User's Manual

ManualsBrandsNINGBO DOOYA MECHANIC & ELECTRONIC TECHNOLOGY ManualsElectronicsTubular Motor

OPERATION GUIDE

PHENOMENON REASON

The motor alarms

when it is working

PROCESSING METHOD

Charge the battery

The motor is

not running

a，Activate the motor after fully charged

b，Set up the match code

c，Contact the engineers for after-sales

The voltage is low in the

alarm mode

a，The battery is not activated.

b，The emitter is not matched.

c，If press P1 button for a long

time while with no reaction.may

be the power is short-ciralit or the

ciralit board or the motor is

broken.

NUMBER

1, The third limit position setting

①After the up limit and down limit setting, you can set the third limit point between them as the half open position;

Press 2s

Press 1s

Press 5sPress 5s

Press 5s Press 1s

Press 1s Press 1s Press 1s

Press 1s Press 1s

Press 1s

Press 5s Press 1s

Press 2s

Run for hint x2

Run for hint x2Run for hint x1Run for hint x1

Run for hint x1 Run for hint x1 Run for hint x1

Run for hint x1Run for hint x1

Run for hint x2Run for hint x1

Run for hint x1 Run for hint x1

If you need to reverse the rotateon of the motor controlled by the emitter,please run the reverse of

direction setting(as lists in the second point of the P1 button setting)

Stop

Down

Setting

Button specification

4 Add Emitter

P2 →P2 →P2

5 Delete one emitter

3 Dot-move/Continuous moving function switch switch

2, The third limit cancel (P2→Stop→Stop)

P1 BUTTON OPERATION

2, Set up limit

3, Set down limit

( Up→Up+Stop)

(Down→Stop+Down)

Run for hint x3

2 The third limit position setting

1 Fine-tune up/down limit position

Enter the limit setting mode

Notes: Repetitive operation dot-move and continuous moving function switching cycle, under the

dot-move function, according to the upor down button more than 2S release motor linkage operation.

Lithium Cell

Channel“+”

(P1+)

Channel “-”

(P1-)

or orDot-move Continuous moving

Dot-move function

Continuous moving

function

Adjust the new

up limit point

Adjust the new

down limit point

Confirm the new up limit point

Confirm the new down limit point

FACTORY MODE

USER MODE

Functions that can be operated under any mode

Note: After setting up the up and down limit into user mode.

Note: Can not be fine-tune up/down limit position at the same time.

loosen P1

Display

1 Setting up

Run for hint x1

loosen P1

Set up is ok

The blind

run down

The blind

run up

The blind

run down

2 The reverse of direction setting

Successful change

the direction

3 limit position

1, Enter the limit setting mode

Confirm the Blind

to stop in the up

limit position

Confirm the Blind

to stop in the down

limit position

The up

limit point

The down

limit point

Set up is ok

Enter fine-tune

up limit mode

Enter fine-tune

down limit mode

Press 1s

Press 2s Press 2s

Press 1s Press 1s

Press 1s Press 1s Press 1s

Long Press P1

loosen P1

Long Press P1

loosen P1

Long Press P1

loosen P1

Run for hint x2

Run for hint x2Run for hint x1Run for hint x1

Run for hint x1

Dot-move Continuous moving

Press 1s

Press 1s Press 2s

Press 2s

Already set

up, down

limit position

Any

position

The third limit position

(any position)

The motor

stops

Set up is ok

②Long press the stop button for 2s,the roller blinds will move to the third limit

Method two

Method one

Note:Emitter is the one already matched code, while emitter has not

Emitter adding is ok

One emitter

is deleted

Note:With the same method,you only can delete the emitter not the emitter

1, Activate motor for the first time

2, The reverse of direction setting

3, Restore factory settings

Run for hint x1

Run for hint x2

Set up is ok

Successful change

the direction

Activate is ok

FAULT AND SOLUTION

Recharger or

solar rechargeable

board port