Buying Guide

9
NIBCO INC. WORLD HEADQUARTERS • 1516 MIDDLEBURY ST. • ELKHART, IN 46516-4740 • USA • PH: 1.800.234.0227
TECH SERVICES PH: 1.888.446.4226 • FAX: [phone] • INTERNATIONAL OFFICE PH: +1.574.295.3327 • FAX: [phone]
www.nibco.com
Visit our website for the most current information.
www.nibco.com
AHEAD OF THE FLOW
®
Dezincification
Resistant
Bronze Ball Valves
Two-Piece Body • Full Port ¼"-1" • Conventional Port 1¼"-3" •
Bronze Trim • Blowout-Proof Stem
600 PSI/41.4 bar non-shock cold working pressure
150 PSI/10.3 bar saturated steam
t
CONFORMS TO MSS SP-110
T-580-70
Threaded
MATERIAL LIST
PART SPECIFICATION
1. Handle Nut Zinc Plated Steel
2. Handle Zinc Plated Steel Clear Chromate
Plastisol Coated
3. Threaded Pack Gland Brass ASTM B 16 Alloy C36000
4. Packing PTFE
5. Stem Silicon Bronze ASTM B 371 Alloy C69430
or ASTM B 99 Alloy C65100
6. Thrust Washer Reinforced PTFE
7. Ball Brass ASTM B 124 Alloy C37700 or ASTM B16
Alloy C36000 EACH with Hard Chrome Plate
8. Seat Ring (2) Reinforced PTFE
9. Body Cast Red Bronze ASTM B 584 Alloy C84400
10. Body End Piece Cast Red Bronze ASTM B 584 Alloy C84400
¼" size only has a 304 stainless steel grounding washer.
DIMENSIONS—WEIGHTS—QUANTITIES
Dimensions
T-580-70 S-580-70 T-580-70 S-580-70
Size A A B C C D T-580-70 S-580-70 Master
In. mm. In. mm. In. mm. In. mm. In. mm. In. mm. In. mm. Lbs. Kg. Lbs. Kg. Ctn. Qty.
† ¼ 8 2.00 51 1.75 44 1.75 44 5.00 127 4.75 121 .38 10 .45 .21 .42 .19 100
† ⅜ 10 2.00 51 1.84 47 1.75 44 5.00 127 4.81 122 .38 10 .45 .21 .42 .19 100
† ½ 15 2.44 62 2.56 65 1.88 48 5.19 132 5.25 133 .50 13 .64 .29 .60 .27 100
† ¾ 20 2.94 75 3.25 83 2.25 57 6.25 159 6.25 159 .75 19 1.33 .60 1.27 .58 50
†1 25 3.34 85 3.75 95 2.38 60 6.44 164 6.63 168 1.00 25 1.79 .81 1.72 .78 40
1 ¼ 32 3.94 100 4.00 102 2.63 67 6.75 171 6.75 171 1.00 25 2.17 .98 1.78 .81 20
1 ½ 40 4.31 109 4.44 113 3.00 76 8.88 226 9.00 229 1.25 32 3.27 1.48 2.87 1.30 20
2 50 4.63 118 5.50 140 3.16 80 9.06 230 9.50 241 1.50 38 5.09 2.31 4.60 2.08 10
2 ½ 65 5.84 148 7.28 185 3.50 89 9.66 245 10.38 264 2.00 51 8.25 3.74 8.18 3.71 6
3 80 7.09 180 8.78 223 4.41 112 11.53 293 12.38 314 2.50 64 15.65 7.10 14.86 6.74 4
† NIBCO supplies full port T or S-585-70 on this size.
Note: solder end is designed to be soft-soldered into lines using solders with the melting point not exceeding 500°F.
Higher temperature solders will damage the seat material. See installation sheet packaged with valves.
S-580-70
Solder
T-580-70
NPT x NPT
S-580-70
C x C
B
A
C
D
LEAD FREE*
OPTION
AVAILABLE
t
For detailed operating pressure, refer to pressure temperature chart on page 41.
Revised 7/19/2018
*Weighted average lead content ≤ 0.25%
OXYGEN
SERVICE
OPTION
AVAILABLE
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.