VAA32001-R.3652.A 作成承認印 配布許可印 VAA32001 REPAIR MANUAL Copyright ｃ 2005 by Nikon Corporation. All Rights Reserved.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.A Disassembly � ������� ����������������������������������������������������������������������� �������������������������� ������������������������������������������������������������������ �������������������������������������������������� Points to notice for Lead-free solder products ・ Lead-free solder is used for this product. ・ For soldering work, the special solder and soldering iron are required. ・ Do NOT mix up lead-free solder with traditional solder.
VAA32001-R.3652.A REAR COVER ・ Remove the four screws [#102]. ・ Remove the two screws [#103]. ・ Open the USB cover [#033]. Screw [#102] Screw [#103] USB cover [#033] Screw [#102] ・ As pushing the top side of the rear cover unit [#030] by your finger, perform unhooking. ・ Open the rear cover unit [#030] slowly backward and remove the FPC. Rear cover unit [#030] Rear cover unit [#030] FPC Push. ・ Remove the USB cover [#033].
VAA32001-R.3652.A DISASSEMBLY OF REAR COVER ・ Remove the screw [#104]. ・ Remove the earth shaft [#029]. ・ Remove the cover shaft [#009]. ・ Remove the SD cover [#037].
VAA32001-R.3652.
VAA32001-R.3652.A FRONT COVER ・ Remove the solder at 2 places. ・ Remove the FPC. ・ Remove the two screws [#102]. ・ The earth release [#026] can be removed. FPC Earth release [#026] Screw [#102] Solder ・ Remove the front cover [#013].
VAA32001-R.3652.A DISASSEMBLY OF FRONT COVER ・ Remove the decoration top [#021]. Decoration top [#021] ・ Remove the two screws [#104]. ・ Unhook the battery holder [#024].
VAA32001-R.3652.A ・ Remove the DC cover spring [#012]. ・ Pull out the DC cover [#011]. DC cover [#011] DC cover spring [#012] ・ Take off the spacer [#019] from the release button unit. ※ In the figure below, the spacer is divided into three pieces from the dotted line. ・ Remove the screw [#104]. ・ Remove the release button unit [#020].
VAA32001-R.3652.A Hook TRIPOD SOCKET ・ Perform unhooking and remove the tripod socket [#201]. Tripod socket [#201] LCD[#239] LCD ・ Lift up the LCD [#239] and unsolder the lead wires [red] and [white]. ※ The LCD [#239] is adhered with the double-adhesive tape. ・ Remove the FPC. ・ Remove the LCD [#239]. LCD[#239] Lead wires [red] and [white] FPC SPEAKER HOLDER ・ Take off the spacer [#206]. ・ Unsolder the lead wires [red] and [black]. ・ As turning counterclockwise, remove the speaker holder [#233].
VAA32001-R.3652.A MONITOR HOLDER ・ Remove the two screws [#102]. ・ Remove the earth release [#228]. ・ Remove the three screws [#104]. ・ Remove the LCD holder [#231].
VAA32001-R.3652.A SB UNIT ・ Remove the spacer [#039]. ・ Unsolder the lead wires [gray] and [white]. Spacer [#039] Lead wires [gray] and [white] ・ Unsolder the lead wire [black]. ・ Unsolder the lead wire [pink]. Lead wire [pink] Lead wire [black] ・ Remove the screw [#104]. ・ Float the flash unit [#219].
VAA32001-R.3652.A Screw [#102] WIRE HOLDER ・ Remove the screw [#102]. ・ Remove the wire holder [#215]. Wire holder [#215] TB-1 PCB ・ Perform unhooking and remove the TB-1 PCB [#216]. Hook TB-1 PCB [#216] Wire holder [#215] CONDENSER HOLDER ・ Take off the spacer [#224]. ・ Remove the screw [#102]. ・ Remove the condenser holder [#204].
VAA32001-R.3652.A LENS UNIT ・ Remove the FPC. ・ Take off the spacer [#225]. FPC Spacer [#225] ・ Remove the two screws [#106]. ・ The lens unit can be removed. ・ The spacer LPF [#209], the optical filter [#210] and the spacer [#211] can be removed. ・ Remove the solder fixing the CCD. (Fig. 1) ・ Remove the CCD [#212], the lens mount [#213] and the spacer insulator [#214].
VAA32001-R.3652.A Points to notice when disassembling / (re)assembling Lens unit When the following parts are replaced for repairing the lens unit singularly, the lens unit checking tool is required for the FFD inspection and adjustment.
VAA32001-R.3652.A FINDER UNIT ・ Remove the three screws [#429]. ・ Remove the finder unit [#405]. [#405] Screw [#429] ZOOM MOTOR UNIT ・ Remove the solder of the motor at 2 places. ・ Remove the solder of the FPC at 4 places. ・ Remove the screw [#430]. ・ Remove the zoom PI. Remove the solder. Zoom PI Screw [#430] ・ Remove the screw [#429]. ・ Remove the screw [#431]. ・ Remove the zoom motor unit.
