Installation Guide

NICOR, Inc. 2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F: 800.892.8393
DSE Surface Mount LED Downlight
INSTALLATION INSTRUCTIONS
Model(s): DSE4SQ, DSE5RD, DSE6SQ, DSE8RD, DSE9SQ, DSE9RD
WARNING:
•Risk of electric shock. Disconnect power at fuse or circuit breaker before installing or servicing.
•To prevent early lamp failure, lamp should only be installed in operating environments between -20°C and + 40°C (104°F and -4°F)
•No user serviceable parts inside. To avoid electric shock do not disassemble product.
•This product is not intended for use in emergency light xtures or exit signs.
ATTENTION:
Turn power o before inspection, installation, or removal.
Suitable for use in wet locations. Use only on 120VAC, 60Hz circuits.
What’s In The Box
One (1) DSE Two (2) Mounting Screws
One (1) Bracket
Tools Needed
This DSE Series requires very few tools for installation. A
screwdriver and a pair of wirecutters will help to install the
product to a JBox.
Three (3) Wire Nuts
PATENT PENDING NICOR, Inc. 2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F: 800.892.8393 www.nicorlighting.com Altair 1 February 1. 2018 4:42 PM rev 1.4
Altair - LSA
INSTALLATION INSTRUCTIONS
The installation must only be performed by a licensed electrician.
To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or
Canadian Electrical Code (CSA 22.1) in Canada.
Disconnect power before installing the product or servicing it.
Wait until xture has cooled down before installing or servicing the xture.
Suitable for Continuous Row Mountings, 10 Fixtures Maximum.
Maximum Ambient Temperature Rating 40°C
MIN. 60°C SUPPLY CONDUCTORS
What’s In The Box Tools & Materials Needed
A screwdriver, drill, ⁄” hex driver, wire cutters, and appropriate hardware will be
needed to install the LSA.
One (1) Altair
Aircraft Cable
LSA Aircraft Cable Kit Non Power Feed, 150” Length - LSA-1-CABLE
One (1) Drop Ceiling
Bracket
One (1) Cable Coupler One (1) 150”
Aircraft Cables
One (1) Grip Lock One (1) 2” Canopy
One (1) Crossbars One (1) Cable Coupler One (1) 150”
Aircraft Cables
One (1) Grip Lock One (1) 5” Power
Feed Canopy
Two (2) Wire Ties Two (2) Cable
Bushing
One (1) 160”
Power Feed Cable
LSA Aircraft Cable Kit Power Feed, 150” Length - LSA-1-CABLE-PF
Pendant Mount
LSA, LSQ, LSE Pendant Mount Non Power Feed, 48” Length - LSALSELSQ-1-PENDANT
One (1) Crossbar One (1)
48” Pendant Stem
One (1) Swivel Ball
w/ Lock Screw
One (1) Canopy
One (1) Crossbar One (1)
48” Pendant Stem
One (1) Swivel Ball
w/ Lock Screw
One (1) Canopy
LSA, LSQ, LSE Pendant Mount Power Feed, 48” Length - LSALSELSQ-1-PENDANT-PF
Stem
Adjusting Kit
REVISIONS
REV. DESCRIPTION DATE INITIALS
PROPRIETARY AND CONFIDENTIAL
2200 Midtown Pl NE Albuquerque, NM 87107
Office: 800.821.6283 - Fax: [phone]
NICOR,Inc.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
NICOR LIGHTING. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
NICOR LIGHTING IS PROHIBITED.
SPECIFY
NC
DO NOT SCALE DRAWING
1-8 ALLEN
SHEET 1 OF 2
6/20/2017 JORGE
UNLESS OTHERWISE SPECIFIED:
SCALE: 2:1
WEIGHT:
REV
DWG. NO.
