User's Manual

OPERATION GUIDE
1
2
PHENOMENON REASON
The motor alarms
when it is working
PROCESSING METHOD
Charge the battery
The motor is
not running
a，Activate the motor after fully charged
b，Set up the match code
c，Contact the engineers for after-sales
The voltage is low in the
alarm mode
a，The battery is not activated.
b，The emitter is not matched.
c，If press P1 button for a long time
while with no reaction.may be the
power is short-ciralit or the ciralit
board or the motor is broken.
NUMBER
1, The third limit position setting
①After the up limit and down limit setting, you can set the third limit point between them as the half open position;
Press 2s
Press 1s
Press 1s
Press 1s
Press 5sPress 5s
Press 5s Press 1s
Press 1s Press 1s Press 1s
Press 1s Press 1s
Press 1s
Press 1s
Press 5s Press 1s
Press 2s
Press 2s
Press 2s
Press 2s
Press 2s
Run for hint x2
“Di” x3
Run for hint x2
“Di” x3
Run for hint x2
“Di” x3
Run for hint x2
“Di” x3
Run for hint x2
“Di” x3
Run for hint x1
“Di” x1
Run for hint x1
“Di” x1
Run for hint x1
“Di” x1
Run for hint x1
“Di” x1
Run for hint x1
“Di” x1
Run for hint x1
“Di” x1
Run for hint x1
Run for hint x2
“Di” x3
Run for hint x1
Run for hint x2
“Di” x3
Run for hint x1
“Di” x1
Run for hint x1
“Di” x1
“Di” x1
If you need to reverse the rotateon of the motor controlled by the emitter,please run the reverse of direction
setting(as lists in the second point of the P1 button setting)
Up
Stop
Down
Setting
Button specification
P2
P2
P2
4 Add Emitter
P2 →P2 →P2
P2 →P2 →P2
5 Delete one emitter
3 Dot-move/Continuous moving function switch switch
2, The third limit cancel (P2→Stop→Stop)
P1 BUTTON OPERATION
2, Set up limit
3, Set down limit
( Up→Up+Stop)
P2
P2
P2
P2
P2
(Down→Stop+Down)
Run for hint x3
2 The third limit position setting
1 Fine-tune up/down limit position
Enter the limit setting mode
Notes: Repetitive operation dot-move and continuous moving function switching cycle, under the dot-move
function, according to the upor down button more than 2S release motor linkage operation.
P2
M
P2
Lithium Cell
3V
Channel“+”
(P1+)
Channel “-”
(P1-)
P2
or orDot-move Continuous moving
Dot-move function
Continuous moving
function
+
+
+
+
Adjust the new
up limit point
Adjust the new
down limit point
+
Conrm the new up limit point
Conrm the new down limit point
+
+
+
+
or
FACTORY MODE
FACTORY MODE
USER MODE
Functions that can be operated under any mode
Note: After setting up the up and down limit into user mode.
Note: Can not be ne-tune up/down limit position at the same time.
loosen P1
Display
1 Setting up
Run for hint x1
Run for hint x1
loosen P1
Set up is ok
The blind
run down
The blind
run up
The blind
run down
2 The reverse of direction setting
Successful change
the direction
3 limit position
1, Enter the limit setting mode
Conrm the Blind
to stop in the up
limit position
Conrm the Blind
to stop in the down
limit position
The up
limit point
The down
limit point
Set up is ok
Set up is ok
Enter ne-tune
up limit mode
Enter ne-tune
down limit mode
Press 1s
Press 2s Press 2s
Press 1s Press 1s
Press 1s Press 1s Press 1s
Long Press P1
loosen P1
Long Press P1
loosen P1
Long Press P1
loosen P1
Run for hint x2
“Di” x3
Run for hint x2
“Di” x3
Run for hint x2
“Di” x3
Run for hint x1
“Di” x1
Run for hint x1
“Di” x1
Run for hint x1 “Di” x1
Run for hint x1
“Di” x1
Run for hint x1
“Di” x1
Dot-move Continuous moving
or
or
or
or
Press 1s
Press 1s Press 2s
Press 1s Press 2s
Press 2s
Already set
up, down
limit position
Any
position
The third limit position
(any position)
The motor
stops
Set up is ok
Set up is ok
②Long press the stop button for 2s,the roller blinds will move to the third limit
Method two
Method one
Note:Emitter is the one already matched code, while emitter has not
Emitter adding is ok
Emitter adding is ok
One emitter
is deleted
Note:With the same method,you only can delete the emitter not the emitter
1, Activate motor for the rst time
2, The reverse of direction setting
3, Restore factory settings
Run for hint x1
Run for hint x2
“Di~~”x1
“Di”x2
“Di”x3
Set up is ok
Successful change
the direction
Activate is ok
FAULT AND SOLUTION
Recharger or
solar rechargeable
board port