VAA32001-R.3652.A DISASSEMBLY OF ZOOM MOTOR UNIT ・ Pull out the gear shaft D [#419]. ・ Remove the zoom gear E [#411]. ・ Remove the screw [#429] and then remove the gear cover [#403]. Screw [#429] Gear shaft D [#419] Gear cover [#403] Zoom gear E [#411] ・ Remove the zoom gear D [#410] and the zoom gear C [#409].
VAA32001-R.3652.A CCD FRAME ・ Remove the solder. ・ Remove the screw [#430]. ・ Remove the four screws [#431]. Screw [#430] Screw [#431] Solder ・ Remove the lens barrel unit. ・ The finder gear B [#417] can be removed.
VAA32001-R.3652.A BARRIER UNIT ・ Take off the name plate seal [#415]. Name plate seal [#415] ・ Remove the barrier unit [#407] by turning counterclockwise. ※ Insert tweezers into the clearance and turn the barrier unit counterclockwise. It will be removed easily. Clearance Barrier unit [#407] ・ Remove the barrier ring spring [#420]. ・ Remove the barrier ring [#404] by turning clockwise.
VAA32001-R.3652.A FIXED BARREL ・ Take off the FPC sheet [#423]. ・ Push out the turn barrel [#401]. As taking out the shutter FPC, remove the turn barrel [#402]. Turn barrel [#402] FPC sheet [#423] Push out. Shutter FPC Turn barrel [#401] DISASSEMBLY OF FIXED BARREL ・ Pull out the gear shaft A [#413] and remove the zoom gear F [#412]. ・ Pull out the gear shaft B [#418] and remove the finder gear A [#416]. ・ Remove the light-shield ring [#424].
VAA32001-R.3652.A 2ND LENS GROUP UNIT ・ Turn the key barrel unit [#428] in the W-end direction to the limit. ・ The 2nd lens group unit [#426] floats a little and can be removed. 2nd lens group unit [#426] Key barrel unit [#428] SHUTTER ・ Remove the two screws [#431]. ・ Remove the shutter unit [#432]. Screw [#431] Shutter unit [#432] STRAIGHT BARREL ・ Push out and remove the straight barrel unit [#427]. Straight barrel unit [#427] Push out.
VAA32001-R.3652.A KEY BARREL・TURN BARREL ・ Pull out the key barrel unit [#428] from the turn barrel [#401]. Key barrel unit [#428] Shading ring [#424] Turn barrel [#401] 1ST LENS GROUP UNIT ・ Turn the 1st lens group unit [#425] counterclockwise. ・ The 1st lens group unit [#425] can be removed.
VAA32001-R.3652.A ASSEMBLY 1ST LENS GROUP UNIT ・ Set the 1st lens group unit [#425] into the straight barrel unit [#427]. Turn the 1st lens group unit [#425] counterclockwise to be level and turn it clockwise to be installed correctly. ・ Apply the adhesive (1401B) to 3 places. 1401B 1st lens group unit [#425] Straight barrel unit [#427] KEY BARREL・TURN BARREL ・ There is a convex section on the side without gear on the turn barrel [#401].
VAA32001-R.3652.A STRAIGHT BARREL ・ Set the lever of the key barrel unit [#428] at the front side. Set the long hole of the straight barrel unit [#427] at the left side. Fit the convex sections to the grooves and then set the straight barrel unit [#427] into the key barrel unit [#428]. Long hole Straight barrel unit [#427] Convex section Convex section Key barrel unit [#428] Groove Groove Lever SHUTTER ・ Install the shutter unit [#432] and tighten the two screws [#431].
VAA32001-R.3652.A 2ND LENS GROUP UNIT ・ Set the lever of the key barrel unit [#428] at the front side. Set the notch of the 2nd lens group unit [#426] at the left side. Fit the convex sections to the grooves and set the 2nd lens group unit [#426] into the key barrel unit [#428]. Convex section Notch 2nd lens group unit [#426] Convex section key barrel unit [#428]. Groove Groove Lever ASSEMBLY OF FIXED BARREL ・ Set the light-shield ring [#424].
VAA32001-R.3652.A FIXED BARREL ・ Insert the shutter FPC into the hole on the side of the fixed barrel [#402]. ・ Fit the convex sections on the turn barrel [#401] to the grooves on the fixed barrel [#402]. Set the turn barrel [#401] into the fixed barrel [#402]. ・ Adhere the FPC sheet [#423].
VAA32001-R.3652.A CCD FRAME ・ Set the finder gear B [#417] into the lens barrel unit. Then, install the lens barrel unit. Lens barrel unit Finder gear B [#417] ・ Tighten the four screws [#431]. Screw [#431] ・ Insert the FPC of the CCD frame into the boss. ・ Insert the shutter FPC into the boss. ・ Tighten the screw [#430]. ・ Perform soldering.
VAA32001-R.3652.A ASSEMBLY OF ZOOM MOTOR UNIT ・ Set the zoom gear C [#409] and the zoom gear D [#410]. ・ Set the gear cover [#403] and tighten the screw [#429]. Screw [#429] Zoom gear D [#410] Zoom gear C [#409] Gear cover [#403] ・ Set the zoom gear E [#411] and insert the gear shaft D [#419].