A
SIZE
TITLE:
NAME DATE
DRAWN
POWDER COAT
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH 1
TWO PLACE DECIMAL .03
THREE PLACE DECIMAL .001
One (1) 60” Power
Feed Cable
Stem
Adjusting Kit
REVISIONS
REV. DESCRIPTION DATE INITIALS
PROPRIETARY AND CONFIDENTIAL
2200 Midtown Pl NE Albuquerque, NM 87107
Office: 800.821.6283 - Fax: [phone]
NICOR,Inc.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
NICOR LIGHTING. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
NICOR LIGHTING IS PROHIBITED.
SPECIFY
NC
DO NOT SCALE DRAWING
1-8 ALLEN
SHEET 1 OF 2
6/20/2017 JORGE
UNLESS OTHERWISE SPECIFIED:
SCALE: 2:1
WEIGHT:
REV
DWG. NO.
A
SIZE
TITLE:
NAME DATE
DRAWN
POWDER COAT
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH 1
TWO PLACE DECIMAL .03
THREE PLACE DECIMAL .001
Surface Mounting
LSA Surface Mount Power Feed Kit - LSA-1-SURFACE-PF
One (1) Continuous
Run Clip
Four (4) screws
and anchors
Continuous Run
LSA Continuous Run Spring Clip - LSA-1-CR-CLIP
A A
B B
C C
D D
E E
F F
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:2 SHEET 1 OF 1
A4
WEIGHT:
LS NICOR AC
A A
B B
C C
D D
E E
F F
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:2 SHEET 1 OF 1
A4
WEIGHT:
LS NICOR AC
A A
B B
C C
D D
E E
F F
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:2 SHEET 1 OF 1
A4
WEIGHT:
LS NICOR AC
Three (3) surface
mount brackets
Six (6) screws and anchors
(surface mount only)
One (1) Push-In
Connector
One (1) 24”
Power Feed Cable
One (1) Endcap
w/Knockout
Endcap w/Knockout
LSA Endcap W/Knockout & EVA - LSA-1-ENDCAPKIT
REVISIONS
REV. DESCRIPTION DATE INITIALS
PROPRIETARY AND CONFIDENTIAL
2200 Midtown Pl NE Albuquerque, NM 87107
Office: 800.821.6283 - Fax: [phone]
NICOR,Inc.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
NICOR LIGHTING. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
NICOR LIGHTING IS PROHIBITED.
SPECIFY
NC
DO NOT SCALE DRAWING
DROP CEILING BRACKET
SHEET 1 OF 2
6/20/2017 JORGE
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:1
WEIGHT:
REV
DWG. NO.
A
SIZE
TITLE:
NAME DATE
DRAWN
POWDER COAT
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH 1
TWO PLACE DECIMAL .03
THREE PLACE DECIMAL .001
REVISIONS
REV. DESCRIPTION DATE INITIALS
PROPRIETARY AND CONFIDENTIAL
2200 Midtown Pl NE Albuquerque, NM 87107
Office: 800.821.6283 - Fax: [phone]
NICOR,Inc.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
NICOR LIGHTING. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
NICOR LIGHTING IS PROHIBITED.
SPECIFY
NC
DO NOT SCALE DRAWING
COUPLER
SHEET 1 OF 2
6/20/2017 JORGE
UNLESS OTHERWISE SPECIFIED:
SCALE: 2:1
WEIGHT:
REV
DWG. NO.
A
SIZE
TITLE:
NAME DATE
DRAWN
POWDER COAT
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH 1
TWO PLACE DECIMAL .03
THREE PLACE DECIMAL .001
One (1) Cable
Bushing
1
Make wire connections as shown.
2
Carefully tuck the wires into the J-Box, align the spring clips on the xture to
the bracket holes and push the xture ush to the ceiling, snapping the clips
into the bracket.
3
Mount the bracket to the existing J-Box with the 2
mounting screws; if installing a square DSE xture, the
mounting bracket should be aligned to the J-Box to
ensure the square is in the desired direction.
JBOX
LINE
Black (line)
Ground
White (neutral)
Black (line)
Green (ground)
White (neutral)
DSE
Standard 4” J-Box Installation