User manual

2 Turn the dial to increase the time in
15 minute increments up to 4 hours or decrease
the time to 0 hours. Press START BREW on the
dial to set the new time.
SETTING THE DELAY BREW
1 Plug the brewer in and turn it on by pressing
the Power button.
2 After filling the water reservoir and adding
ground coee to the filter or inserting a pod in
the Ninja Pod Adapter, close the sliding lid or
adapter handle, and place the appropriate-size
vessel under the brew basket.
INTELLIGENT WARMING PLATE
The Intelligent Warming Plate will automatically
turn on during Classic or Rich brews when a
1
/4,
1
/2,
3
/4, or full carafe size is selected. The Intelligent
Warming Plate is set to a specific temperature
setpoint to avoid burning the coee over time. To
turn the warming plate on at any time, turn the dial
to one of the carafe sizes, select Classic or Rich,
and press the KEEP WARM button.
IMPORTANT: The
light on the base
of the brewer will illuminate only
when the warming plate is hot and
will remain illuminated until the plate has
cooled down.
TIME ADJUSTMENT
You can adjust how long the Intelligent Warming
Plate remains on (up to 4 hours).
By default, the Intelligent Warming Plate is set to
remain on for 2 hours. To change the time setting
of your warming plate, follow these instructions:
1 Press and hold KEEP WARM until the clock
begins to flash the current warming time.
NOTE: If you set the warming time to
0 hours, Keep Warm will not automatically
activate during or after a carafe brew cycle,
but you can still turn it on manually by
pressing the KEEP WARM button.
NOTE: The time adjustment setting will be
saved and will not reset when the brewer is
unplugged or loses power.
NOTE: The clock will remain on even if the
brewer is turned o. Ensure the brewer is
powered on to set Delay Brew.
USING THE NINJA® DUALBREW COFFEE MAKER
CONT.
NOTE: The brewer must remain on for
the Delay Brew function to work. DO NOT
power o or unplug after setting Delay Brew.
If the brewer is turned o or unplugged, delay
brew will need to be reset.
3 Press DELAY. DELAY will illuminate and the
clock will begin to flash “12:00” or the last time
that was set.
4 While the clock is flashing, turn the Multi-Serve
dial to adjust the hour. The AM or PM indicator
will illuminate under the clock display as you
are setting the desired time. Press START
BREW on the dial and turn the Multi-Serve dial
to adjust the minute. Press START BREW on
the dial to lock in the time.
5 Once the desired time has been set, use
the Multi-Serve dial to select the size of the
vessel you would like to brew into.
6 Press the BREW STYLE button to choose your
brew style.
7 Once the time, brew size, and brew style have
been set, press the START BREW button
to activate. When activated, the brewer will
beep and DELAY and your selected options
will remain illuminated. To cancel, press
DELAY again.
NOTE: Remember to open the Drip Stop when
you are ready to brew again. If you forget,
your brewer will give you a friendly audible
reminder.
USING THE DRIP STOP
The drip stop is used to close o the brew basket
to prevent any coee from dispensing. You will
need to manually open and close the drip stop
by moving the lever to your desired position. It
can be closed and reopened at any point before,
during, or after a brew.
If you forget to open the Drip Stop, the brewer
will pause the brew, and after 30 seconds it will
give you a friendly audible reminder. After
5 minutes, the brew will be canceled.
CLOSING THE DRIP STOP AFTER A BREW
When the brew cycle is complete, set the Drip
Stop to the closed position to stop dripping from
the brew basket and Ninja Pod Adapter. While
the Drip Stop is closed, the Drip Stop indicator
will illuminate.
NOTE: If the Drip Stop is closed before you
begin a brew, the brewer will notify you with
3 beeps and the Drip Stop indicator will
illuminate. Move the Drip Stop to the open
position and press the START BREW button
to begin your brew.
CLOSED OPEN
14
1-877-646-5288
15ninjakitchen.com