VAA32001-R.3652.A ZOOM MOTOR UNIT ・ Fit the zoom motor unit to the bosses on the CCD frame and set it. ・ Tighten the screw [#429]. ・ Tighten the screw [#431]. Screw [#431] Zoom motor unit Screw [#429] ・ Fold the FPC of the zoom PI as shown below and insert the zoom PI. (1) (2) (3) ・ Solder the FPC at 4 places. ・ Solder the motor at 2 places. ・ Tighten the screw [#430]. Perform soldering.
VAA32001-R.3652.A FFD Inspection and adjustment (*FFD:Flange Focal Distance) Preparation ・ Turn the objective glass of the collimator (J19019), and set degree to 0 (0 mm). ・ Set the 0-position of“Adjusting focus stand for APS (J15327)”as follows: 1. Replace the white acrylic plate of the above stand(J15327)with the new one(J15327A) 2. Install J15327D to the micro stand. 3. Align the upper surface of the white acrylic plate of the Adjusting focus stand (J15327A) with the mirror reflecting surface.
VAA32001-R.3652.A ・As shown below, mount the lens-barrel unit on the Adjusting focus stand. Lens-barrel unit Adjusting focus stand for APS (J15327) J15327A J15327D ・ After mounting the lens-barrel unit on the Adjusting focus stand, connect wires (J61202F) of the lens unit inspection tool.
VAA32001-R.3652.A ・Hold the lens-barrel unit lightly with a hand, and run the program for inspecting the lens unit. Note: If the lens-barrel unit is held too tightly, the FFD value cannot be measured correctly. Note: Refer to supplied user manuals of the lens unit checking tool for how to run the program for inspecting the lens unit. ・ On the main menu of the lens unit checking program, click on "FFD Check" icon, and measure the FFD value according to instructions of the PC screen.
VAA32001-R.3652.A BARRIER UNIT ・ Insert the convex section A on the barrier ring [#404] into the clockwise side of the convex section B in the lens barrel. Then, set the barrier ring [#404] and turn it counterclockwise. ・ Set the barrier ring spring [#420]. Barrier ring [#404] Barrier ring spring [#420] Convex section A Convex section B ・ Apply the adhesive (EC-1368) to 4 places on the back of the barrier unit [#407].
VAA32001-R.3652.A ・ Adhere the name plate seal [#415]. Name plate seal [#415] Operation inspection ・ It is possible to check the operation with the lens-barrel driving software at the service facilities equipped with the lens unit checking tool. FINDER UNIT ・ Set the finder unit [#405] at the W-end manually. ・ Tighten the three screws [#429]. ・ Install the finder unit [#405].
VAA32001-R.3652.A Resolution inspection When dissembling and repairing the lens-barrel, be sure to check the following after assembling it into the camera body. ・Resolution inspection By shooting the high-definition resolution chart (J63079), confirm that the number of TV lines is within the standard. TV lines (standard): 1100 TV lines or more in the center; 700 TV lines or more at the periphery (ref.
VAA32001-R.3652.A LENS UNIT ・ Set the spacer LPF [#209] and the optical filter [#210] into the lens unit. ・ As taking care about its direction, set the spacer [#211] into the lens unit. ・ Set the spacer insulator [#214], the lens mount [#213] and the CCD [#212] and solder them to the main PCB CP-1 [#218]. (Fig. 1) ・ Tighten the two screws [#106]. Perform soldering. Main PCB CP-1 [#218] (Fig.
VAA32001-R.3652.A CONDENSER HOLDER ・ Set the condenser holder [#204] and tighten the screw [#102]. ・ Adhere the spacer [#224]. Spacer [#224] Screw [#102] Condenser holder [#204] Spacer [#224] TB-1 PCB ・ Set the TB-1 PCB [#216] onto the hook of the wire holder [#215]. ・ Pass the lead wire of the TB-1 PCB [#216] through the notch of the wire holder [#215]. Hook TB-1 PCB [#216] Wire holder [#215] Notch Screw [#102] WIRE HOLDER ・ Set the wire holder [#215] and tighten the screw [#102].
VAA32001-R.3652.A SB UNIT ・ Arrange the lead wires [pink] and [blue] as shown below. ・ As arranging the lead wire [blue] as shown below (Fig. 1), set the flash unit [#219] and tighten the screw [#104]. (Fig. 2) Flash unit [#219] Lead wire [blue] Screw [#104] (Fig.1) (Fig.2) ・ Arrange the lead wire [pink] as shown below. ・ Solder the lead wire [pink].
VAA32001-R.3652.A ・ Solder the lead wire [black]. ・ Solder the lead wires [gray] and [white]. Lead wires [gray] and [white] Lead wire [black] ・ Arrange the lead wires as shown below. ・ Adhere the spacer [#039].
VAA32001-R.3652.A MONITOR HOLDER ・ Fit the LCD holder [#231] to the bosses, set it and tighten the three screws [#104]. ・ Set the earth release [#228]. ・ Tighten the two screws [#102].
