Installation Instructions

ManualsBrandsNEXXT SOLUTIONS ManualsCamera & PhotoCamera

Thank you for using smart camera

Smart Life

4.APP Video Browsing Details

①Preview mode ②Monitor Switch

④SQ

③About device

⑤Full screen

Reset Button: Long press “reset” hole 5sec, reset success.

Basic Parameters

Component Description:

Product Name: Smart Camera

Pixel: 1.0Mp/2.0MP

Video Compression: H.264 High Proﬁle

Image Enhancement: Digital Wide Dynamic 3D Noise Reduction

Local Storage: MicroTF Card (64G Max)

Wireless Encryption: WEP/WPA/WPA2 Encryption

Power Input: 12V 1A(Min)

Total Power Consumption: 12W (Max)

WirelessStandard: 2.4G 802.11 b/g/n

Support Platform: Android/iOS

It is recommended to insert 8-64GB high-speed Micro TF card, otherwise

it will not be able to store, view historical video and support Important

functions such as ﬁrmware upgrading.

2.Install APP

Download APP: scan the QR code below to download and install.

according to the prompts.

5.Matters Need Attention

Try to keep away from the metal space;

Avoid the furniture , microwave oven blocked;

Avoid the space where the audio, video and data lines are wound, and

keep the space away from them as large as possible;

Ensure that as close as possible to the coverage of wireless Wi-Fi

signals. Switching network environment;

In the new network environment, please press the reset hole about 5

seconds, then connect to the network.

The name and content of the harmful substances in the product

This product conforms to RoHS environmental protection requirements. At

present, there is no mature technology in the world to replace or reduce the

lead content in the electronic ceramics. porcelain, optical glass, steel and

copper alloy.

Part

Name

Harmful Substance

shell

Board

charger

annex

This form is based on the provisions of SJ/T 11364。

Cr(VI) PBB PBDE

○

○○○○

○

○○○○

○

○○○○

○

○○○○

Mobile:

Address:

Model: Camera ID:

Device store: Date of purchase:

Store address:

Store contact number:

Maintenance voucher of intelligent

Customer: Mobile:

Address:

Model: Camera ID:

Device store: Date of purchase:

Store address:

Store contact number:

Sig nal 9 9%

④

③

⑤

①

②

2018-05-14 11:20:30

Maintenance voucher of intelligent

Customer: Mobile:

Address:

Model: Camera ID:

Device store: Date of purchase:

Store address:

Store contact number:

Maintenance voucher of intelligent

Customer: Mobile:

Address:

Model: Camera ID:

Device store: Date of purchase:

Store address:

Store contact number:

01 02

·click "Conﬁrm". It will jump to the interface to prompt to scan the QR code

with camera and click "Continue" (Figure. 07);

·A QR code will prompt on your screen and you need to scan it with the

Smart Camera. (the camera is about 20-30 cm away from the mobile

phone lens). Then click "hear the prompt sound" (Figure. 08).

·"connecting" (Figure. 09);

07 08 09

3.1、 Add The Device-Scan QR code mode

·Make sure Wi-Fi is available and connected to the Internet.

·Open "Smart Life" APP, press the'+' in the upper right corner of the main

screen (Figure 01); choose “Security & Sensor”、click "Smart Camera"

(Figure 02) to add camera; and then click "Next step" (Figure 03);

·Connect the camera to the power, then system startup completed.

01 0302

3. 2、Add The Device- AP Mode

If you want to use AP Mode,press the reset button on the machine

·Make sure Wi-Fi is available and connected to the Internet.

·Connect the camera to the power, system startup completed.

·Open "Smart Life" APP, press the'+' in the upper right corner of the main

screen (Figure 13); choose “Security & Sensor”、click "Smart Camera"

(Figure 14) to add camera ; Alternatively, choose "other ways" to add (as

shown in Figure 15);

13 1514

·The interface jumps to the WALN connection interface, ﬁnds the Wi-Fi at the

beginning of "Smart Liﬁ", and clicks on the connection (Figure 22);

·When the connection is completed, click back and return to the APP interface,

at which time the APP display device is connected (Figure 23).

·At this time, the device has been successfully connected; the interface jumps

to "Add Device Successful" (Figure 24);

22 2423

·Then enter the password to complete the connection (Figure 19);

·Click Back and return to the APP compatible mode interface, where the Wi-Fi

name and the connected Wi-Fi name are displayed Password, click the

"Conﬁrm" button (Figure 20);

·The page jumps to where the interface prompts "Wi-ﬁ" to connect to the device

hotspot and clicks "Connect" (Figure 21)

20 2119

·If the mobile phone is not connected to wi-ﬁ, please click "Connect to

Wi-ﬁ" (Figure 04);

·It will jump to the WLAN interface and connects Wi-Fi (Figure 05).Please

note that only 2.4 GH Wi-Fi network is supported;

·If the phone is connected to Wi-Fi (Figure 06)；

04 05 06

·When the progress reaches 100%,connection completed(Figure 10), and

click "Finish";

·Then jump to preview interface (Figure 11)

·After closing the device preview interface, the interface returns to the APP

home page. At this time, the connected device will appear on the APP home

page (Figure 12). Then you can click directly to the device interface to see

the monitoring situation without re-adding afterwards.

10 12

·Then click "hot spot conﬁguration" (Figure 16;

·Then click” compatibility mode”, clicks"Next" (Figure 17);

·Then click "change Network" (Figure 18);

16 17 18

Note：Before using the "AP Mode",you need to switch to "AP Mode"

by lightly pressing the "Reset key" of the device.

Signa l 99 %

2018-05-14 11:20:30

·Then click “connected”, it will jump to the Preview Interface of the Device

(Figure 25)

·Close the device preview interface and the interface returns to the APP

home page, at which point the connected device will appear on the APP

home page.(Fig. 26), After entering the device interface to view, no need to

re-add, click directly into the device interface to view .

25 26

Signa l 99 %

2018-05-14 11:20:30

Federal Communications Commission (FCC) Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must acceptany interference received, including interference that

may cause undesired operation.

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in

a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

●Reorient or relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to

which the receiver is

connected.

●Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this device not expressly

approved by Xian Chishine Optoelectronics Technology Co.,Ltd may void

the FCC authorization to operate this device.

Note: The manufacturer is not responsible for any radio or TV interference

caused by unauthorized modifications to this equipment. Such modifications

could void the user’s authority to operate the equipment.

Radiation Exposure StatementThis equipment complies with FCC radiation

exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 20cm between

the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.