iR1200 Rugged Modem iR1200 GPS-Enabled Modem Administrator’s Guide General
Table of Contents Table of Contents Table of Figures................................................................................................1 FCC Compliance ..............................................................................................3 Required Components .....................................................................................5 How to Order..................................................................................................5 Online Documentation ..........
iR1200 Modem Circuit Switched Data ..............................................................................19 Installing iDEN Packet Data Applet..........................................................21 Hardware and Installation Requirements......................................................21 Before You Begin.........................................................................................22 Download Software Instructions ................................................................
Table of Contents Modem Configuration – Windows NT.........................................................44 Install the Modem.....................................................................................44 Configure the Modem Driver ...................................................................46 Create a Dial-up Networking Connection ................................................47 Modem Configuration – Windows 2000 ......................................................
iR1200 Modem Saving AT Settings....................................................................................62 GPS Default Parameters ...............................................................................63 AT Commands................................................................................................65 General AT Commands................................................................................65 User Image Profile Commands.................................................
Table of Contents Local Flow Control (PCCA).....................................................................75 Local Data Rate .......................................................................................76 Lock/Unlock the DCE...............................................................................77 Change the DCE’s PIN. ...........................................................................77 Packet Data Sleep Timer .................................................................
iR1200 Modem Troubleshooting..............................................................................................91 Common Problems .......................................................................................91 Error Messages.............................................................................................93 Diagnostic Commands .................................................................................94 Extended Error AT Command ........................................
Table of Contents IMPORTANT! Please Read Safety Notice on Page 99 before using the iR1200 Modem.
Table of Figures Table of Figures Table of Figures Page Figure 1 – iR1200 GPS-Enabled Modem 9 Figure 2 – Rear Panel of iR1200 Rugged Modem 11 Figure 3 – Rear Panel of iR1200 GPS-Enabled Modem 11 Figure 4 – Front Panel View of iR1200 Modem 15 Figure 5 – Cabling Diagram (Fixed Environment) 16 RFM-4002-5015 Rev 3 1
iR1200 Modem 2 nextel.
FCC Compliance FCC Compliance DECLARATION OF CONFORMITY Per FCC CFR 47 2.989 Responsible party name: Address: eLutions, Inc.
iR1200 Modem 4 nextel.
Required Components Required Components The following table lists components that have been approved for use with the iR1200 Rugged Modem and iR1200 GPS-Enabled modems. Part No.
iR1200 Modem Online Documentation The iR1200 modem is shipped with the following product documentation. Additional copies of these documents can be downloaded (at no charge) online at www.elutions.com/wireless or calling 1-888-349-4338. Part No. 6 Description RFM-4000-5015 Installation Guide RFM-4001-5015 Quick Reference Guide RFM-4003-5015 Warranty Card/Installation and Usage Requirements nextel.
Introduction Introduction Welcome to Nextel Thank you for purchasing the Nextel iR1200 modem. This modem works on the iDEN network. Once installed and configured, the iR1200 modem provides users with wireless data communications. This chapter includes: Using This Guide Page 7 Nextel Coverage Page 7 Nextel Customer Care Information Page 8 Using This Guide This guide provides instructions for installing the iR1200 Rugged Modem and the iR1200 GPS-Enabled Modem.
iR1200 Modem Nextel Customer Care For customer care issues including technical support contact Nextel Customer Care at 1-800-639-6111. When you call, please have a detailed description of your problem. To provide you with fast and quality support, our Customer Care representative may ask for information on the following: • Computer operating system (Windows 95/98/NT/2000/CE) • Version of the operating system (e.g. NT 4, Windows 95 Version B, CE 2.1, etc.