VAA32001-R.3652.A SPEAKER HOLDER ・ Fit the center boss on the speaker holder [#233] into the boss hole on the LCD holder [#231]. Then, turn the speaker holder [#233] clockwise. ・ Solder the lead wires [red] and [white]. ・ Arrange the lead wires [red] and [white] as shown below. Lead wire [white] Lead wire [red] Boss hole position Speaker holder [#233] ・ Adhere the spacer [#206]. Spacer [#206] LCD ・ Set the FPC. ・ Solder the lead wires [red] and [white].
VAA32001-R.3652.A Hook TRIPOD SOCKET ・ Install the tripod socket [#201] by fitting onto the hook. Tripod socket [#201] LCD [#239] ASSEMBLY OF FRONT COVER ・ Install the release button unit [#020] by inserting its convex section A into the notch B on the front cover [#013]. ・ Tighten the screw [#104]. ・ Adhere the spacer [#019] of the release button unit as shown below. ※ The spacer [#019] is divided into three pieces from the dotted line in the figure.
VAA32001-R.3652.A ・ Set the battery holder [#024] by using the hook. ・ Tighten the two screws [#104]. Battery holder [#024] Hook Screw [#104] ・ Set the decoration top [#021].
VAA32001-R.3652.A FRONT COVER ・ Set the front cover [#013]. ・ Set the earth release [#026]. ・ Tighten the two screws [#102]. ・ Perform soldering. ・ Set the FPC. Perform soldering. Earth release [#026] Screw [#102] FPC Front cover [#013] ASSEMBLY OF REAR COVER ・ Set the SD cover [#037]. ・ Set the cover shaft [#009]. ・ Set the earth shaft [#029]. ・ Tighten the screw [#104].
VAA32001-R.3652.A REAR COVER ・ Set the USB cover [#033]. ・ Fold the FPC as shown below and set it. Rear cover unit [#030] FPC USB cover [#033] ・ Set the rear cover unit [#030]. ・ Tighten the two screws [#103]. Screw [#103] Rear cover unit [#030] ・ Tighten the four screws [#102].
VAA32001-R.3652.A ADJUSTMENT 1. Equipment IBM compatible PC/AT • AC adapter EH-62B • USB cable ( UC-E6) 2. Servicing tools • Pattern box • Color meter • Luminance meter • Siemens star chart • Calibration software (J65071) • Adjustment collimator (J63090) or Adjustment firmware 3. Adjustment items and order Adjustment after replacing the CP-1 PCB of RP 1. Writing of the initial image data 2. Firmware up 3. Lens adjustment 4. AWB adjustment 5. CCD white dot defect compensation 6.
4. Initial image data writing and Firmware upgrading VAA32001-R.3652.A Write the data of initial images, and go on to upgrade the firmware. Device ・ AC adapter (EH-62B) ・ Upgrading SD card X 1 [How to create an upgrading SD card] 1) Format SD card on PC. 2) Create a folder named "firmware" in the root directory of the SD card. 3) Copy "firmware.bin" into the created folder. 4) Copy "nanddat.bin" into the root directory of the same SD card.
・ When the data writing is completed, the menu for upgrading will be displayed. (Fig.3) VAA32001-R.3652.A (Fig.3) ・ Select "Yes", and press the decision button to carry out upgrading. (Fig.4) Note: Do NOT turn power OFF during upgrading. (Fig.4) ・ When the screen indicates the completion of upgrading, turn power OFF and remove the SD card. (Fig.5) ・ Turn power ON, and check the version by "Firmware version" on the menu. ・ Turn power OFF to end. (Fig.
VAA32001-R.3652.A 5. Setup 1) System requirements • Windows® 98 or Me, 2000, XP • IBM-compatible PC/AT with Pentium or higher processor • CD-ROM drive • 3.5-inch 2HD diskette drive • USB port • 40 MB or more RAM • Hard disk drive with 15 MB or more memory space • VGA or SVGA monitor with 256 or more color display 2) Installing calibration software • Insert the calibration software installation diskette into the diskette drive. • Open Explorer. • Copy "DscCalDi.exe, Camapi32.
VAA32001-R.3652.A 7. Pattern box Before using the pattern box, turn its power on to carry out "Aging" approx. 30 minutes: the color temperature should be 3100 ± 20K by the adjustment with the color meter, and the luminance should be 900 ± 20cd/m2 by the adjustment with the luminance meter. When using the pattern box and for a while after its power turns off, the lamp and its surroundings are subject to high temperatures, so care should be taken when handling.
VAA32001-R.3652.A 9. Connecting the camera to the computer 1) Insert the camera connector of USB cable in the notch of the camera’s USB port. 2) Connect the cable to the USB port on PC. USBポートへ To USB port USBケーブル （UC-E6） USB Cable (UC-E6) Supply電源はACアダプタEH-62B the power through から供給してください。 the AC adapter (EH-62B). 10. Calibration software ・ Turn on the power switch of the camera. ・ When the calibration software starts, the following is displayed on the PC monitor.
VAA32001-R.3652.A 11. Lens adjustment ※ For the lens adjustment, choose either the infinity adjustment with the collimator or the 1.5-m adjustment with the adjustment firmware. (However, in case of 1.5-m adjustment, the focus may not be sharp at infinity.) 11-1. Infinity adjustment [Preparations] • Turn the power switch of the adjustment collimator (C-DSC) J63090 to on. • Turn the power switch of the camera to on.
