Datasheet

LV series
Specifications
Temperature Characteristics
(Max.Impedance Ratio)
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Tangent of loss angle (tan δ)
ESR
(1)
Leakage Current ( 2)
Performance CharacteristicsItem
–
55 to +105°C
16 to 100V
6.8 to 470µF
±20% at 120Hz, 20°C
Less than or equal to the specified value
at
120Hz, 20°C
Less than or equal to the specified value
at
100kHz, 20°C
Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Z+105°C / Z+20°C 1.25 (100kHz)
Z–55°C / Z+20°C 1.25
Endurance
Damp Heat
(Steady State)
Resistance to
Soldering Heat
Marking
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours at 105°C.
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
Navy blue print on the case top
Capacitance change
tan δ
Leakage current ( 2)
ESR
(1)
Within ± 20% of the initial capacitance value
(
3
)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
Leakage current ( 2)
ESR
(1)
Within ± 20% of the initial capacitance value
(
3
)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
Leakage current ( 2)
ESR
(1)
Within ± 10% of the initial capacitance value
(
3
)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
High voltage (to 100V), Low ESR, High ripple current.
Long life of 3000 hours at 105°C.
Radial lead type:
Lead free flow soldering condition correspondence.
Compliant to the RoHS directive (2002/95/EC).
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
P
1
L
2
V
3
1
4
V
5
8
6
2
7
0
8
M
91011
Capacitance tolerance (±20%)
Rated capacitance (82
µF)
Rated voltage (35V)
D L
12
1
Size code
Series name
Type
Configuration
L
+0.5MAX.
15MIN
4MIN
φD
+0.5 MAX.
Resin coated Case
Tinned lead Wire
φd
LV 82 V 012
Capacitance
Series
Lot. No.
Voltage(V:35V)
P
±0.5
Dimensions
Type numbering system (Example : 35V 82
µ
F)
Radial Lead Type, Long Life Assurance
Dimension table in next page.
Voltage
V 16202535506380100
Code C D E V H J K 2A
Size
φD
L
P
φd
φ10
×
13L
10.0
12.5
5.0
0.6
φ8
×
9L
8.0
8.5
3.5
0.6
φ8
×
12L
8.0
11.5
3.5
0.6
(mm)
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LV
LF
High Voltage Long Life
Please refer to page 20 about the end seal configulation.
High Temperature
LX
CAT.8100A