の設定・調整 USER preset functions, etc. work when the video signal is input. 注意 : 各機能は、信号が入力されているとき動作、操作ができます。 信号が入力されているとき操作,設定されていた機能は、信号が遮断されると操作できなくなります。 1 Input signal Select Select a input signal connected to the input connector by pressing INPUT select switch in sequence. And the selected signal and the video format are displayed on the screen.
HD View Finder HDF-700 Adjustments and Settings Video Signal Setting and Adjustment ビデオ信号の設定・調整 3 BRIGHT(brightness)/CONTRAST/PEAKING Adjustment 明るさ/コントラスト/ピーキングの調整 (1)By pressing each knob select the USER preset memory. Then the indicator LED lights on. (2)By rotating the knob adjust each setting. The each setting ranges from 0 to 100. When the LED does not light on, each setting is set to STANDARD(default setting value).
HD View Finder HDF-700 Adjustments and Settings Video Signal Setting and Adjustment ビデオ信号の設定・調整 メニューの操作 - ユーザー設定 の方法 5 Menu Operation - USER Setting By pressing the MENU button, and by rotating and pressing the ENTER knob set the functions. MENUボタン、ENTERツマミで各ファンクションを設定します。 5-1 Menu Display Press the MENU button,and the menu list is displayed on the screen.
HD View Finder HDF-700 Adjustments and Settings User Function Setting 6 User Function/Utility Setting ユーザー設定 ユーザーファンクション/ユーテティリティー(測定器機能)の設定 On the MENU, adjust and set the USER setting of the each function. By pressing the function button on the front panel selecting the USER mode, the set items function. 6-1 Zebra ゼブラ Menu for ZEBRA［default setting］ ZEBRA ［OFF］ ZEBRA button ←← OFF ON RETURN ZEBRA ［OFF］ MODE ［LUMA&CHROMA］ DISP TYPE ［ZEBRA］ Y UPPER LIMIT ［95.0%］ Y LOWER LIMIT ［0.
HD View Finder HDF-700 Adjustments and Settings User Function Setting 6-3 UTILITY ユーザー設定 WAVEFORM ユーティリティー(測定器機能) On the MENU, adjust and set the USER setting of the AUDIO, WAVEFORM and VECTORSCOPE in the USER position of the UTIL function.
AUDIO LEVEL METER -6 16 : 9 VECTORSCOPE HISTOGRAM WAVEFORM 0 -12 -18 -24 -36 -30 -42 -48 -54 -60 ¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦ ¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦ ¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦ ¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦ ← Multi View WAVEFORM+ VECTORSCOPE+ AUDIO 4CH(12CH)+ AUDIO PEAK LOG+ HISTOGRAM -42 -48 -60 -54 ¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦
HD View Finder HDF-700 Adjustments and Settings User Function Setting ユーザー設定 UTILITY - USER Setting USER Setting UTILITY(測定器機能)のユーザー設定 ユーザー設定 ［default setting］ デフォルト設定値 Any item can be set to ON or OFF.
HD View Finder HDF-700 Adjustments and Settings User Function Setting 6-3-2 ユーザー設定 Menu of the WAVEFORM for the UTILITY settings ウェーブフォーム/ ヒストグラムの設定 ON SMALL MEDIUM LARGE LEFT TOP LEFT BOT RIGHT TOP RIGHT BOT OVERLAY 95.0 0.0 OFF RETURN WAVEFORM ［ON］ SIZE ［MEDIUM］ POSITION ［RIGHT BOT］ DISP TYPE ［OVERLAY］ Y OVER LIMIT ［95.0%］ Y UNDER LIMIT ［0.0%］ HISTOGRAM ［OFF］ WAVEFORM/HSG ［ON］ ON or OFF or OVERLAP -7.3 to 109.1 ON or OFF Select the WAVEFORM display, ON or OFF.
HD View Finder HDF-700 Adjustments and Settings AUDIO Signal Setting オーディオの設定・調整 1 AUDIO Function Setting By pressing MENU button on the front panel, access to the MENU displayed on the screen. Access to AUDIO in the MENU and set each setting item.
HD View Finder HDF-700 Adjustments and Settings Audio Signal Setting 音声信号の設定 3 Monitor Audio Selection and Volume Level Adjustment By pressing the VOLUME / PUSH SELECT knob-button select the monitor audio signal by the monitor speaker or the headphone connected to the jack. The audio volume level of the monitor speaker and the headphone is adjusted by rotating the VOLUME/PUSH SELECT knob or by the MENU setting, VOLUME ［from 0 to 40］.
HD View Finder HDF-700 Adjustments and Settings TALLY Signal Setting 1 タリー信号の設定 Make sure that the front and rear TALLY indicators, RED and GREEN, light up properly when the tally signal is input. And make sure that the TALLY OFF/L/H display select switch functions. The brightness of the L position can be selected on the MENU/SAETUP/LOW TALLY BRIGHT, 1 to 8.
HD Monitor HDF-700 Adjustments and Settings Addition 補足 INFO ［1080 i/60］ PICTURE MARKER AUDIO ［ON］ WAVEFORM ［ON］ VECTORSCOPE ［ON］ ZEBRA ［OFF］ SETUP RETURN TIMECODE DISP ［OFF］ TIMECODE TYPE ［LTC］ TC TALLY ［OFF］ COMPONENT CALIBRATE ＞ RESET TO DEFAULT ＞ Addition for the MENU operation CANCEL / 8COLOR CAL NOW CANCEL / CONFIRM CANCEL / RESET NOW CANCEL / CONFIRM メニューの操作の補足 1 Reset to to the manufacturing default settings 設定値のリセット The user settings can be reset to the manufacturing default settings on
Accessories 付属品 HD View Finder HDF-700, HDF-700SK, HDF-700/S HDF-700＜Contents＞ HDF-700 main component Location stand Universal head VF tilt arm stay BNC cable(1.0 m) Power tap cable(1.2 m) AC adaptor and power cable W1/4 male-male screw adaptor W1/4 arm stay screws(5) Combination washers(2) Rubber washers(4+4(spare)) Nylon washers(1+1(spare)) ＜HDF-700 セット内容＞ HDF-700本体 ロケ用スタンド ユニバーサルヘッド VF チルトアームステー BNCケーブル(1.0 m) カムタップ電源供給ケーブル(1.
Outside View & Dimensions 外形寸法図 HDF-700 外形寸法図 HD View Finder HDF-700 195 50 181.4 (PROTECTOR) 46 147 153 175.3 92.4 (BEZEL OPEN) 100.6 (PROTECTOR) 153.4 (BEZEL OPEN) RETURN MAIN 184.4 195 114.
Specifications 仕様 HD View Finder HDF-700 HDF-700 仕様 LCD パネル LCD Panel TFT-LCD Active Matrix (TN) Panel type LCDパネルタイプ 7.0 inches diagonal Panel size Size of display area 152.4(H) x 91.4(V) mm Panel aspect ratio 16 : 9 パネルサイズ 画面サイズ アスペクト比 Picture Resolution 800(H) x 480(V) x 3(RGB).
TM HDF-700 HDF-700SK HDF-700/S Operating Instructions
