VAA11801-R.3578.A 作成承認印 配布許可印 VAA11801 VAA11802 VAA11803 VAA11804 (J) (U) (EP) (EN) REPAIR MANUAL Recycled paper 再生紙を使用しています Printed in Japan July 2002 Copyright ｃ 2002 by Nikon Corporation. All Rights Reserved.
CONTENTS VAA11801-R.3578.
VAA11801-R.3578.A Specifications Type E5700 digital camera Effective pixels 5.0 million CCD 2/ ” 3 Image size (pixels) Lens high-density CCD; total pixels: 5.24 million • 2560 x 1920 (Full) • 1280 x 960 (SXGA) • 2560 x 1704 (3:2) • 1024 x 768 (XGA) • 1600 x 1200 (UXGA) • 640 x 480 (VGA) 8 x Zoom Nikkor Focal length F = 8.9 – 71.2 mm (35-mm [135] camera format equivalent: 35 – 280 mm) f/-number f2.8 – f4.
VAA11801-R.3578.A Aperture Range Seven-blade iris diaphragm Ten settings in steps of 1/3 EV Sensitivity ISO equivalent approximately 100, 200, 400, 800, or Auto (auto gain to ISO 800) Self-timer Three- or ten-second duration Built-in Speedlight Guide number 12/38.
VAA11801-R.3578.A DISASSEMBLING ! WARNING There are high voltege parts inside. Be careful of this electric shock, when you remove the cover. You must discharge the main condenser according to the instruction of this repair manual before you remove the cover. Notes: ① Remove the battery prior to dissassmbly. ② At disassembling, be sure to memorize how the lead wires were arranged, how the screws were fixed and the type of the used screws.
VAA11801-R.3578.A 2. BACK CABINET ② ⑤ ⑥ ⑤ FPC ⑦ ① ③ ③ ⑪ ④ CONNECTOR ⑧ ③ ⑩ ③ ⑨ • Remove the Hood VF ① . • Remove the screw ② (M1.7 x 2.5) . • Remove the 4 Pieces of screws ③ (M1.7 x 3.5) . • Open the CF card cover ④ . • Remove the 2 Pieces of screws ⑤ (M1.7 x 4) . • Carefully remove the Back Cabinet ⑥ from the camera body . • Remove the FPC ⑦ and the connector ⑧ . • Remove the Back Cabinet ⑥ . • Open the Jack cover ⑨ . • Remove the screw ⑩ (M1.7 x 3), and then remove the Jack Holder ⑪ .
VAA11801-R.3578.A ① ���� �� • Rotate the LCD unit approx. 45 degree in an arrow direction. • Remove the 4 pieces of screws ① (M2 x 3). ① ② ��� �� � �� �� �� � • Remove the back LCD cover ② . • Remove the FPC ③ and connector ④ . ⑧ • Remove the connector ⑤ and the connector, ⑥ . • Remove the 3 pieces of screws ⑦ (M1.7 x 2). • Remove the LCD side holder ⑧ . • Remove the front cover ⑨ .
VAA11801-R.3578.A ③ ② • Remove the LCD ① from the LCD ④ holder. • Remove the 2 pieces of solders ② . • Remove the LCD PCB VF-1 ③ . • Remove the spacer ④ . LCD holder ① 4. JOINT UNIT Joint cover ③ ① ④ A Ⅰ Ⅱ • Remove the joint cover from the joint unit by lifting it up from the bottom. • Remove the 1 piece of screw ① (M1.7 x 4). • Rotate the A of the joint approx. 90 degree in an arrow direction( Ⅰ ). • Remove the 1 piece of screw ② (M1.7 x 2). • Rotate the A of the joint approx.
VAA11801-R.3578.A 5. TOP CABINET ⑨ ② ⑩ ⑧ ① FPC ⑪ ⑨ FPC ⑪ Connector ⑬ FPC ⑫ ⑦ ⑦ ⑤ ③ ④ ⑥ • Remove the screw ① (M1.7 x 2.5). • Remove the 2 Pieces of screws ② (M1.7 x 3.5). • Open the battery cover ③ . • Remove the screw ④ (M1.7 x 3). • Ture the cover grip ⑤ and then remove the screw ⑥ (M1.7 x 4.5). • Remove the screws ⑦ (M1.7 x 4). • Close the SB ⑧ . • Remove the 2 Pieces of screws ⑨ (M1.7 x 4.5). • Carefully remove the top cabinet ⑩ from the camera unit. • Remove the 2 Pieces of FPC ⑪ .