Overview Overview This chapter provides general details about the iR1200 modem. This chapter includes: General Overview Page 9 Modem Operating Modes Page 10 Modem Configurations Page 10 Modem Specifications Page 12 General Overview The iR1200 Modem is an iDEN data modem consisting of a modem card and an optional GPS (iR12000 GPS-Enabled Modem) receiver, contained in a rugged enclosure, to provide wireless data communications.
iR1200 Modem Modem Operating Modes The iR1200 provides the following data connection modes: • Packet Data: A wireless modem connection used for accessing the Internet, sending and receiving e-mail, and transferring small files over the packet data network using standard IP protocols. Data is sent in packets (blocks) at high speed. • Circuit Switched Data: A wireless modem connection for sending and receiving data (faxes, files, etc.
Overview Ignition Sense / Bypass Connector Modem Serial Data Connector 12VDC Power Connector Modem Antenna Connector Figure 2. Rear Panel of iR1200 Rugged Modem iR1200 GPS-Enabled Modem The following diagram displays components on the rear panel of the iR1200 GPS-Enabled Modem. GPS Serial Data Connector Modem Serial Data Connector GPS Antenna Connector Modem Antenna Connector Ignition Sense / Bypass Connector 12VDC Power Connector Figure 3.
iR1200 Modem Modem Specifications Transmission Modes Rugged metal enclosure Circuit-Switched, Packet Data & Hayes AT Commands Extruded Aluminum Status monitoring LED One bi-color LED for operating status External Modem Software User to utilize Windows drivers Internal Modem Software Micro controller firmware Radio Frequency Tx 806-821 MHz Rx 851-866 MHz TX Output Power 0.
Overview Vibration Shock Dust/Water Resistance per TIA/EIA 603 par 3.3.4 per MIL-STD-810E, method 516.4, procedure I Dust per MIL-STD-810E, method 510.3, procedure I Water per MIL-STD-810E, method 506.
iR1200 Modem 14 nextel.
Getting Started Getting Started This chapter describes how to connect your modem to a computer or mobile device in preparation for the configuration process. This chapter includes: Connecting the Modem Page 15 Communication Indicators Page 17 Connecting the Modem The following table describes how to connect the modem to the computer using the RS-232 cable. LED (signal indicators) displays the modem’s serial interface status. Status LED displays the modem’s iDEN network status.
iR1200 Modem COMPUTER 120VAC POWER SUPPLY GPS ANTENNA (OPTIONAL) MODEM ANTENNA RS-232 GPS DATA POWER IGNITION BYPASS PLUG iR1200 RS-232 MODEM DATA IGNITION Figure 5 – Cabling Diagram (Fixed Environment) NOTE: DCE (data communication equipment) refers to your iR1200 Modem DTE (data terminal equipment) refers to your computer or mobile device.
Getting Started 5 Plug the AC power cord into the 2-prong polarized power jack located on the rear panel of the modem. Plug the other end into a 120VAC-wall outlet. 6 Insert the ignition bypass plug into the 4-prong polarized IGNITION jack located on the rear panel of the modem (refer to Figures 2 and 3 on page 11). 7 The STATUS Led light will be solid RED. This indicates that the modem is attempting to register with the iDEN network.
iR1200 Modem Signal Color Indication CTS Green (Off) Clear To Send from modem is asserted (not asserted). DTR Green (Off) Data terminal equipment is ready (not ready). DSR Green (Off) Modem is ready (not ready). STATUS Solid Red The modem is searching for a signal within the Nextel network. If the modem status changes from blinking green back to solid red, the signal has been lost and the modem is attempting to re-acquire.
Getting Started The following tables describe the STATUS indicators for the Packet Data and Circuit Switched Data operating modes. Packet Data STATUS Blinking Green In-range (modem is connected to the Nextel network) but idle (but not passing data). STATUS Blinking Green The modem is in use – Nextel network communication is active and is passing data.
iR1200 Modem 20 nextel.
Installing iDEN Packet Data Applet Installing iDEN Packet Data Applet In this chapter, you will learn how to install the iDEN Packet Data Applet. The applet enables connectivity for the iR1200 modem connected to a laptop or mobile device and allows you to monitor the service and modem status such as signal strength.
iR1200 Modem NOTE: Please check the Nextel.com website for the latest hardware and installation requirements. Before You Begin Windows must have a Dial-up Networking Version 1.3 or later and the TCP/IP protocol Installed. NOTE: If the version of your Dial-up Networking is earlier than v1.3, please go to www.microsoft.com to obtain an upgrade. ! Before proceeding, please check that your computer has a network card or security program that prevents IP address changes.
