Installation Instructions

一、 /Power ON OFF
【 】Power ON Shitf power switch downwards to make the green part of the switch
visible Thus the transmitter gets into work mode. , .
【 】Power OFF Shitf power switch upwards to make the red part of the switch
visible Thus the transmitter stops working. , .
二、 Main Interface Operation
【 / 】Play Pause In TF mode or computer sound adapter mode short press button , 【 】
can play or pause audio .
【 】Previous In TF mode or compute sound adapter mode short press button to play , 【 】
previous video .
【 】Next In TF mode or compute sound adapter mode short press button to play next , 【 】
video.
【 】Volume Long press button to decrease volume Long press to increase , 【 】 【 】
volume.
【 - 】Start up buit in microphone Hold and press on button to turn on built in - 【 】
microphone When you stop pressing button the microphone will shut off. , .【 】
【 / 】Turn on screen Return Short press butoon can light up the screen and back to 【 】
the main interface .
三、 FM Frepuency Setting
【 】Frequency
Short press button continuously,until appears.Short press or 【 】 【 】 【 】F 1 Frequency
【 】button,the frequency will go forwards 100K each time;
Long press or button,the frequency will go forwards 1MHz each time.【 】 【 】
【 】RF Power
Short press button continuously,until appears.Short press【 】 【 】 【 】F 2 RF Power
button to increase power rate and short press button to decrease power rate.【 】
Attention:In small area usage,for example,in car,low power rate mode is
recommended.
【 】Built in MIC
Short press button continuously,until appears Short press【 】 【 】 【 】F 3 Built in MIC .
or button to go to built in microphone setting mode.【 】
◆ .【 】External MIC means turning off the built in microphone
◆ .【 】MIC ON By Key means turning on built in microphone
◆ .【 】MIC Always ON means the built in microphone is ready all the time
【 】Sound Channel
Short press button continuously,until appears Short press【 】 【 】F 4 Sound Channel .
【 】 【 】or button to set FM sound tracks.
【 - 】Pre emphasis
Short press button continuously,until appears Short press【 】 【 - 】 【 】F 5 Pre emphasis .
or button to set FM pre emphasis time【 】 - .
四、 MP3 Setting
【 】MIC VOL
Short press button continuously,until appears Short press【 】 【 】M 1 MIC VOL .
【 】 【 】button to increase mic volume.Short press to decrease mic volume.
【 】MIC ECHO
Short press button continuously,until appears Short press【 】 【 】M 2 MIC ECHO .
【 】 【 】button to increase echo volume.Short press to decrease echo volume.
【 】MIC Delay
Short press button continuously,until appears Short press【 】 【 】M 3 MIC delay .
【 】 【 】button to increase mic delay.Short press to decrease mic delay.
【 】EQ
Short press button continuously,until appears Short press【 】 【 】M 4 EQ .
【 】 【 】or button can set sound effect for the whole kit.
【 】Repeat
Short press button continuously,until appears Short press【 】 【 】M 5 Repeat .
【 】 【 】or button can set Mp3 cycle mode.
【 】BASS
Short press button continuously,until appears Short press【 】 【 】M 6 BASS .
【 】 【 】or button can set BASS for the whole kit.
【 】TREB
Short press button continuously,until appears Short press【 】 【 】M 7 TREB .
【 】 【 】or button can set tone for the whole kit.
【 】Language
Short press button continuously,until appears Short press【 】 【 】M 8 Language .
【 】 【 】 or button can set Language for the whole kit .
五、 Frequency Saving and Use Saved Frequencies
Turn out your wanted frequency then long press save button until frequency button ,
flashes Thus this frequency is saved When you want to switch to this frequency next. , .
time you just need short press the save button to find it, .
六、 , , ,TF Card Audio Input USB Sound Card Microphone
【 】TF Card Installation Put TF card in card slot follow up the , 【 Main Interface
Operation】
【 】Audio Input play Connect this item to an audio source device with a 3 5mm audio .
cable Main interface will display the connector icon Thus the connection is finished. . , .
【 】USB Sound Card Display Connect this item to a computer with an USB cable Main .
interface will display a computer icon Thus the connection is finished . , .
【 : 】Tip Audio source priority
> > Audio Input USB Sound Card TF Card
【 】External Microphone
Put the external microphone connector to the transmitter s microphone port.The '
main interface displays the microphone icon.It means the connection is successful.
【 】Tips:Microphone Priority
> External microphones Built in microphone
The external microphone must be a 3 step condenser microphone - .
七、Charge
The transmitter can be charged when it is connected to an USB power supply device
by USB cable .
Tips The item can be charged both in on and off mode : .
八、CAUTIONS
◆ .Do not turn on the transmitter when its antenna is not installed
◆
Don not use the transmitter in explosive environment such as gas station and
.oil warehouse
◆ .Please follow local laws and regulation when using this transmitter
◆Repair of this transmitter can only operated by professional technicians.
九、 Technology Parameters
1500
5h
3h
Built-in microphone hole
Charging indicator