User's Manual

Stop×1
×
1Stop×1
Stop
×
S
top
×
1
P2×1P
2
×
1
Up×1
Beep once
Run for hint
A
Additional
function
Crown installation
Forbidden drill
through crown and
inner gear wheel
Crown
A
Additional
function
Drive adapter installation
A
Additional
function
Bracket installation
A
Additional
function
Rechargeable Description
If the motor already experienced match code,
the memory will be cleared if do it again
If you have matched the codes,connect to the
power, the motor will work normally, if not,the
motor will beep 1 time and turn to remind you entry
P2×1
P2
×
1
P2×1
motor alread
y
exp
erie
e
mor
y
wi
ll
b
e c
l
ear
ed
h
ave matc
h
e
d
t
h
e
co
t
h
e motor wi
ll
wo
rk
w
i
ll
b
eep 1 time an
d
t
ur
If t
he
t
h
e
me
I
f
y
ou
powe
r,
moto
r w
Set up is ok. The
up limit button
control the motor
clockwise.
OK
Set up is ok. The
down limit button
control the motor
clockwise.
OK
Press setting button of
the motor for 2s.loose it
A
Additional
function
Setting up
During the settings, the time between
two operation must be shorter than 6s,
otherwise it will quit the setting
Beep 6 times
Run for hint
Beep 6 times
Run for hint
Beep once
Run for hint
Beep once Beep once
Beep once
Run for hint
Beep once
Run for hint
Beep once
Run for hint
Beep once
Run for hint
Beep 3 times
Run for hint
Beep 3 times
Run for hint
Bee
Run
P2×1
e
hint
Up
×
1
B
ee
p
onc
e
R
un for
h
ep
onc
e
n
for hint
P2×1 Up×1
×
1
Up
×
1
Stop×1
Stop×1
S
to
p
×
1
A
Additional
function
Set up / down
limit position
Run for hint
Run for hint
p
S
to
p
×
1
Run
for
hint
Run
for hint
OK
ķ It is invalid when the up limit and down limit are at the same location
ĸ After limit settingˈwith power and memory function;
Ĺinto the match-code status 2 minutes later, it will quit out the setting limits status automatically
Stop×5Stop×5
Confirm the Blind
to stop in the
down limit position
The up
limit point
The down
limit point
The motor stops
The motor stops
Setting is ok
Setting is ok
Setting is ok
Confirm the Blind
to stop in the up
limit position
Down×1
Beep 4 times
Run for hint
Beep once
everytime
Beep once
everytime
Beep once
Run for hint
OK
Stop×1
Stop×1 Stop×1
The motor stops
ķ After the up limit and down limit setting, you can set the third limit point between them as the half open position;ĸ The third limit
point will be cancelled as the cancellation of limit and code matching;ĹLong press the stop button for 3s,the roller blinds will move to
the third limit, if the motor is in the dot-move status, long press the stop button for 3s,the motor will move to the down limit firstly,
then move to the third limit.
The third limit position setting
A
Additional
function
The third limit position setting
Already set up, down
limit position
The up
limit
position
The down
limit
position
The third
limit position
（any position）
Every time interval
not less than 1 second
The motor has a built-in battery,using the
charger DC264(1.0Nm and 1.1Nm motor) to
recharge.You can also use solar panels DC683B
to charge;when the battery is low, insert the
charge,charger light shows red light.batteries is
full when the red light turns to green.
Beep 3 t
i
me
s
Run
f
o
r hint
Stop
×
×
1
E
ver
y ti
me in
not
less than
o
nce
o
r hin
t
op
p
s
OK
Already set up, down
l
imit position
p
limi
t
p
os
i
t
i
on
e d
o
w
n
l
imi
t
p
os
i
t
i
on
The thi
rd
l
imit
p
ositio
n
（
an
y
position
）
）
B
eep onc
e
R
Run
for hint
Stop
×
The
m
B
eep
o
Run
fo
1
m
otor st
o
P2×1
The third limit position cancelled
Power on
Up×1
Down×1
ᴺIn the process of adjusting the up / down limit: when the motor moving up or down, press the setting button once, the motor
will be under the step-moving status,press the setting button again to quit the step-moving status
ᴻThe step-moving status: themotor will run up or down by the way of step-moving so that the limit position can be adjusted
more correctly
DC264
DC683B