VAA11801-R.3578.A 6. LENS UNIT COVER ⑤ Connector ④ ① FPC ③ ① ⑥ ② ① ② ① ② ① • Remove the 4 Pieces of screws ① (M1.7 x 4). • Remove the 2 Pieces of screws ② (M1.7 x 3.5). • Remove the FPC ③ and the connector ④ . • Carefully remove the SB unit ⑤ from the camera unit. • Carefully remove the Lens unit cover ⑥ from the camera unit.
VAA11801-R.3578.A 7. BATTERY UNIT ⑨ ③ ② ⑫ ③ A ⑬ ⑪ B ⑩ ⑩ B C A ① ⑮ ④ ⑯ ⑥ ⑦ C ⑭ ⑧ ⑤ • Remove the Terminal cover ① . • Remove the screw ② (M1.7 x 3). ⑥ • Remove the 2 Pieces of screws ③ (M1.7 x 4). • Remove the battery cover ④ by pulling it out from the joint part. • Remove the screw ⑤ (M1.7 x 4). • Remove the 3 Pieces of screws ⑥ (M1.7 x 3), and then remove the stand ⑦ . • Carefully come the bottom holder ⑧ to the surface . ⑤ • Remove the C/F card holder ⑨ .
VAA11801-R.3578.A 8. CP-1 PCB, CA-1 PCB, PW-1 PCB ⑭ ⑲ ⑮ ⑳ ④ ⑰ ⑫ ⑩ A ⑪ ③ A ⑯ ⑬ ① ⑤ ⑥ ② ⑱ ⑪ ⑧ ⑨ ⑦ • Remove the screw ① (M1.7x2.5). • Remove the connector ② ,the connector ③ ,and then remove the PW-1 PCB ④ . • Remove the screw ⑤ (M1.7x2.5),and then remove the USB holder ⑥ . • Remove the FPC ⑦ and the connector ⑧ . • Remove the FPC ⑨ . • Remove the screw ⑩ (M1.7x3). • Remove the 2 Pieces of connector ⑪ , and then remove the CP-1 PCB ⑫ . • Remove the 2 Pieces of spacers ⑬ .
VAA11801-R.3578.A 9. LENS UNIT ⑦ ① ② ③ ⑩ ⑨ ⑧ ⑥ Spacer ⑤ ④ Optical filter Spacer • Remove the 2 Pieces of screws ① (M1.7 x 3). • Remove the EVF ② . • Remove the screw ③ (M1.7 x 3). • Remove the speaker holder A ④ , the speaker ⑤ and the speaker holder B ⑥ . • Remove the 2 Pieces of screws ⑦ (M1.7 x 6). • Remove the CA-1 PCB ⑧ from the lens unit. • The spacer, optical filter and spacer can be removed. • Remove the 2 Pieces of screws ⑨ (M1.7 x 2.5), and then remove the CA-1 holder ⑩ . 10.
VAA11801-R.3578.A ASSEMBLY 1. EVF ② • Attach the LCD ① to the finder unit. ① • Align the spacer ② with the position ③ . Affix the spacer,and then bent it in order of ④ , ⑤ Note: When inserting the LCD unit into the finder unit, be careful of the dust, etc. Arrangement of FPC and lead wires Position where the EVF spacer should be attached Affixed position ③ EVF spacer ⑤ ⑤ EVF spacer ④ 2. CCD ③ • Assemble the spacer, mounting lens and CCD to the CA-1 PCB ① . Spacer ② • Attach the screws ② (M1.
VAA11801-R.3578.A 3. LENS UNIT ⑩ ④ ⑨ Spacer Optical filter A Spacer ⑧ ① ② ③ ⑤ ⑥ ⑦ Lens side CCD side Optical filter side CCD side • Attach the CA-1 holder ③ to the lens unit. • Attach the 2 pieces of screws ④ (M1.7 x 2.5). • Assemble the spacer, optical filter and spacer into the lens unit. • Attach the CA-1 PCB ① to the lens unit. • Attach the 2 pieces of screws ② (M1.7 x 6). • Assemble the speaker holder B ⑤ , the speaker ⑥ and the speaker holder A ⑦ . • Attach the screw ⑧ (M1.7 x 3).
