Quick Start Guide

10) On the Video tab, set video Input to Composite.
11) Click the Audio tab and set audio Input to Unbalanced.
Click Save Sengs.
12) To enable streaming, ensure the Enable Streaming box
is selected. Enter the proper address for the server
in the Desnaon IP eld and the port number in the
Port eld.
13) Click Save Sengs. Click OK aer the operaon is
successful.
14) Your streaming content is now available through your
server. To stream a live video, a CDN account is required.
4. First start setup continued
Quick Start Guide
Niagara
®
2200
Contact ViewCast Technical Support at [e-mail].
40-03330-01-A
© 2012 ViewCast Corporation. ViewCast
®
, Niagara
®
(and design)
TM
are registered trademarks of ViewCast Corporation
or its subsidiaries. All other trademarks are the property of their respective owners. Product specications and availability
may change without notice.
A: Power Buon and Indicator Light
• Press this buon once to start the Niagara 2200.
• Press this buon once to turn o the Niagara 2200 when it is on.
• Press and hold for 5 seconds to execute an immediate power o.
NOTE: Do NOT aempt to encode while light connues blinking.
B: Reset Buon
• Resets the Niagara 2200.
• Use a pointed device to insert in the hole and press the reset buon.
• This buon has three dierent opons:
1. Press and release aer the rst set of 10 LEDs start to light
(approximately 1 to 3 seconds) to reboot the Niagara 2200.
NOTE: The lights on the volume indicator will illuminate in one-second intervals.
2. Press and release aer the second set of 10 LEDs start to light
(approximately 4 to 6 seconds) to keep all set proles and restore
the Niagara 2200 operang system.
NOTE: The lights on the volume indicator will illuminate in one-second
intervals, but do NOT progress all the way to the far right.
Warning! Opon 3 deletes all previously set proles.
3. Press and hold for approximately 10 seconds unl all 20 LEDs
remain lit to restore the Niagara 2200 to complete factory defaults.
C: Stream Buon and Indicator Light
• Iniates streaming of all proles assigned to the buon.
D: Stop Buon
• Stops the encoder streaming acvity when you press this buon once.
E: USB Port
• Allows the export of les to USB storage devices, installing updates
or rmware, or connecng USB devices.
F: Audio Lever Meters (Acvity Feedback)
• Audio feedback meters.
• Shows incoming le and right audio channel input.
G: Stereo Headphone Connecon
• The headphone output connecon is for audio monitoring.
H: Volume Buon (Up/Down)
• Audio level headphone control.
• This control changes the volume on the headset output only.
I: Alarm/Status Indicator
• Indicator light remains solid when an applicaon alert has occurred.
J: Remote Control
• Indicator light remains solid when another user is accessing the
Niagara 2200 across the network from a computer.
K: Video Condence Indicator
• Video encoding status (acve). The indicator will stay lit (blue) only
while streaming. If the video input is lost it will not be lit.
Use the front panel picture to familiarize yourself with the controls of the
Niagara 2200.
The Niagara 2200 Front Panel
A: Power Buon
and Indicator Light
J: Remote Control
K: Video Condence Indicator
I: Alarm/Status Indicator
C: Stream Buon
and Indicator Light
F: Audio Level Meters
(Acvity Feedback)
H: Volume Buon
(Up/Down)
G: Headphone Connecon
D: Stop Buon
E: USB Port
B: Reset Buon
NOTE: You may also use the front panel Streaming
buon to start streaming.
NOTE: You can easily test this streaming prole
from the Encoders window by clicking the blue circle
Streaming buon on the right side of the encoder. The
buon changes from a red circle to a blue circle when
you start streaming. The status changes from Stopped
to Encoding Live.
US / Canada [phone]
|
Europe / Middle East / Africa [phone]
|
Asia / Pacic [phone]