VAA32001-R.3652.A 11-2. 1.5-m Adjustment ※ Before performing the 1.5-m adjustment in this machine, write the adjustment firmware on the camera. After adjustment, be sure to write the product firmware. Procedure for setting Adjustment firmware 1) Save the adjustment firmware and the product firmware in any folder. 2) Start up "DscCa1Di.exe" and click on "Firmware" button on the main menu to write the adjustment firmware.
VAA32001-R.3652.A 12. AWB adjustment [Preparations] • Pattern Box(Color temperature: 3100 ± 20K, Luminance: 900 ± 20cd/m2) [Conditions] • Set the pattern box and camera (lens front) at "0cm" distance between them. Note) Do not allow outside light to enter in. [How to] • Double-click on "DscCa1Di.exe". • Click "AWB", then "Yes". • AWB adjustment values will appear on the screen. Judgment standard: CHECK=128 ± 1, 128 ± 1, 130 ± 40 • Click "OK".
VAA32001-R.3652.A 13. CCD white dot defect compensation [Conditions] • With the lens shutter being closed, read the defect of CCD pixels. Then, make the correction data and rewrite the data by the following procedure. Correct the upper level of defective 2000 pixels from the brightest number of CCD pixels.. [How to] • Double-click on "DscCa1Di.exe". • Select "CCD Defect" from Test menu of Calibration Software and click the "OK". Refer to FIG-1.
VAA32001-R.3652.A 15. USB storage information registration USB storage data is important when the camera is connected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specifications will not be satisfied, so always check and save the USB storage data. [How to] • Connect the camera to a computer. • Double-click on the "DscCa1Di.exe". • Click on the "Get" button in the USB storage window and check the USB storage data.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.
VAA32001-R.3652.A CP1(SYA) 回路図 CP1(SYA) CIRCUIT DIAGRAM BLK SYA +12V(B) TO PWA R3021 8.2K;1/16J Y1-69000/SX797-UNK R3022 22K;1/16J C RED E PS1550L B Q3005 2SC5658R PAON2 TO DMA(MAIN) COMREQ PLLEN TO TB1 JW601, JW602 CL307 CHG LED_A WHITE LED_C GRAY LCDON2 TELE WIDE CL301 12 CL302 SI1 PW_LED SI2 SI4C SI4 16 SI3C 18 SI1C 19 SI2C SB.
VAA32001-R.3652.A CP1(CAA) 回路図 CP1(CAA) CIRCUIT DIAGRAM CAA C9028 10;B R9007 3.3;1/16J -8.0V(A) C1-69000/SX797-UNK �������� ���� ����� ��� �� C9026 1;B ���� � ���� ��� ��� 0SUB 5 6 7 8 �� 4 VM 3 VL 2 � 1 XSG2B 0V6 �� IV5 R9013 2.2K;1/16J 10 11 12 13 14 0V8 9 0V2 VM 0V1 V.
VAA32001-R.3652.A CP1(PWA) 回路図 CP1(PWA) CIRCUIT DIAGRAM 2A F5005 F47K2R0C3LFND D9601 SD833-04(SC) R9606 130K;1/16D 3K;1/16J C5035 VDD FB CE D5007 HN2D01JE 4 LDT565620T-**1 (H=2.0) OM/ORPTV008Z S R5036 2125 16V C5032 1;B Q5001 RSR025N03 L5004 3.3;N R5035 47K;1/16J R5034 3 +12V(A) TO DMA(MAIN)& STA 3216 0;1/16Z -8V(A) 2.2K;1/16J G R5040 10K;1/16J 3 1000P;B 3 C5034 2 1 4 IN REG 3.4V VOUT 3.45V(A) 4 IC502 TK11134CS QTK11134CS--J OM/ORTR25Z +3.45V(A) 1;B 6.3V C5020 0.
VAA32001-R.3652.A CP1(STA) 回路図 CP1(STA) CIRCUIT DIAGRAM STA S2-69000/SX797-UNK FLASH REFLECTOR T5402 R5417 10M;1/8F 1.2K;1/16J R5409 TO DMA(MAIN) 3 1 4 5 R5413 10K;1/16J 2 DAN222 R5408 Q5405 CPH5504-E OM/ORTR15Z 2125 CHG TO PWA Q5407 3LN01S-E D5407 3 16V C5401 22;6.3B 4 BLACK H=4.
VAA32001-R.3652.
VAA32001-R.3652.A TB1 回路図 TB1 CIRCUIT DIAGRAM NEW OM/ORLE07AZ H=0.
VAA32001-R.3652.A 総合ブロック図 OVERALL BLOCK DIAGRAM LENS BLOCK CCD BLOCK IC903 5M Pixel IC905 CDS/AGC/AD-C IC901 CCD H. Driver V.
