Motorized Roller Shade User’s Manual Model：MRS-32A / MRS-32B / MRS-32C
Safety Precautions Thank you for your purchase. Please review the instructions carefully before using the product, and save these instructions for future consultation. ⚫ WARNING! Important safety instruction: It is critical for your safety and the safety of those around you to follow these instructions. Save these instructions. ⚫ WARNING! The drive shall be disconnected from its power source during cleaning, maintenance and when replacing parts.
Shade & Accessories _ AC Power Normal Size 36W Adapter x 1 Power Cable x 1 Extension cord x 1 (Optional) Large Size 65W Adapter x 1 Remote (Optional) RC-A01 Power Cord x 1 Extension cord x 1 (Optional)
Shade & Accessories _Battery Power Charger PB-01S (Optional) Remote (Optional) RC-A01 Power Charger PB-02 (Optional)
Shade & Accessories _Battery 36W Adapter x 1 (Optional) Remote (Optional) RC-A01 Charge Cable x 1 (Optional) Extension cord x 1 (Optional)
Setup & Operation Battery-powered shade Charging Port Button LED Indicator LED Indicator Button Charge cable
Setup & Operation AC-powered shade Button & LED Indicator
Setup & Operation Power ON / OFF Power ON Hold the shade button for 3 seconds and the green light will flash. Power OFF Hold the shade button for 3 seconds and the red light will flash. Pair shades with a Remote The shades are already paired with the Remote Control, If needed, please follow the steps to reassign the shades to another group. IMPOTANT! Please pair only one type of shades in the same group. 捲簾 按鍵 When powered on, press the Hold SET for 3 seconds to enter Choose a desired group.
Setup & Operation Un-pair the shade from Remote control 捲簾 圖示 捲簾 按鍵 Hold any Group button, the Press the button 3 times to shades assigned to the group enter Pairing mode. The will move up and down. green light will start flashing. Hold SET to enter Setup mode. The Group LEDs will start blinking. 捲簾 圖示 Choose a desired group. The shade will move up and Hold SET for 3 seconds to leave The selected group number down 2 times to indicate Setup mode. The Group LEDs will will blink.
Setup & Operation IMPORTANT! Please setup the positions of a single shade to avoid tampering with the positions of other shades assigned to the same group: 1. Pair the desired shade to any new group alone, then setup the positions via new group, or 2. Power off the other shades in the same group, and setup the positions of the desired shade. IMPORTANT! Top and Bottom positions must be setup for full function of the shades.
Setup & Operation Setup Bottom Position 捲簾 圖示 柔紗簾 圖示 捲簾 圖示 Move the shade to a desired Bottom position by Remote. Hold RESET for 1 second. ※ For PerfectSheer, please move to vane fully opened position. The Group LEDs will start blinking. 捲簾 圖示 Choose the desired group. Press CLOSE to setup the The shade will move up and Bottom position. down to indicate successful setup.
Setup & Operation (※Perfect Sheer only) IMPORTANT! Top, Bottom and Vane Open positions must be setup for full function of the Perfect Sheer shades. Setup Vane Open Position 柔紗簾 圖示 柔紗簾 圖示 Move the shade to the Hold RESET for 1 second. The lowest position of the shade Group LEDs will start blinking. by Remote. 柔紗簾 圖示 Press SET to setup the The shade will move up and Vane Open position. down to indicate successful setup. Choose the desired group.
Setup & Operation IMPORTANT! All position must be setup before My Favorite setup can begin. IMPORTANT! Clearing any of the positions will disable My Favorite feature. Setup / Clear My Favorite 捲簾 圖示 捲簾 圖示 Move the shade to a desired Hold SET for 3 second. The Favorite position by Remote. Group LEDs will start blinking. 捲簾 圖示 Press ★ to setup My The shade will move up and Favorite. down to indicate successful Hold ★ for 1 second to setup.
Setup & Operation IMPORTANT! Please clear the positions of a single shade to avoid tampering with the limits of other shades assigned to the same group: 1. Pair the desired shade to any new group alone, and clear the positions via new group, or 2. Power off the other shades in the same group, and clear the positions of the desired shade. IMPORTANT! Top and Bottom positions must be setup for full function of the shades.
Setup & Operation Remote control ^ / v： Adjust shade position / Adjust Light Filtering OPEN：Shade goes up continually CLOSE： Shade goes down continually ■ ：Stop the shade 山(圖)：Move to Best View 房(圖)： Move to Best Privacy ★ ：Move to My Favorite Press Group(1-5, ALL) ：Select a group Hold Group(1-5, ALL)：Identify the shades in the group For more Remote model, please visit: (網址) Button control Press the button to move the shade in first direction when the shade is still.
Setup & Operation Calibration STEP 1. Press the shade button 8 times to enter Setup mode (green light illuminates). STEP 2. In Setup mode, press the button 2 times (green light blinks). STEP 3. The shade will execute calibration. Note: Please make sure the shade route is clear and do NOT operate the shade during calibration. Clear All Positions STEP 1. Press the shade button 8 times to enter Setup mode (green light illuminates). STEP 2. In Setup mode, press the button 4 times (green light blinks). STEP 3.
Troubleshooting Problems Possible Cause Description Operate the shade by a Remote and check the LED indicator on the shade. Green light blinks：The shade receives signal normally. No Signal Red light blinks：Low battery / Over temperature limit Red/Green light blinks：Other problems No light：Not receiving signal / Not paired with a Remote / The shade is powered OFF.
Troubleshooting Problems Possible Cause Description Press ^/ v on Remote to operate the shade and check if the shade LED blinks green and the shade works normally. If not, the shade positions might not be fully set up for full functionality, please refer to Section “Setup & The Positions are not fully setup. Operation” to Setup positions. IMPORTANT! Top and Bottom positions must be setup for full function of the shades.
Specification NO. 1 2 Item Specification Battery-powered：Li-ion batteries x3 Power Source AC power：100-240V, 50 / 60Hz Battery operating 4.2V~3.4V (Single cell) voltage range 3 Radio type 2.
Safety Statement Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety Statement RED Compliance Statement (Delete?) Hereby, Nien Made Enterprise Co., Ltd. declares that the radio equipment type MRS is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.nienmade.com/ContactUs.aspx (TBD) This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment.
Safety Instructions for Lithium batteries The product may contain lithium-ion batteries; the battery contains flammable materials, such as organic solvents. Mishandling of the battery may cause fire, smoke, or explosion. DANGER Do not immerse the battery in any liquid, such as water, beverages, or other fluids. Exposure to liquid may damage the battery or the battery pack. Damaging the battery may generate heat, smoke, catch fire, or explode.
Safety Instructions for Lithium batteries Do not directly solder to the battery. Soldering directly to the battery could melt the separator, damage the fume release vent or other safety mechanisms. This may cause the battery to generate heat, smoke, catch fire, or explode. Do not disassemble the battery. Disassembly or modification of the battery may damage the protection circuit. This may cause the battery to generate heat, smoke, catch fire, or explode. Do not charge the battery near high temperature.
Safety Instructions for Lithium batteries CAUTION Exposure to Direct Sunlight Do not use or leave the battery in a location exposed to excessive heat, such as in direct sunlight or in a car. Doing so could cause the battery to generate heat, smoke, catch fire, or explode. It may also cause the battery’s performance and life to deteriorate. Use with other Equipment or Power The battery pack has a protection circuit. Do not use the battery with other equipment or power as it may damage the protection circuit.