Installing iDEN Packet Data Applet The following table describes steps to download and install the iDEN data packet applet. Windows 95/98/ME 1 Access the Nextel website by entering www.nextel.com. From the Nextel Home Page, select Services Nextel Online. The Nextel Online Services page appears. 2 From the Nextel Online page, find and select Wireless Web Access PacketstreamGold. 3 The Packetstream Gold Service page appears. 4 Click the Download Packetstream Gold Software (PC Only) link.
iR1200 Modem computer. IMPORTANT: When you have finished downloading the program, you MUST connect the data cable to your modem and computer before proceeding further. 7 Find the program in the appropriate folder and double-click the Setup.exe to launch the program to initiate the installation process. NOTE: The setup.exe will be contained in a zip or compressed file. 8 Click Next to accept the default Program Folder, iDEN Data Modem Applet.
Installing iDEN Packet Data Applet 16 Click OK to the message stating that you “must maximize the ‘Communication Settings’ window…”. 17 Click Communication Settings on your taskbar to maximize the window. The Communication Settings window opens. NOTE: Check to make sure that your modem is turned on and connected to your computer before continuing with the installation.
iR1200 Modem to connect to the modem. 19 The Packet Data Configuration window opens. Select No, I would like to configure my modem later or my modem has already been configured then click Next. 20 The Installation Complete window opens. Select Finish on the following screens to complete the installation process. 21 The Setup Complete window opens. Click Finish. Windows NT NOTE: Administrative rights are required to install the software on Windows NT.
Installing iDEN Packet Data Applet 2 From the Nextel Online page, find and select Wireless Web Access PacketstreamGold. 3 The Packetstream Gold Service page appears. 4 Click the Download Packetstream Gold Software (PC Only) link. The Download Packetstream Gold Software page appears. 5 Scroll down the page to find and select either Nextel Online Packetstream Gold Service Install link or the Download Now link located that the bottom of the page.
iR1200 Modem 13 The Choose Destination Location window opens. Click Next to accept the default destination folder, C:\Program Files. 14 The Select Program Folder window opens. Click Next to accept the default program folder, iDEN Packet Data Applet. 15 After the files are copied, the Question window opens. Click Yes to add a shortcut to your taskbar then click OK to continue. 16 An additional Information window opens. Click OK to continue with the installation. 17 The Add/Remove Hardware window opens.
Installing iDEN Packet Data Applet 24 The Remove Access Service window opens. Click Add. 25 The RAS Device window opens. Verify that the correct COM port is displayed in the RAS Capable Device box then click OK. NOTE: If the Motorola iDEN plus Series modem is not displayed in the RAS Capable Device box, click the Install Modem button to install the modem again. 26 The Remote Access Setup window now displays the added COM port.
iR1200 Modem 33 Select the following value on the Communication Settings window: • Click the Auto Detect to have the software automatically check for the COM Port or select the appropriate COM Port (typically COM1) • Multiple Baudrate should be unchecked • Baud Rate: 19200 (bps) The program will check the communication settings and attempt to connect to the modem. 34 The Packet Data Configuration window opens.
Installing iDEN Packet Data Applet process. 36 The Setup Complete window opens. Click Finish. Windows 2000 NOTE: Administrative rights are required to install the software on Windows 2000. Contact your IT Representative or Systems Administrator for assistance. 1 Access the Nextel website by entering www.nextel.com. From the Nextel Home Page, select Services Nextel Online. The Nextel Online Service Page appears. 2 From the Nextel Online page, find and select Wireless Web Access PacketstreamGold.
iR1200 Modem status window opens while the files are copying. 9 The Installshield Wizard screen appears during the setup process. 10 Click Next on the iDEN Packet Data Applet Setup screen. 11 The iDEN License Agreement screen appears. Select Yes to accept the terms of the agreement and proceed with the installation. 12 The iDEN Packet Data Applet Setup window will prompt you to enter a Username and Company. Enter the appropriate information and click Next.