VAA32001-R.3652.A CCD ブロック図 CCD BLOCK DIAGRAM LENS O_LPF -8.0V(A) IC903 VO 9 Q9001 EF 27 AD9948 IC905 CDS, A/D C H. DRIVER D2:11 2:4. 7:13 25 TO CP1(DMA) IC101 ASIC AD0 AD9 ADCK TGHD CCDCK TGVD IC904 CCDSD TK11130CS +3.45V(A) IV1, IV2, IV3, IV4, IV5, IV6 20, 22, 25, 26, 27, 28 ISUB 3 XV4 XV3 XV2 XV1 XSG3 XSG2B XSG1B XSG2A XSG1A CCDEN REG. 3.0V 34, 35 CH1, CH2, CH3, CH4, CH5 1, 2, 21, 23, 24 33 14, 15, 21 17, 22 VCC 19 IC901 6,18 V. DRIVER AN20101A 31 -8.
VAA32001-R.3652.A LENS ブロック図 LENS BLOCK DIAGRAM UNREG IC961 L9601, D9601 Q9601, C9603 BOOST4.25V UNIT LENS SW REG.
VAA32001-R.3652.
VAA32001-R.3652.A IC304 RESET IC 3 2 VDD 4 1 OUT VSS SYSTEM CONTROL ブロック図 SYSTEM CONTROL BLOCK DIAGRAM BOOST4.25V ALWAYS3.2V UNREG BOOST4.25V RESET 5 VDD 6 VDD 23 VDD 12 RESET 8 3 LI 4 BAT OFF AL3.2V 8 1 Q3002 2 IC302 BATTERY BACKUP UNREG 7 5 BACK UP Z3001 21 BATTERY 41 BACKUP_CTL AVREF 43 AV REF ON Q3001 SW3.
VAA32001-R.3652.A POWER ブロック図 POWER BLOCK DIAGRAM CNT6 48 VR501 VR 10 32 17 16 31 29 IC501 FA7723R 35 36 SWITCHING MODULE 24 30 39 40 OUT4 OUT5 OUT7 OUT2D-2 OUT2D-1 OUT1D-2 OUT1D-1 OUT6 IC961 Q9601, L9601 Q9602 STEP UP CIRCUIT T5001,Q5001 CONVERTOR TRANS L5004, Q5004 STEP UP CIRCUIT L5003, Q5003 STEP DOWN CIRCUIT L5005 STEP DOWN CIRCUIT L5006 STEP UP CIRCUIT L5007, Q5002 STEP UP CIRCUIT 4.5V 1.41V(D) Q5006 PON=H:4.25V, PON=L:3.6V IC502 REG. CURRENT DETECTOR CIRCUIT +3.
2 5 WT R1526 RD + 1 L1302 3 4 C1519 C1505 LCD_AN C1512 C1708 R1702 CN171 32 LCD_CA R1502 C1515 C1512 10 10 XF111 R1066 C1051 XF111 R1054 C1101 15 1 R1052 C1056 C1059 R1055 C1058 R1701 D1701 CN193 TDI CN193 R1005 C1003 C1004 L1103 R1104 C1114 R1102 BLK Q5006 C3001 R1703 C1702 C1018 R1902 C1905 C1904 R1046 C1201 R9002 IC904 R1403 R1047 L9001 C9008 C1703 C9008 R9017 10 C1751 R1734 Q3005 R3021 D1703 C1102 X1101 C1706 C1705 D1701 Q1736 C1734 R1736 C11
VAA32001-R.3652.A The contents of inspection standards and tools for E4600 [1] Inspection standards ............................................................................................................................................ R1 to R10 [2] Tools ....................................................................................................................................................................
INSPECTION STANDARDS Item Criteria VAA32001-R.3652.A Applied tool(s) External view Gap/Difference in height ・ General components Visual observation Gap: 0.3mm or less Difference in height: 0.15mm or less ・ When the battery case is opened/closed: Gap in its periphery: 0.3mm or less Gap in the bottom: 0.5mm or less Difference between right and left: 0.2mm or less Stepped difference: 0.
VAA32001-R.3652.A Item Criteria Applied tool(s) Monitor Shooting image ・ Inclined degree of image shall be 0.5 degree or less. Photoshop ・ PC monitor and print output Printer (Output will be evaluated while the display range boundary of LCD unit is regarded as standard when the through-the-monitor image is made.) Lens capacity Focal length Open aperture F No. Wide-end position (Compelling ∞ ) 5.7 mm Focal length + 7.1% measuring instrument - 1.
VAA32001-R.3652.A Item Criteria Applied tool(s) Lens barrel Zoom / Focus ・ There must not be an abnormal action (for example, the unit oper- Visual observation ates one-sidedly or its operation is not smooth or it is caught). (As changing the camera's posture, check it in all the directions.) AF Distance measurement ・ In the case of normal AF: Focus must be fit at the picture center. operation ・ In the case of the out-of-focus object: Focus must be fit at the 2m Visual observation point.
VAA32001-R.3652.A Item Criteria Applied tool(s) Quality of image Resolution in AF The resolution must be in compliance with the following values in EIAJ chart all the postures of the EIA J chart evaluation. Photoshop Siemens chart Center horizontal/vertical: 1100 TV pcs. Periphery horizontal/vertical: 700 TV pcs. Center horizontal/vertical: 1100 TV pcs. Periphery horizontal/vertical: 700 TV pcs. <2M> Center horizontal/vertical: 700 TV pcs.