VAA11801-R.3578.A 4. CP-1 PCB, PW-1 PCB ⑧ ⑥ ⑦ ④ ⑱ ① ⑤ ⑫ A ⑩ ⑲ A ③ ⑨ 21 ⑯ ⑳ ② ⑪ ⑭ ⑬ ⑮ • Attach the SB unit ① to the condenser holder ② . • Attach the screw ③ (M1.7 x 4). • Attach the TB-2 OCB ④ to the CP-1 PCB ⑤ . • Connect the FPC ⑥ . • Connect the FPC ⑧ of the holder unit ⑦ . Fig.1 • Attach the 2 pieces of spacer ⑨ . • Connect the SB unit ① and CP-1 PCB by the connector ⑩ . • Connect the CP-1 PCB ⑤ and CA-1 PCB by the connector ⑪ . • Attach the screw ⑫ (M1.7 x 3).
VAA11801-R.3578.A Fig.
VAA11801-R.3578.A 5. BATTERY UNIT Position where the battery unit should be attached Arrangement of the lead wires ⑧ ⑭ ⑮ ⑭ A ⑥ ④ ⑦ B ③ ③ B C A ⑯ ② ⑬ ① ⑪ ⑩ C ⑤ ⑨ ⑫ • Attach the microphone ① . • Attach the battery holder ② (Position where the battery unit should ⑪ be attached). • Attach the 2 pieces of screws ③ (M1.7 x 4). • Connect the connector ④ ,connector ⑤ and connector ⑥ . • Attach the spacer ⑦ . • Attach the C/F card holder ⑧ . • Attach the bottom holder ⑨ and the stand ⑩ .
VAA11801-R.3578.A 6. LENS UNIT COVER Arrangement of the lead wires ③ Connector ④ ① ⑥ FPC ① ⑥ ② Arrangement of FPC ① ⑤ ⑥ • FPC ① should be at outside of the lens unit cover. ⑤ ⑥ ⑤ ⑥ • Attach the lens unit cover ② to the camera body. • Attach the SB unit ③ to the camera body. • Insert the FPC ① between the lens unit cover and the camera body ( Arrangement of FPC ① ). • Connect the FPC ① and connector ④ (Arrangement of the lead wires). • Attach the 2 pieces of screws ⑤ (M1.7 x 3.5).
VAA11801-R.3578.A 7. TOP CABINET ⑥ ⑫ ④ ⑤ ⑬ FPC ③ FPC ③ ⑥ Connector ① FPC ② ⑦ ⑦ ⑧ ⑩ ⑪ ⑨ • Connect the connector ① and FPC ② . • Connect the 2 pieces of FPC ③ . • Attach the top cover ④ to the camera body. • Close the SB ⑤ . • Attach the 2 pieces of screws ⑥ (M1.7 x 4.5). • Attach the screw ⑦ (M1.7 x 4). Arrangement of the lead wires • Ture the cover grip ⑧ and then attach the screw ⑨ (M1.7 x 4.5). • Open the battery cover ⑩ • Attach the screw ⑪ (M1.7 x 3). • Open the SB ⑤ .
VAA11801-R.3578.A 8. JOINT UNIT ② Joint cover ④ ① Monitor cover Ⅰ ③ Ⅱ • Attach the TB-1 PCB ① to the joint unit. • Attach the 1 piece of screw ② (M1.7 x 2.5). • Rotate the A of the joint approx. 90 degree in an arrow direction( Ⅰ ). • Attach the monitor cover. • Rotate the A of the joint approx. 90 degree in an arrow direction( Ⅱ ). • Attach the 1 piece of screw ③ (M1.7 x 2). • Attach the 1 piece of screw ④ (M1.7 x 4). • Attach the joint cover.
VAA11801-R.3578.A 9. LCD UNIT ② ③ ① LCD holder ④ • Attach the spacer ① to the LCD holder. • Attach the LCD PCB VF-1 ② . • Solder the 2 pieces of ③ . • Attach the LCD ④ to the LCD holder. �� �� ��� ��� �� � ⑧ ② • Attach the front cover ① to the front LCD cover. • Attach the LCD side holder ② . ⑥ ③ LCD unit ④ • Attach the Joint unit to the front cover ① . • Attache the 3 pieces of screws ③ (M1.7 x 2). • Connect the connector ④ and the connector ⑤ . • Connect the connector ⑥ and the FPC ⑦ .
