Handleiding

88
Pl
Ru
Nl
Se
It
De
Dk
Hu
Cz
Fi
No
Ro
Pomiar
Uwaga — korzystanie z elementów sterowania
lub regulacji, czy też wykonywanie procedur w
sposób inny, niż określony w niniejszym
podręczniku, może spowodować narażenie na
niebezpieczne promieniowanie.
1. Włóż baterię do komory baterii. (Patrz
„Wkładanie i wymiana baterii”)
2. Regulacja dioptrii
Przeprowadź regulację dioptrii, aby uzyskać
wyraźny obraz na ekranie LCD.
Najpierw obróć do końca pierścień regulacji dioptrii
w kierunku przeciwnym do ruchu wskazówek
zegara. Następnie włącz zasilanie, aby aktywować
ekran LCD podczas spoglądania przez dalmierz
laserowy Nikon. Obróć pierścień regulacji dioptrii w
prawo, do momentu gdy obraz będzie ostry.
Jeśli regulacja dioptrii nie zostanie
przeprowadzona, właściwe ustawienie celu na
obiekcie może nie być możliwe.
3. Pomiar
Przed rozpoczęciem pomiaru sprawdź ustawienia
urządzenia.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.



Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.



Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.



Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.



Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.



Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.



Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.



Natychmiast po
włączeniu. (Inicjalizacja)
Tryb czuwania. Ustawianie na celu.
3. Naciśnij raz przycisk
POWER ON/Measurement (Włączenie
zasilania/pomiar), aby rozpocząć pojedynczy pomiar.
Wciśnięcie przycisku umożliwi wykonanie ciągłego pomiaru przez
około 20 sekund.
Pomiar.
4. Podczas pomiaru wewnętrzny ekran wyświetla na przemian wskazanie
„odległość” i „błąd pomiaru”. (Oznaczenie promienia lasera miga.)
Pomiar zakończony
niepowodzeniem
lub brak możliwości
dokonania pomiaru.
Wyświetlanie
pomierzonej
wartości. (Cel 1)
Wyświetlanie
pomierzonej
wartości. (Cel 2)
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.



5. Po dokonaniu pomiaru przez około 8 sekund wyświetlane są
wyniki, a następnie zasilanie jest wyłączane. Po n
aciśnięciu POWER
ON/Measurement button
(Włączenie zasilania/pomiar) podczas
włączonego zasilania (gdy wewnętrzny wyświetlacz jest aktywny)
rozpoczyna się kolejny pomiar pojedynczy.
1. Włącz zasilanie (upewnij się, że
wewnętrzny ekran jest włączony)
2. Skieruj na cel.
Ustaw cel na środku
krzyża nitek.
(Automatyczne wyłączanie zasilania
po upływie 8 sekund nieużytkowania)