VAA32001-R.3652.A Item In the case of compelling infinity Criteria (The whole zoom area) Applied tool(s) Infinity chart Center horizontal/vertical: 900 TV pcs. ・ Shoot the infinity collimator image on condition that aperture is "open" in the scene distance view/night view mode and the image quality priority mode. ・ Then, open the recorded image data file through Photoshop and check the resolution visually.
VAA32001-R.3652.A Item Criteria Applied tool(s) Quality of image Noise [Histogram's standard deviation] 5100K viewer ・ Gray: 3.0 or less ITE γ 0.45 Black: 3.5 or less Gray scale (standard) ・ Equip the 5100K viewer with a scale and shoot an object in the Photoshop full range of angle of view while the AUTO mode and the image quality priority mode are set.
VAA32001-R.3652.A Item Criteria Applied tool(s) Finder View / Image ・ There must be no blur, distortion, ghost, halation or other out- Visual observation standing troubles in contrast, gradation, etc. Visual field frame/ frame line ・ Blur or difference in thickness must be within the proper range to Visual observation operate the stamped line and visual field frame. Shading ・ You can check the whole finder visual field.
VAA32001-R.3652.A Item Criteria Applied tool(s) LCD and others Monitor LCD View ・ The reproduction of W, B and RGB must not be interfered. Visual observation ・ The monitor LCD must comply with the SY monitor LCD performance standard. ・ There must be no shading in the LCD display range. ・ The inclination of the image and the monitor frame must be ± 0.75° or less. Visual observation ・ The vertical difference and horizontal difference of the black belt width in the image periphery must be within 0.
VAA32001-R.3652.A Item Criteria Electric characteristics Applied tool(s) Constant voltage Consumption current power supply Stand-by ・ When card is not used: 0.27mA or less (when the power switch is OFF) Ammeter Dummy battery pack ・ When card is used: 0.39mA or less (when the power switch is OFF) Start (Photography) ・ 12mA or less (at "Sleep") ・ 0.75W or less (when the power switch is OFF B.
VAA32001-R.3652.A Item Criteria Electric characteristics When voltage increases (Alkaline battery) Level 1 ・ 2.25 ± 0.1V Level 2 ・ 2.1 ± 0.1V (Ni-MH) Level 1 ・ 2.45 ± 0.1V Level 2 ・ 2.1 ± 0.1V (Li battery) Level 1 ・ 2.6 ± 0.1V Level 2 ・ 2.1 ± 0.1V ・ Connect the constant-voltage power supply to the dummy battery pack and check the voltage at Level 3 ("no battery capacity" indication). Then, turn off the power, increase the voltage by 0.1V and change the power switch from OFF to ON.
VAA32001-R.3652.A ［２］工具一覧表 Tool List ※：新規工具 ※：New tool 工具番号 名 Tool No.
VAA32001-R.3652.A ※：新規工具 ※：New tool 工具番号 名 Tool No.
VAA32001-R.3652.A ※：新規工具 ※：New tool 工具番号 名 Tool No.
VAA32001-R.3652.A ※：新規工具 ※：New tool 工具番号 名 Tool No.
ジーメンススターチャート VAA32001-R.3652.
VAA32001-R.3652.A 作成承認印 配布許可印 VAA32001 PARTS LIST 修 理 部 品 表 Copyright ｃ 2005 by Nikon Corporation. All Rights Reserved.
VAA32001-R．3652.
VAA32001-R．3652.A 636-082-9251(10) 636-082-3952(5) 636-059-0069(5) 636-082-8469(10) 636-082-3884(5) 636-082-8285(1) 636-082-3990(5) 411-177-9503(10) 636-083-4859(5) 636-086-1305(10) 636-084-6432(10) 636-082-3907(5) 636-084-9662(5) 636-083-8116(5) 636-082-8506(5) F2・E4600 Fig.
VAA32001-R．3652.
VAA32001-R．3652.