VAA11801-R.3578.A ⑨ ���� • Rotate the LCD unit approx. 45 degree in an arrow direction. �� • Attach the 4 pieces of screws ⑨ (M2 x 3). ⑨ LCD unit Back cabinet ② Connector ① ⑤ ③ ④ • Pass the connector ① through the hole of the back cabinet and then pull it out to the front side of the rear cover. • Attach the back cabinet to the front LCD unit. • Attache the screws ② (M1.7 x 3.5). • Attache the 2 Pieces of screws ③ (M1.7 x 4). • Attache the 2 Pieces of screws ④ (M1.7 x 3).
VAA11801-R.3578.A 10. BACK CABINET ⑩ ⑧ ⑥ ⑧ FPC ④ ⑦ ⑨ ⑨ ② Connector ⑤ ⑨ ③ ⑨ ① • Attach the Jack cover ① . • Attach the Jack Holder ② and then attach the screw ③ (M1.7 x 3). • Connect the FPC ④ and the connector ⑤ . • Attach the back cabinet ⑥ . • Attach the Hood VF ⑦ . • Attache the 2 Pieces of screws ⑧ (M1.7 x 4). • Attache the 4 Pieces of screws ⑨ (M1.7 x 3.5). • Attache the screw ⑩ (M1.7 x 2.5). 11. SB TOP COVER ② • Close the SB ① . ① • Attach the SB Top cover ② . • Open the SB ① .
VAA11801-R.3578.A ADJUSTMENT 1. Equipment IBM compatible PC • AC adapter EH-21 • USB cable • UC-E1 • Oscilloscope 2. Servicing Tools • Color viewer 5,100 K • Siemens star chart • Calibration software • Chart for color adjustment 3. Adjustment Items and Order 1. Lens Adjustment 2. AWB Adjustment 3. Color Adjustment 4. CCD White Point Defect Detect Adjustment 5. CCD Black Point Defect Detect Adjustment 6. USB Storage information registration 7. LCD Panel Adjustment 7-1. LCD H AFC Adjustment 7-2.
VAA11801-R.3578.A 5. Installing USB drive Install the USB drive with camera or connection kit for PC. 6. Color Viewer Turn on the switch and wait for 30 minutes for aging to take place before using Color Pure. 7. Adjustment items required at replacement of parts Lens Adj. AWB Color Adj.
VAA11801-R.3578.A 9. Calibration software After starting the applicable calibration software, the following is displayed on the PC monitor. 10. Lens Adjustment [Preparation] • Siemens star chart • POWER switch: ON [Adjustment condition] • Make a copy of A4 size siemens chart in enlarged A3 size or larger. • Illumination above the subject should be 400 lux ± 10 %. • Set the siemens star chart 150 cm ± 3 cm (between Siemens star chart and the surface of camera’s protection lens) [Adjustment method] 1.
VAA11801-R.3578.A 11. AWB Adjustment [Preparation] • Color viewer • POWER switch: ON (set to Any MODE) [Note] When setting the camera in place, set it to an angle so that nothing appears in any part of the color viewer except the white section. (Do not enter any light.) [Adjusting method] 1. Double-click on the DscCalDi128. 2. Click the AWB, and click the Yes. 3. AWB adjustment value will appear on the screen. CHECK=128±2, 128±2, 130±30 4. Click the OK.
VAA11801-R.3578.A 12. Color Adjustment [Note] AWB adjustment should always be carried out first. [Adjustment condition] • Set the color adjustment chart to the color viewer. (Do not enter any light.) • Set the color adjustment chart so that it becomes center of the screen. [Adjustment method] • Double-click on the DscCalDi128. • Click the UV Matrix, and click the Yes. • Color adjustment values will appear on the screen. CHECK=0±2, 0±2, 0±2, 0±2 • Click the OK.
VAA11801-R.3578.A 13. CCD White point Defect Detect Adjustment [Adjustment method] • Double-click on the DscCalDi128. • Select the CCD Defect from Test menu of Calibration Soft and click the OK. Refer to FIG-1. • After adjustment, An adjustment value will appear on the screen. Refer to FIG-2. CCD Defect CCD Black 14.
