HSC 585 MULTI EXTRACTOR 220 - 240V EU INFORMATION & OPERATING INSTRUCTIONS CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL 11600205211REVA -1- 26022008 10.22.
IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops, and offices other than normal residential housekeeping purposes. When using any electrical appliance, basic precautions should always be followed, including the following: NOTE: Read all instructions before using this machine. WARNING! To reduce the risk of fire, electric shock, or injury: • Do not leave the machine unattended when it is plugged-in.
INSPECTION: Carefully unpack and inspect your HSC 585-MULTI for shipping damage. Each machine is tested and inspected before shipping. Any shipping damage incurred is the responsibility of the carrier. You should notify the carrier immediately if you notice damage to the box or to the machine or parts. CLEANING SOLUTIONS: Select a proper pre-spray for the surface to be cleaned, and apply the pre-spray.
KNOW YOUR MACHINE HSC 585 MULTI Vacuum Hose Connection Drain Hose Drain Hose Cap Wand Holder Vacumm Tank Lid Switches Vac Tank 85 Bar Quick Disconnect Hoses Solution Tank Auto Dump Pump Power Prime Pedal Garden Hose Connector Power Cord Wheel Wheel Base Compartment Latch Castor with Brake Pressure Gauge 7 Bar Quick Disconnect HIGH PRESSURE PUMP LIGHT (NO HEAT) SWITCH PLATE I 5 I I I O O I O HEAT SELECTED LIGHT 2 PUMP/HEAT SELECTOR SWITCH 3 VACUUM ON/OFF SWITCH 4 100 PSI PUMP ON
OPERATION REFER TO THE DIAGRAMS ON THE PREVIOUS PAGE CAUTION: Never leave the 85 bar pump running if you are not actively using it CAUTION: IF FOAM OR WATER COMES OUT THE VACUUM EXHAUST, TURN THE MACHINE OFF IMMEDIATELY HIGH PRESSURE WASHER 1 Before each use, inspect the machine, hoses, and cleaning tools for cleanliness and completeness. Make sure hoses are in good condition and the spray nozzle(s) is tight. REFER TO THE AUTO-FILL AND AUTO-DUMP INSTRUCTIONS ON THE FOLLOWING PAGES. 2.
HIGH PRESSURE continued water to a clear, solid stream. Priming may take 20 - 60 seconds, or even longer sometimes, and it will require a full solution tank. When the pump is primed, let off the Power Prime Pedal, and turn off the pump and the vacuum. Then press the Power Prime Pedal once again, for a moment, to release the line pressure; you will hear a ‘swoosh’ of air as the back pressure in the lines is released.
LOW PRESSURE AND HEAT continued 3. If you choose to use the auto-fill feature, connect the fill-hose to the hose connection over the solution tank fill hole. Turn on the water source, and allow the tank to fill with solution. NOTE: do not turn the water on to full pressure; water flowing into the auto-fill system does not need a lot of pressure behind it. If you choose not to use the auto-fill system, just fill the tank with water and cleaning chemical.
USING THE AUTOMATIC-FILL AND/OR AUTOMATIC-DUMP AUTOMATIC-FILL INSTRUCTIONS Operation: 1. Attach a garden hose to the auto-fill hose connection above the holding tank fill hole, and connect the other end of the hose to your water source. 2. Make sure the float that hangs into the solution tank from the auto-fill valve is free of obstruction and can move freely. 3. Turn on the water supply. Do NOT turn the water on full pressure. This system does not require a high presssure water source.
AUTOMATIC-DUMP INSTRUCTIONS Operation: 1. Before each use: if necessary, unscrew the stainless steel filter inside the recovery tank and clean it. Also make sure the float in the recovery tank is clean. 2. Attach a garden hose to the automatic pump-out fitting on the back of the base of the machine (refer to illustration below). 3. Run the other end of the hose into a drain. 4. Turn on the switch for the automatic pump-out (switch is located on the switch panel on the top of the machine).
1 2 5 3 4 6 14 7 23 9 12 8 34 11 10 24 17 21 13 19 16 25 20A 20 15 26 37 30 21A 31 29 27 18 22 28 23 HSC 585 Multi REV A 3.8.
HSC 585 MULTI PART LIST 220 - 240V ITEM QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 16 1 17 1 18 1 19 1 20 1 20A 1 21 1 21A 1 22 1 23 1 24 1 25 1 26 1 27 1 28 1 29 1 30 1 31 1 32 1 33 1 34 1 PART No.
ACCESSORIES HFT-40 TURBO HARD SURFACE TOOL 600305899 Use on all types of hard flooring Cleaning capacity is up to 93 m2 or 1000 ft2/Hr Lightweight, but robust Brush ring attachment No wheels to restrict 360° travel Water temperature up to 110 °C / 230 °F Patented automatic vacuum compensator leaves the floor dryer • In line filter keeps spray jets clean • • • • • • • • • • • • HFT-45 HARD SURFACE COMBO TOOL HFT-43 MINI TURBO HARD SURFACE TOOL 60070045 60070043 Designed for edging hard surfaces Hose
MX 585 MULTI SPECIFICATIONS: Vacuum: Rated Power: Pump: Suction Power: Vacuum at Nozzle: Heat: Suction Width: Weight: Dimensions: 3-stage 2950 W maximum Positive displacement, 83 bar & Demand,7 bar 372 W 30.4 KPA to 100 ºC 38 mm 89.
