Buying Guide

12
NIBCO INC. WORLD HEADQUARTERS • 1516 MIDDLEBURY ST. • ELKHART, IN 46516-4740 • USA • PH: 1.800.234.0227
TECH SERVICES PH: 1.888.446.4226 • FAX: [phone] • INTERNATIONAL OFFICE PH: +1.574.295.3327 • FAX: [phone]
www.nibco.com
Visit our website for the most current information.
www.nibco.com
AHEAD OF THE FLOW
®
Dezincification
Resistant
Bronze Ball Valves
Two-Piece Body • Full Port • Stainless Trim • Blowout-Proof Stem • Vented Ball
600 PSI/41.4 bar non-shock cold working pressure
150 PSI/10.3 bar saturated steam
t
CONFORMS TO MSS SP-110
T-585-70-66
Threaded
S-585-70-66
Solder
MATERIAL LIST
PART SPECIFICATION
1. Handle Nut Stainless Steel 300 Series
2. Handle Zinc Plated Steel Clear Chromate
Plastisol Coated
3. Threaded Pack Gland Brass ASTM B 16 Alloy C36000
4. Packing PTFE
5. Stem Stainless Steel ASTM A 276 Type 316
6. Thrust Washer Reinforced PTFE
7. Ball (Vented) Stainless Steel ASTM A 276 Type 316
or ASTM A 351 Type CF8M
8. Seat Ring (2) Reinforced PTFE
9. Body Bronze ASTM B 584 Alloy C84400
10. Body End Piece Bronze ASTM B 584 Alloy C84400
¼" size only has a 304 stainless steel grounding washer.
S-585-70-66
C x C
T-585-70-66
NPT x NPT
B
A
C
D
DIMENSIONS—WEIGHTS—QUANTITIES
Dimensions
T-585-70-66 S-585-70-66 T-585-70-66 S-585-70-66
Size A A B C C D T-585-70-66 S-585-70-66 Master
In. mm. In. mm. In. mm. In. mm. In. mm. In. mm. In. mm. Lbs. Kg. Lbs. Kg. Ctn. Qty.
¼ 8 2.00 51 1.75 44 1.75 44 5.00 127 4.75 121 .38 10 .45 .21 .42 .19 100
⅜ 10 2.00 51 1.84 47 1.75 44 5.00 127 4.81 122 .38 10 .45 .21 .42 .19 100
½ 15 2.44 62 2.56 65 1.88 48 5.19 132 5.25 133 .50 13 .64 .29 .60 .27 100
¾ 20 2.94 75 3.25 82 2.25 57 6.25 159 6.25 159 .75 19 1.33 .60 1.27 .58 50
1 25 3.34 85 3.75 95 2.38 60 6.44 164 6.63 168 1.00 25 1.79 .81 1.72 .78 40
1 ¼ 32 4.19 106 5.06 128 3.00 76 6.75 171 7.19 183 1.25 32 3.34 1.52 3.40 1.55 20
1 ½ 40 4.72 120 5.99 151 3.16 80 9.06 230 9.69 246 1.50 38 4.84 2.20 5.18 2.35 10
2 50 5.16 131 6.72 170 3.50 89 9.25 235 10.06 256 2.00 51 7.41 3.37 7.83 3.56 8
Note: solder end is designed to be soft-soldered into lines using solders with the melting point not exceeding 500°F.
Higher temperature solders will damage the seat material. See installation sheet packaged with valves.
t
For detailed operating pressure, refer to pressure temperature chart on page 41.
Revised 7/19/2018
*Weighted average lead content ≤ 0.25%
LEAD FREE*
OPTION
AVAILABLE
OXYGEN
SERVICE
OPTION
AVAILABLE
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.