En Wireless Transmitter SY LINK BU POWER LOCK User's Manual
Table of Contents Introduction................................................................................................. 1 Declaration of Conformity ........................................................................ 1 For Your Safety........................................................................................... 2 WARNINGS ................................................................................................ 3 Symbols and Conventions ........................................
Introduction Thank you for purchasing a WT-1 wireless transmitter for compatible Nikon digital cameras. When connected to the camera, the WT-1 can be used to transmit images from the camera memory card to a server. This manual describes how to transmit images from the camera to a server via wireless LAN. Before using the WT-1, be sure to read the “Declaration of Conformity” (pp. 1–2) and “For Your Safety” (pp. 2–3). Declaration of Conformity U.S.A.
CAUTION Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Nikon Corporation may void the user’s authority to operate the equipment. Notice for customers in the State of California, U.S.A. WARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Nikon Inc.
WARNINGS Do not disassemble Failure to observe this precaution could result in fire, electric shock, or other injury. Should the product break open as the result of a fall or other accident, disconnect the camera power source and take the product to a Nikon-authorized service representative for inspection. Turn camera off immediately in the event of malfunction Should you notice smoke or an unusual smell coming from the equipment, immediately remove the battery from the camera, taking care to avoid burns.
Symbols and Conventions The following symbols and conventions are used throughout this manual: This icon marks notes, information that should be read before using the device. This icon indicates that more information is available elsewhere in this manual. Notices • No part of the manuals included with this • Nikon will not be held liable for any product may be reproduced, transmitted, damages resulting from the use of this transcribed, stored in a retrieval system, product.
Wireless Networks C Wireless access point 1 2 WT-1 FTP server C L C Infrastructure S A/V OUT DC IN POWER Ad-hoc LINK BUSY LOCK FTP server (with wireless LAN adapter) WT-1 3 1 FTP ( 25–29) 2 Wireless LAN ( 3 Wireless LAN ( 18–21), TCP/IP ( 18–21), TCP/IP ( 21–25) 21–25), FTP ( 25–29) The WT-1 wireless transmitter is a wireless LAN adapter that allows photographs to be uploaded from the camera to an ftp server.
Setup Parts of the WT-1 Mounting screw Power contact Knob SY LINK BU POWER Housing Status LEDs: POWER (green), LINK (orange), BUSY (green) LOCK USB cable Standard antenna (WA-S1) Antenna connector Tripod socket WA-E1 extended range antenna (available separately) 6 BL-2 battery-chamber cover (for camera battery chamber)
Attaching the WT-1 1 Turn the camera on. 2 Before connecting the WT-1, set the USB option in the camera setup menu to PTP. SET UP USB Mass Storage OK PTP 3 Turn the camera off. 4 Remove the cover protecting the camera power contact. 5 Place the camera on the WT-1 and rotate the knob in the direction shown to fasten the WT-1 to the camera tripod mount. 6 Y LINK BUS POWER LOCK Connect the USB cable to the camera USB connector.
Wireless LAN Setup The Wireless LAN option in the camera setup menu is available when the WT-1 is attached. See the “Menu Guide” ( 00) for details. Option Transceiver Status Auto send SET UP Wireless LAN Transceiver Status Auto send Send file as: Send folder Deselect all? Network settings OFF OFF RAW+J Description Turn wireless LAN transceiver on or off. 00–00 Shows status of link between server and WT-1. 00–00 Choose whether to send pictures to server as they are taken.
Uploading Images Preparation 1 Insert the memory card containing the pictures to be sent. 2 1 2 Turn the camera on. 3 Adjust network settings ( 4 5 00). SET UP Voice memo protect Voice memo button Audio output USB Dust Off ref photo Battery Info Wireless LAN Firmware Version Select On for the Wireless LAN > Transceiver option in the camera setup menu ( 00). Select Status from the Wireless LAN menu and confirm that “Connected” is shown for “Status” ( 00).
Uploading Images 1 2 Select Off for Wireless LAN > Auto send. SET UP Wireless LAN Auto send OFF Off ON On OK Press the button to view pictures on the memory card. Display the first picture to be sent in single-image playback or highlight it in the thumbnail list. 100-1 3 Press the center of the multi selector while pressing the button. The image will be marked with a yellow “send” icon and transmission will begin immediately.
Interrupting Transmission To cancel transmission of images marked with a “send” icon, select the images during playback and press the center of the multi selector while pressing the button. The “send” icon will be removed.
“Send,” “Sending,” and “Sent” Icons The following icons are displayed when images selected for upload are viewed during playback. “Send” Images that have been selected for upload are marked ). If the image is sent with a yellow “send” icon ( icon will turn white. successfully, the yellow 100-1 “Sending” During upload, the icon is displayed in red. 100-1 “Sent” Images that have been uploaded successfully are marked with a white icon.