15. USB STORAGE INFORMATION REGISTRATION VAA11801-R.3578.A USB storage data is important for when the camera is connected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be satisfied, so always check and save the USB storage data. [Adjustment method] 1. Connect the camera to a computer. (Refer to 8. Connecting the camera to the computer on the page 12.) 2. Double-click on the DscCalDi128. 3.
VAA11801-R.3578.A 16. LCD Panel Adjustment [VF1 board (Side B)] ����������� �������� �������� �������� ����� ������� 16-1. LCD H AFC Adjustment [Preparation] • POWER switch: ON LCD screen [Adjusting method] 1. Double-click on the DscCalDi128. 2. Select 0 on the LCD H AFC. 3. While watching the LCD monitor, adjust H AFC so that the edge of the LCD adjustment frame are the same distance from the left and right edge of the LCD screen. (A = B) 16-2. LCD RGB Offset Adjustment [Adjusting method] 1.
VAA11801-R.3578.A 16-3. LCD Gain Adjustment [Adjusting method] 1. Adjust LCD “Gain” so that the amplitude of the CL410 waveform is 6.4 V ± 0.2 Vp-p. [Note] 16-2. LCD RGB Offset adjustment should always be carried out first. 16-4. LCD Blue Brightness Adjustment [Adjusting method] 1. Adjust LCD “B Bright” so that the amplitude of the CL412 waveform is VG±0.1 Vp-p with respect to the CL410 (VG) waveform. [Note] 16-2. LCD RGB Offset adjustment and 16-3.
VAA11801-R.3578.A 16-5. LCD Red Brightness Adjustment [Adjusting method] 1. Adjust LCD “R Bright” so that the amplitude of the CL411 waveform is VG±0.1 Vp-p with respect to the CL410 (VG) waveform. [Note] 16-2. LCD RGB Offset adjustment and 16-3. LCD Gain adjustment have done.
VAA11801-R.3578.A 1. OUTLINE OF CIRCUIT DESCRIPTION ����� 1-1. CA1 CIRCUIT DESCRIPTION � 1. IC Configuration IC903 (ICX282AK-B) CCD imager IC904, IC906 (CDX3400N) V driver IC905 (AD9849KST) H driver, CDS, AGC, A/D converter � � �� � �� ������ ��� ���� ���� ���� �� �� ��� ���� ���� ���� ��� �� �� �� � � � � � � � � � ����������������� ��� Fig. 1-1.
3. IC904 and IC906 (V Driver) IC904 and IC906 are vertical clock driver for image sensor. The ternary pulse of V φ 1 (A, B and C) and V φ 3 (A, B and C) for CCD which are output from ASIC (IC102) are generated to add the sensor reading clock (XSG**) and the vertical transfer clock (XV*). V φ 2, V φ 4 and the two pulse of φ SUB for CCD which are output from ASIC (IC102) are generated from vertical transfer clock (XV*). 4.
VAA11801-R.3578.A 1-2. CP1 & VF1 CIRCUIT DESCRIPTION 1. Circuit Description 1-1. Digital clamp The optical black section of the CCD extracts averaged values from the subsequent data to make the black level of the CCD output data uniform for each line. The optical black section of the CCD averaged value for each line is taken as the sum of the value for the previous line multiplied by the coefficient k and the value for the current line multiplied by the coefficient 1-k. 1-2. Signal processor 1.
VAA11801-R.3578.A 1-3. PW1 POWER CIRCUIT DESCRIPTION 1. Power Circuit Outline The switching regulator consists of a DC-DC converter, and it uses a digital power supply, CCD power supply, LCD panel power supply, LED backlight power supply and EVF backlight power supply. The controller is used FA7708R and TK11840L. 1-1.
VAA11801-R.3578.A 1-4. SY-A CIRCUIT DESCRIPTION 1. Configuration and Functions For the overall configuration of the SY-A block, refer to the block diagram. The configuration of the SY-A block centers around a 8-bit microprocessor (IC301). The 8-bit microprocessor handles the following functions. 1. Operation key input, 2. Mode LCD display, 3. Clock control, 4. Power ON/OFF, 5. Storobe charge control, 6. Signal output for lens control of zoom, focus and so on.