Installing iDEN Packet Data Applet that your modem is connected and click Next. 21 The Digital Signature Not Found window opens. Click Yes to continue the installation. 22 The Modem Installation Finish window opens. Click Finish. 23 The Phone and Modem Options window reopens with the Modems tab selected. Verify that the Motorola iDEN plus Series modem appears on the list. Click OK. NOTE: Check to make sure that your modem is turned on and connected to your computer before continuing with the installation.
iR1200 Modem appropriate COM Port (typically COM1) • Multiple Baudrate should be unchecked • Baud Rate: 19200 (bps) The program will check the communication settings and attempt to connect to the modem. 25 The Packet Data Configuration window opens. Select No, I would like to configure my modem later or my modem has already been configured then click Next. 26 The Installation Complete window opens. Select Finish on the following screens to complete the installation process.
Setting Up Windows Components Setting Up Windows Components In this chapter, you will learn how to set up Windows components and verify their installation. This chapter includes: Verifying Dial-Up Networking Page 35 Verify TCP/IP Installation Page 36 Install Dial-Up Adapter Page 39 Verify Dial-Up Networking This section describes the procedures for verifying dial-up networking on your Windows computer.
iR1200 Modem Windows NT 1 From your desktop, double-click the My Computer icon to open the My Computer window. 2 Double-click the Dial-Up Networking icon to open the Dial-Up Networking window. 3 The Dial-Up Networking window opens and displays the Phone book entry to dial heading. If the Dial-Up Networking window displays the Install prompt then dial-up networking has not been installed. 4 Click Close to close the Dial-Up Networking window.
Setting Up Windows Components Windows 95/98/ME 1 From your desktop, double-click the My Computer icon to open the My Computer window. 2 Double-click the Control Panel icon to open the Control Panel window. 3 Double-click the Network icon to open the Network window. 4 Scroll down the list to find TCP/IP Dial-Up Adapter. • If you see TCP/IP Dial-Up Adapter in the list, click OK; you have TCP/IP installed and can proceed with installation.
iR1200 Modem Windows NT/2000 In most cases the TCP/IP protocol was installed automatically. However, for Windows NT and 2000, TCP/IP may not have been included in the standard installation. The following steps describe how to check that TCP/IP is in fact installed, and if necessary add the TCP/IP protocol. NOTE: This may require that you contact your IT Representative or System Administrator. 1 From your desktop, select Start Settings Network and Dialup Connections Local Area Connection.
Setting Up Windows Components Installing the Dial-Up Adapter The following table describes the steps for installing the Dial-Up Adapter. Windows 95/98/ME 1 From the Select Network Adapter window, highlight Dial-Up Adapter in the Network Adapters list. 2 Under Manufacturers, highlight Microsoft. Click OK. 3 The Select Network Component Type window opens. Highlight Adapter. Click Add. 4 The Select Network Adapters window opens. 5 To verify that the adapter was added, from Start, select Settings.
iR1200 Modem the connection wizard. Click Next. 3 Select I want to set up my Internet connection manually as above, then click on Next. 4 Select I connect through a phone line and a modem then click on Next. 5 Enter the new phone number: • Packet Data enter: s=2 • Circuit Switched enter: ISP Phone Number Click on the Advanced button. 6 The Advance Connection Properties window opens. On the Connection tab, select PPP and for Logon procedure select None. 7 Click on the Addresses tab.
Manual Modem Configuration Manual Modem Configuration In this chapter, you will learn how to manually add a modem, configure the modem drivers and create a dial-up networking connection for Nextel. NOTE: Use these instructions only if you did not previously install the iDEN Packet Data Applet. This chapter includes: Modem Configuration – Windows 95/98/ME Page 41 Modem Configuration – Windows NT 4.
iR1200 Modem from a list box. Click Next. 6 The Install New Modem/Modem Selection window opens. Under Manufacturer, select Standard Modem Types. Under Models, click Standard 19200 bps Modem. Click Next. 7 Select the COM port that you will be using to connect to the modem (i.e., COM1, COM2, or COM3), then click Next. NOTE: If you are not sure which COM port to use, begin with COM1.