Network Status The status of the link between the server and the WT-1 is shown by the status LEDs and by the Status display in the Wireless LAN menu. The Status LEDs The POWER LED lights when the WT-1 is receiving power from the camera.
The Status Display Network status can also be viewed by selecting Status from the Wireless LAN menu. Status The status of the link between the server and the camera. Status Link quality Connected Status Link quality Signal level Connected Link quality A five-level indicator of link quality. Signal level A five-level indicator of signal strength. Link quality Signal level Now sending DSC 0001 JPG Signal level Now sending Remaining DSC_0001.JPG 1 Frames Now sending Remaining Time left DSC_0001.
Menu Guide This section describes the options available in the Wireless LAN sub-menu of the camera setup menu. Transceiver Turn the WT-1 transceiver on or off. Option Description Off Transceiver off. Camera can not communicate (default) with server. On Transceiver on. with server.
Auto Send Choose whether to upload pictures to the server as they are taken. Option SET UP Wireless LAN Auto send OFF Off ON On OK Description Off Pictures are not automatically uploaded to server as they are taken. Pic(default) tures can be selected for transmission when camera is in playback mode. On Pictures are uploaded to server as they are taken.* Transmission begins as soon as picture has been recorded to camera memory card. Be sure memory card is inserted in camera before shooting.
Deselect All Remove “send,” “sending,” and “sent” marking from all images on the memory card. SET UP Wireless LAN Deselect all? Option Description No No (default) “Send,” “sending,” and “sent” marking is not removed. Yes Yes Remove “send,” “sending,“ and “sent” marking from all images. Network Settings Adjust settings for connection to the server. Settings created using a computer can be loaded from a memory card ( 00), or network settings can be adjusted individually using the camera menus ( 00).
Load Settings File Network settings created with a computer can be saved to the camera memory card. To load these settings into the camera, highlight Load settings file? and press the multi selector to the right. Press the multi selector up or down to highlight the desired option and press to make a selection. Option SET UP Wireless LAN Load settings file? No OK Yes Description No Exit without changing settings. Yes Load Wireless, TCP/IP, and FTP settings from the memory card.
Communication Mode To choose a mode according to how the wireless network is set up, highlight Communication mode in the wireless menu and press the multi selector to the right. Press the multi selector up or down to highlight to make a selection the desired option and press and return to the wireless menu. Option SET UP Wireless LAN Communication mode OK Infrastructure Ad-hoc Description Infrastructure Connection to wireless network is via access point.
Encryption 1 Highlight Encryption. SET UP Wireless LAN Wireless Communication mode SSID Encryption Channel 2 SET UP Wireless LAN Encryption Done □ On □ Base 16 □ 128 bit OK XXXXX Menu of encryption options displayed. Press multi selector up or down to highlight option, press to right to select. • Done: Save changes and exit to wireless menu. • On: Enable or disable encryption. ✔ appears when encryption is enabled. • Base 16: Enable or disable base-16 encryption.
Channel* 1 2 SET UP Wireless LAN Wireless SET UP Wireless LAN Channel Communication mode SSID Encryption Channel 01 Highlight Channel. 3 Display channel menu. 4 SET UP Wireless LAN Channel 01 Choose channel.† OK SET UP Wireless LAN Wireless Communication mode SSID Encryption Channel OK Return to wireless menu. * Not required if Infrastructure is selected for Communication mode. † The WT-1 offers a choice of thirteen channels (1-13), the WT-1A a choice of eleven channels (1-11).
IP Address* 1 Highlight Obtain automatically. SET UP Wireless LAN IP address Done Obtain automaticallySet Address 000.000.000.000 Mask 000.000.000.000 2 SET UP Wireless LAN IP address Done Obtain automaticallySet Address XXX.XXX.XXX.XXX Mask YYY.YYY.YYY.YYY 3 Turn ✔ on or off. If wireless network is configured to supply IP address automatically, turn ✔ on and proceed to Step 7. Otherwise remove ✔ and enter IP address and subnet mask provided by network administrator (Steps 3–6).
Gateway 1 Highlight Use gateway. SET UP Wireless LAN Gateway Done Use gateway Set Address 000.000.000.000 2 SET UP Wireless LAN Gateway Done Use gateway Set Turn ✔ on or off. If network requires gateway address, turn ✔ on and enter address provided by network administrator (Steps 3–6). Otherwise remove ✔ and proceed to Step 7. Address 000.000.000.000 3 4 SET UP Wireless LAN Gateway Done Use gateway 000.000.000.000 Highlight Address. SET UP Wireless LAN Gateway Set Enter edit mode.