Parts List Part Number Part Code 1B150-106 1B150-106 409-542-9906 * 409-542-9906 411-177-9503 * 411-177-9503 411-178-9403 * 411-178-9403 411-182-4609 * 411-182-4609 411-186-0409 * 411-186-0409 411-190-8309 * 411-190-8309 412-060-9501 * 412-060-9501 420-002-0202 420-002-0202 423-031-1707 * 423-031-1707 636-059-0069 * 636-059-0069 636-074-2468 * 636-074-2468 636-082-3860 * 636-082-3860 636-082-3877 * 636-082-3877 636-082-3884 * 636-082-3884 636-082-3907 636-082-3907 636-082-3914 * 636-082-3914 E4600 部品名 Bar
Parts List Part Number Part Code 636-082-3921 636-082-3921 636-082-3938 * 636-082-3938 636-082-3952 * 636-082-3952 636-082-3976 * 636-082-3976 636-082-3983 * 636-082-3983 636-082-3990 * 636-082-3990 636-082-4003 * 636-082-4003 636-082-4027 * 636-082-4027 636-082-4034 * 636-082-4034 636-082-4041 * 636-082-4041 636-082-4058 * 636-082-4058 636-082-4065 * 636-082-4065 636-082-4089 * 636-082-4089 636-082-4102 * 636-082-4102 636-082-4119 * 636-082-4119 636-082-4126 * 636-082-4126 636-082-4898 * 636-082-4898 * E4
Parts List Part Number Part Code 636-082-8070 636-082-8070 636-082-8285 * 636-082-8285 636-082-8377 * 636-082-8377 636-082-8445 * 636-082-8445 636-082-8469 636-082-8469 636-082-8490 * 636-082-8490 636-082-8506 * 636-082-8506 636-082-8520 * 636-082-8520 636-082-9244 * 636-082-9244 636-082-9251 * 636-082-9251 636-082-9299 * 636-082-9299 636-082-9442 * 636-082-9442 636-082-9619 636-082-9619 636-082-9626 636-082-9626 636-083-0684 * 636-083-0684 636-083-0998 * 636-083-0998 636-083-1001 * 636-083-1001 * E4600 部品
Parts List E4600 Part Number Part Code Barcode (Part Code) 636-083-1391 636-083-1391 636-083-1414 * 636-083-1414 636-083-1421 * 636-083-1421 636-083-1438 * 636-083-1438 636-083-2930 * 636-083-2930 636-083-3142 * 636-083-3142 636-083-3982 * 636-083-3982 636-083-4750 * 636-083-4750 636-083-4859 * 636-083-4859 636-083-7560 636-083-7560 636-083-7614 636-083-7614 636-083-8109 636-083-8109 636-083-8109-U 636-083-8109-U 636-083-8116 636-083-8116 636-084-0645 636-084-0645 636-084-1550 * 636-084-1550 636-084-483
Parts List Part Number Part Code 636-084-6364 636-084-6364 636-084-6425 * 636-084-6425 636-084-6432 * 636-084-6432 636-084-7378 * 636-084-7378 636-084-7842 636-084-7842 636-084-7859 636-084-7859 636-084-7866 636-084-7866 636-084-9662 * 636-084-9662 636-085-3713 * 636-085-3713 636-085-4000 * 636-085-4000 636-086-1305 * 636-086-1305 636-086-1350 * 636-086-1350 636-086-1367 * 636-086-1367 636-086-5822 636-086-5822 636-086-5839 636-086-5839 636-086-5846 636-086-5846 636-086-6843 636-086-6843 * E4600 部品名 Barco
Parts List Part Number Part Code 636-087-1410 636-087-1410 636-087-1649 * 636-087-1649 645-054-4163 * 645-054-4163 645-057-4726 * 645-057-4726 645-064-7970 * 645-064-7970 645-070-8398 * 645-070-8398 645-072-1151 645-072-1151 645-072-6552 645-072-6552 * E4600 部品名 Barcode (Part Code) *636-087-1410* *636-087-1649* *645-054-4163* *645-057-4726* *645-064-7970* *645-070-8398* *645-072-1151* *645-072-6552* Part Name ｽﾍﾟｰｻｰ SPACER ｽﾍﾟｰｻｰ （LCD ﾜｲﾔ） SPACER (LCD WIRE) USBｿｹｯﾄ USB SOCKET ﾊﾟﾂﾄﾞ (L=4) PAD (L=4) ｶｰﾄﾞﾌ
Parts List Part Number Part Code A1-00157 A1-00157 A2-07028 A2-07028 A2-07034 A2-07034 A3-07496 A3-07496 A3A07504 A3A07504 A3A07578 A3A07578 A3A07580 A3A07580 A3A07581 A3A07581 A4-40432 A4-40432 A4-40433 A4-40433 A4-40434 A4-40434 A4-40435 A4-40435 A4-40437 A4-40437 A4-40450 A4-40450 A4-40455 A4-40455 A4-40456 A4-40456 A4-40457 A4-40457 E4600 部品名 Barcode (Part Code) *A1-00157* *A2-07028* *A2-07034* *A3-07496* *A3A07504* *A3A07578* *A3A07580* *A3A07581* *A4-40432* *A4-40433* *A4-40434* *A4-40435* *A4-4043
Parts List Part Number Part Code A4-40458 A4-40458 A4-40515 A4-40515 A4-40581 A4-40581 A4-40624 A4-40624 A4-40718 A4-40718 A4-40833 A4-40833 A4-40922 A4-40922 A4A41149 A4A41149 A4Z25502 * A4Z25502 A4Z25596 * A4Z25596 A4Z25805 * A4Z25805 AKE-1524 AKE-1524 E4600 部品名 Barcode (Part Code) *A4-40458* *A4-40515* *A4-40581* *A4-40624* *A4-40718* *A4-40833* *A4-40922* *A4A41149* *A4Z25502* *A4Z25596* *A4Z25805* *AKE-1524* Part Name ｷﾞﾔ軸B GEAR SHAFT B ｷﾞﾔ軸D GEAR SHAFT D ﾊﾞﾘｱﾘﾝｸﾞﾊﾞﾈ BARRIER RING SPRING FPC固定ﾃｰﾌﾟ F