VAA11801-R.3578.A Pin 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92~95 96 97 98 99 100 Signal SCK IC XOUT XIN VDD XCIN XCOUT RESET BAT OFF RXD SREQ ZPULSE 1 USB CONNECT CMD IN2 MAIN RESET SCAN OUT 1~4 ASIC TEST ASIC RESET SCAN IN 4 AVSS BATTERY I/O O O I I O I I I I I I I O O O O I I Outline Serial clock output ( → ASIC) Internal connection (connect to VSS terminal directly) Main clock oscillation terminal Main clock oscillation terminal (3 MHz) VDD Clock oscillation terminal (32.
VAA11801-R.3578.A 4. Power Supply Control The 8-bit microprocessor controls the power supply for the overall system. The following is a description of how the power supply is turned on and off. When the battery is attached, a regulated 3.2 V voltage is normally input to the 8-bit microprocessor (IC301) by IC302, so that clock counting and key scanning is carried out even when the power switch is turned off, so that the camera can start up again.
VAA11801-R.3578.
VAA11801-R.3578.
VAA11801-R.3578.
VAA11801-R.3578.A CP-1（レンズ部）ブロック図 CP-1（LENS）BLOCK DIAGRAM UNREGM PON SW REG. IC954 Q9500 L9501 C9515 D9501 VM VDD5 MAIN BLOCK & SYSTEM BLOCK VM VC IC956 FM CW 3 FM OEB 4 FM CKI 28 FM RESETB 30 FOUT1 12 15 OEB A2 MPC17AT85MTP 17 CK B1 FOUT2 13 FOUT3 10 19 FOUT4 11 A1 CW RESETB B2 SW Q9508 ZRESET CN951 LENS BLOCK F.M.
VAA11801-R.3578.A A3001 AL3.2V BACK LIGHT UNREG LCD CN307 13 81 3 4 84 Q3002 X3002 32kHz X3001 3MHz VDD RESET 85 BAT OFF 56 DCINCHK 82 XCIN 83 XCOUT 79 XOUT 80 XIN Q3010 23~26,32~55 EL ON VDD 2 BATTERY BACKUP RESET 1 5 BAT OFF 6 UNREG 8 LI 7 AL3.
VAA11801-R.3578.A CA-1 ブロック図 CA-1 BLOCK DIAGRAM LENS OPTICAL LPF 15V 14 VDD H1 A,B H2 A,B RG 15 16 17 23 24 -7.
VAA11801-R.3578.A PW-1 ブロック図 PW-1 BLOCK DIAGRAM FET SW UPD1915TE 2A PR502 STROBO UNIT UNREG GND PR501 PR503 Battery 2A JK501 2A PR504 2A PR505 2A PR506 2A PR507 2A UNREG AC ADAPTER CN501 EVF ON LCD ON PON 9 6,7,8,31 PA ON ANALOG 5.15V(D) Q5032 5.0V(A) T5001 DC/DC CONVERTER TRANS DISCHARGE CIRCUIT Q5026 15.0V(A) CH1 IC501 QFA7708R Q5027 20 -7.5V(A) 15.15V(F) SWITCHING CONTROL DIGITAL 1.85V CH2 19 Q5009 L5006,C5028 STEP DOWN CIRCUIT 1.85V(D) EVF BL DIGITAL 3.
VAA11801-R.3578.
VAA11801-R.3578.
VAA11801-R.3578.
The contents of inspection standards and tools for E5700 VAA11801-R.3578.A [1] Inspection standards ................................................................................................................................. R1 to R5 [2] Tools ......................................................................................................................................................... T1 to T2 Conditions to be set and prepared for inspections 1.
VAA11801-R.3578.A Inspection standards Item External view Gap/Difference in height Outside and inside status Operation/Operability Operation Operability of buttons Lever/Knob Operation touch Each cover Criteria • General components Gap: 0.3mm or less Difference in height: 0.15mm or less • When the battery cover is closed: Gap: 0.6mm or less (Difference between right and left must not be noticeable.) • Difference in height: 0.3mm or less (Perform measurement under free condition with battery.