DNS 1 Highlight Enable DNS. SET UP Wireless LAN DNS Done Enable DNS Set Address 000.000.000.000 2 SET UP Wireless LAN DNS Done Enable DNS Set Address 000.000.000.000 3 Turn ✔ on or off. If network requires DNS (Domain Name Server) address, turn ✔ on and enter address provided by network administrator (Steps 3–6). Otherwise remove ✔ and proceed to Step 7. 4 SET UP Wireless LAN DNS Done Enable DNS 000.000.000.000 Highlight Address. SET UP Wireless LAN DNS Set Enter edit mode.
MAC Address This field lists the twelve-digit Media Access Control (MAC) address for the WT-1. SET UP Wireless LAN MAC address 00-00-00-00-00-00 FTP To adjust ftp (file transfer protocol) settings, highlight FTP in the network settings menu ( 00) and press the multi selector to the right. After adjusting settings as described below, press the multi selector to the left to return to the network settings menu.
4 SET UP Wireless LAN Server Address XXX.XXX.XXX. . . Folder Highlight Folder. 6 SET UP Wireless LAN Server 5 SET UP Input + cursor Display text entry dialog ( Folder 26 00). After entering name of destination folder on ftp server, press button to return to server menu. Address XXX.XXX.XXX. . . 7 OK ! " # $ %& ' ( ) * + , – .
User* 1 SET UP Wireless LAN User 2 User ID Password Highlight User ID. 3 SET UP Wireless LAN User SET UP Input + cursor OK ! " # $ %& ' ( ) * + , – . / 0123456789 : ; <= > ? @A B C D E F G H I J K L MN O P Q R S T U VWX Y Z [ ] _ab c de f gh i j k l m nopq r s t u vwx y z { } Display text entry dialog ( 00). After entering user name for login to ftp server, press button to return to user menu. User ID Password 4 SET UP Wireless LAN User User ID XXXXX Password Highlight Password.
Proxy 1 Highlight Use proxy server. SET UP Wireless LAN Proxy Done Use proxy server Set Address 000.000.000.000 0 Port 2 SET UP Wireless LAN Proxy Done Use proxy server Set Address 000.000.000.000 0 Port 3 Turn ✔ on or off. If proxy server is required for ftp, turn ✔ on and enter address and port number (Steps 3–6). Otherwise remove ✔ and proceed to Step 7. 4 SET UP Wireless LAN Proxy Done Use proxy server Address 000.000.000.000 0 Port SET UP Wireless LAN Proxy Set 000.000.000.
Advanced 1 Highlight PASV mode. SET UP Wireless LAN Advanced Done PASV mode Port 2 Set 0 SET UP Wireless LAN Advanced Done PASV mode Port 3 Set Turn ✔ on or off. Turn ✔ on to instruct ftp server to use PASV mode (be sure server supports PASV mode before turning this option on). Turn ✔ off to use normal (PORT) mode. 0 4 SET UP Wireless LAN Advanced Done PASV mode Port SET UP Wireless LAN Advanced Set OK Port 00000 0 Highlight Port. 5 SET UP Wireless LAN Advanced Set Enter edit mode.
Appendices Glossary Ad-hoc Devices in an ad-hoc wireless network communicate directly (“peer to peer”), without a wireless access point. The WT-1 supports an ad-hoc mode for direct wireless connection to an ftp server. BSS-ID (Basic Service Set ID) All wireless devices on an ad-hoc wireless network share the same BSS-ID. The BSS-ID may be up to thirty-two characters long and is case sensitive. See also Ad-hoc.
Protocol A set of rules for passing information back and forth between devices in a network. By defining such elements of communication as how links are established, how receipt of a signal is acknowledged, how data are encoded, and how to handle errors, a protocol ensures that data are transmitted without loss of information. SS-ID An SS-ID prevents interference between devices in different networks. See also BSS-ID, ESS-ID.
Specifications Standards RCR STD-33, ARIB STD-T66 (standard for low power data communications systems) Type IEEE 802.11b (standard wireless LAN protocol); DSSS (IEEE 802.
Index A Access point. See Wireless access point Antenna, 00 Auto send, 00 B BSS-ID, 00 BUSY, 00 C Channel, 00 selection, 00 Connecting the WT-1, 00 Customer support, 00 D Deselect all?, 00 DHCP, 00 Domain Name Server (DNS) address, 00 DNS, 00 E Encryption, 00 key, 00 ESS-ID, 00 F Folders, 00 FTP, 00 ftp, 00 folder, 00 password, 00 PASV mode, 00 port number, 00 proxy, 00 server, 00 settings, 00 user ID, 00 G Gateway, 00 Gateway address, 00 L LAN, 00 LED.