DS00351ACN/IRH610 12/11/03 4:57 PM Page 2 I N S TA L L AT I O N & O P E R AT I O N G U I D E IRH610 INFRARED SENSOR EXPANSION HUB B L E N D I N G H I G H F I D E L I T Y A N D A R C H I T E C T U R E ®
DS00351ACN/IRH610 I 12/11/03 N F R A R E 4:57 PM D S E N Page 3 S O R E X P A N S I O N H U B IRH610 Infrared Sensor Expansion Hub Introduction TABLE OF CONTENTS Introduction 1 Features and Benefits 2 Installation Considerations 2 Installation 3 Specifications 6 Contents 6 The IRH610 is an infrared sensor expansion hub that mounts in a structuredwiring cabinet or on a wall. It connects between the output of an infrared sensor and a Niles main system unit.
DS00351ACN/IRH610 I 12/11/03 N F R A R E 4:57 PM D S E N Page 4 S O R E X P A N I O H N Infrared Sensor Inputs Features and Benefits The IRH610 offers a number of improvements over other infrared expansion hubs: S INPUT 1 INPUT 2 U B Output to MSU INPUT 3 OUTPUT TO MSU • Rustproof, weather-resistant housing of highimpact, injection-molded plastic. IRH610 IR EXPANSION HUB POWER STATUS • Removable connector blocks for convenient wire connections.
DS00351ACN/IRH610 I 12/11/03 N F R A R E 4:57 PM D S E N Page 5 S O Mounting Location The IRH610 is specifically designed to conveniently fit into a structured wiring cabinet with snap-in “Christmas Tree” plugs or it can also be wall mounted in an unobtrusive location. Installation 1. Run all necessary wiring to the IRH610. Label the wires for future reference. 2. Secure the IRH610 in a suitable location.
DS00351ACN/IRH610 I 12/11/03 N F R A R E 4:57 PM D S E N Page 6 S O E R MSU250 Main System Unit (Cable runs over 500' not recommended) X P A N S I O N H U B 12VDC Power supply (not supplied) plugged into an outlet INPUT 1 INPUT 2 INPUT 3 OUTPUT TO MSU IRH610 Expansion Hub IRH610 IR EXPANSION HUB POWER STATUS INPUT 4 INPUT 5 INPUT 6 +12V DC Infrared Sensors Figure 3 Wiring Diagram (Installed in an MSU250 System) 4
DS00351ACN/IRH610 I 12/11/03 N F R A R E 4:57 PM D S E N Page 7 S O 7. Plug the connectors into the IRH610 as shown. (Figure 2) The single connector plug at the upper right is the output to the main system unit. The other connector plugs are the inputs, each leading from a specific infrared sensor. See (Figure 3). For an operational overview of your infrared repeater system refer to your main system unit manual (MSU140, MSU250, MSU480, MSU440Z).
DS00351ACN/IRH610 I 12/11/03 N F R A R E 4:57 PM D S E N Page 8 S O R E X P A N S I O N H U B Specifications Contents Mounting • IRH610 Infrared Sensor Expansion Hub X1 In a structured-wiring cabinet, using convenient snap-in “Christmas tree” plugs (supplied) On a wall or other flat surface, secured with drywall screws (not supplied) • Snap-in “Christmas Tree” plugs X2 • Removable connector X7 Wiring Requirements Individual home-runs of category 5 cable from each infrared
DS00351ACN/IRH610 12/11/03 4:57 PM Page 1 Niles Audio Corporation www.nilesaudio.com 12331 S.W. 130 Street Miami, Florida 33186 Tel: (305) 238-4373 Fax: (305) 238-0185 ©2004 Niles Audio Corporation. All rights reserved. Niles, the Niles logo, and Blending Technology and Architecture are registered trademarks of Niles Audio Corporation. Decora is a registered trademark of Leviton Manufacturing. All other trademarks are the property of their respective owners.
