Owner's Manual
Table Of Contents
- Using the Supplied Manuals
- Quick Start Guide
- Owners Manual
- Two-Button Reset
- Set Language / Time
- Table of Contents
- Q & A Index
- Supplied Accessories
- Parts & Controls
- Getting Started
- Basic Photography & Playback
- Focus
- Image Size & Quality
- Release Mode
- Using the Built-In Flash
- ISO Sensitivity
- P, S, A, and M Modes
- Exposure
- White Balance
- Picture Controls
- Active D-Lighting
- Multiple Exposure
- Using an Optional GPS Unit
- More Playback Options
- Connecting to Other Devices
- Menu Guide
- Compatible Lenses
- Optional Flash Units
- Other Accessories
- Care / Maintenance
- Troubleshooting
- Error Messages
- Defaults
- Memory Card Capacity
- Specs
- Index
- Corrections to Manual
- Software Installation Instructions
- Scan of Software CD-ROM
- AC Power Cord Specs
- Warranty
D
Flash
Ultrl
for
built-in
flash
•
Commander
mod,
Mode
Camp
1ilJ·
~
011
~
011
~
o
CH
c)5,t
~OK
,
'(
Built-in
flash
LW
Grou~
A
•
Group
B
Channel
OMove
II
Commander
Mode
Use
the
built-in flash
as
a master flash controlling one or more remote optional
58-900, 58-800, 58-600, or 58-R200 flash units in up
to
two
groups
(A
and
8)
using
advanced wireless lighting.
Selecting this
option
displays
the
menu shown at right.
Press
....
or
~
to
highlight
the following options, •
or.
to
change.
Option
Description
Built-in
flash
Choose a flash mode for the built-in flash (commander flash).
AA
M
Channel
Group B
TTL
M
i-TTL
mode. Choose flash compensation from values between +3.0 and -3.0
EV
in
increments
of
'
13
EV.
Choose the flash
leve/hom
values between
Fl.Ill
and
1/128
('1128offull power).
I Thebuilt-in flash does
notfire,but
the AF-assist illuminator lights. The built-in flash
!rTl~~~?~
rais~?~?~~at
it
can
emit
monitor
pre-flashes.
Group A! Choose a flash mode for all flash units in group
A.
TTL
i-TTL
mode. Choose flash compensation from values between +3.0 and -3.0
EV
in
increments
of
'
13
EV.
Auto aperture (available onlywlthSB-900
andSB~8b6flash
units). Chooseflash
compensation from values between +3.0 and -3.0
EV
in increments
of'/3
EV.
Choose the flash level from values between Full and
1/128
('
1128
of
full power).
'The flash units in this group
do
not
fire.
Choose
aflashmodeforalfflashunits
in
groupB:"fhe
options availabfe
are
the
same
as
those listed for Group
A,
above.
Choose from channels 1-4. All flash units in both groups must be set
to
the same
channel.
Follow
the
steps below
to
take photographs in commander mode.
Comp
0;:
~
~
Mode
IiII
011
lDJ
o
CH
C)S,t
:OiJOK
CI
Flash
(ntrl
for
bUIIl·in
flash
•
Commander
mode
,
Y
Builhn
flash
c·.
Group
A
1I
Group
B
Channel
E3Move
1 Adjust settings for
the
built-in flash.
Choose the flash control mode and
output
level for the
built-in flash. Note
that
output
level
can
not
be adjusted in
--
mode.
188