VAA11801-R.3578.A Item Monitor Shooting image Lens capacity Focal length Open aperture F No. Peripheral light reduction Ghost/Flare Surface ghost Distortion Dust in a picture Lens barrel Zoom AF Distance measurement operation Shortest photograph distance Normal Macro Criteria Applied tool(s) ・Inclined degree of image shall be 0.5 degree or less.
VAA11801-R.3578.A Item Shooting with a speed light Light adjustment accuracy Guide No. FULL (ISO100•m) Recycling time Lock under uncharged condition Wrong flash Speed light pop-up operation Quality of image Resolution in AF Criteria Applied tool(s) • Tele-end: 0.5~2.7m • Wide-end: 0.5~4.1m In the above range, ± 1Ev or less (ISO: AUTO , • Speed light: Compelling flash, • Exposure: P mode) • 11.5 (+ 0.5/-0.6) EV (Charge for 18 seconds with the new battery and perform measurement within 1 second.
VAA11801-R.3578.A Item Quality of image Reproduction of color Criteria Ｂ Ｗ Ｙｅ Ｒ Ｒ Ｇ Ｂ 190-230 190-230 190-230 190-230 180-210 40- 70 200-220 0- 20 0- 5 Applied tool(s) Color bar chart • Set the conditions as follows: FINE, auto. white balance, center-weighted metering, P mode, sensitivity 100, gradation adjustment standard and profile emphasis standard • Equip the 5100K viewer with the chart and shoot an object in the full range of angle of view.
VAA11801-R.3578.A Item Criteria LCD and others Monitor LCD View Visual field ratio Bright pixels or dim pixels on LCD Applied tool(s) • There must be no shading in the LCD display range. • Inclination between the monitor and the monitor frame must not be outstanding.
VAA11801-R.3578.A Tool List ［２］工具一覧表 ※：新規工具 ※：New tool 名 称 Name 工具番号 Tool No.
VAA11801-R.3578.
VAA11801-R.3578.A 作成承認印 配布許可印 VAA11801 VAA11802 VAA11803 VAA11804 (J) (U) (EP) (EN) PARTS LIST Recycled paper 再生紙を使用しています Printed in Japan July 2002 Copyright ｃ 2002 by Nikon Corporation. All Rights Reserved.
VAA11801-R.3578.
VAA11801-R.3578.
VAA11801-R.3578.
Parts List Part Number E5700 Part Code 名 Part Name 称 Pcs, /Unit VAA11801-R.3578.A Term fig Q'ty/ Main Assembly of Order No.
Parts List Part Number E5700 Part Code 名 Part Name 称 Pcs, /Unit VAA11801-R.3578.A Term fig Q'ty/ Main Assembly of Order No.
Parts List Part Number E5700 Part Code 名 Part Name 636-064-9187 (636-064-9187) 電源回路基板 636-064-9194 (636-064-9194) ＬＣＤ表示基板 636-064-9200 (636-064-9200) 反転ＳＷ基板 636-064-9217 (636-064-9217) バッテリーＳＷ 636-065-0824 (636-065-0824) 636-065-1173 称 Pcs, /Unit VAA11801-R.3578.A Term fig Q'ty/ Main Assembly of Order No.
Parts List Part Number E5700 Part Code 名 Part Name 称 Pcs, /Unit VAA11801-R.3578.A Term fig Q'ty/ Main Assembly of Order No.
Parts List Part Number E5700 Part Code 名 Part Name 称 Pcs, /Unit VAA11801-R.3578.A Term fig Q'ty/ Main Assembly of Order No.
Parts List Part Number E5700 Part Code 名 636-065-7854 (636-065-7854) 中継基板 636-065-8080 (636-065-8080) 636-065-8134 Part Name 称 Pcs, /Unit VAA11801-R.3578.A Term fig Q'ty/ Main Assembly of Order No.
Parts List Part Number E5700 Part Code 名 Part Name 称 Pcs, /Unit VAA11801-R.3578.A Term fig Q'ty/ Main Assembly of Order No.
Parts List Part Number E5700 Part Code 名 Part Name 称 Pcs, /Unit VAA11801-R.3578.A Term fig Q'ty/ Main Assembly of Order No.
Parts List Part Number 645-055-3257 E5700 Part Code 名 Part Name 称 Pcs, /Unit VAA11801-R.3578.A Term fig Q'ty/ Main Assembly of Order No.