Manual Modem Configuration • Use Flow Control and • Hardware (RTS/CTS) • If the Duplex option is present, select Full. 5 Click OK to close the Advanced Connection Settings window. 6 Click OK (or Close) to close the Standard 19200 bps Modem’s Properties window. 7 Click Close to close the Modem’s Properties window. 8 Click Close to close the Control Panel. 9 Continue with the steps to Create a Dial-Up Networking Connection.
iR1200 Modem procedure creates the iR1200 Modem icon in the Dial-Up Networking window. 6 In the Dial-Up Networking window, right click iR1200 Modem. Click Properties. 7 The iR1200 Modem Network window opens. Click the Server Types tab. NOTE: For packet data, country code and area code (under the General Tab) should always be blank to allow s=2 to be the telephone number. 8 Under Type of Dial-Up Server, select PPP. Under Allowed Network Protocols, ensure that the box next to TCP/IP is checked.
Manual Modem Configuration 2 The Modems Properties window opens. Under the General tab click Add. 3 The Install New Modem window opens. Select Other then Next. 4 The Install New Modem/Hardware Installation window opens. Check the Don't run the Hardware Installation Wizard box. Click the Next button. NOTE: If this option is not present, proceed to the next instruction. 5 The Install New Modem/Modem Detection window opens. Check the Don't detect my modem; I will select it from a list box. Click Next.
iR1200 Modem occur and Windows NT will not recognize the Standard 19200 bps modem. 12 The Add RAS Device window opens. Make sure the proper COM port for your modem connection is selected. Click OK. 13 The Remote Access Setup window now shows the added COM port. Click Continue. 14 The system automatically configures the appropriate settings. 15 Continue with the steps to Configure the Modem Driver. Configure the Modem Driver 1 From the Modems Properties window, select the Standard 19200 bps Modem.
Manual Modem Configuration 5 Click OK to close the Advanced Connection Settings window. 6 Click OK (or Close) to close the Standard 19200 bps Modems Properties window. 7 Click Close to close the Modem's Properties window. 8 Click Close to close the Control Panel. 9 Continue with the steps to Create a Dial-Up Networking Connection. Create a Dial-up Networking Connection 1 With the My Computer window open, double-click the Dial-Up Networking icon. 2 The Dial-Up Networking window opens. Click New.
iR1200 Modem Edit entry and modem properties from the drop-down list. 9 The Edit Phonebook Entry window displays. Click the Server tab. 10 In the Dial-up server type, select PPP. Under Network protocols, check the box next to TCP/IP. Remove the check marks from all other selection boxes. Click the TCP/IP button. 11 The PPP TCP/IP Settings window opens.
Manual Modem Configuration 5 The Modem Detection window opens. Under Manufacturer, select (Standard Modem Types). Under Models, click Standard 19200 bps Modem. Click Next. 6 The Port Selection window opens. Highlight the COM port that you will be using to connect to your modem (i.e., COM1, COM2, COM3, etc.). Click Next. 7 The Digital Signature Not Found window opens. Click Yes to proceed. 8 The Modem Installation Finish window opens. Click Finish.
iR1200 Modem 7 The Setting up your Internet connection window opens. Select I connect through a phone line and a modem and click Next. 8 The Choose Modem window opens. From the drop-down box, select Standard 19200 bps Modem and click Next. 9 The Internet Connection, Step 1 window opens. Enter a temporary telephone number (this phone number will be modified in Modem Properties later in the configuration). Make sure that the Use area code and dialing rules is NOT checked. Click Advanced.
Manual Modem Configuration • Always use the following – should remain unchecked Under DNS server address: • My ISP automatically provides a DNS address – should remain checked • Always use the following – should remain unchecked. Click OK. 12 The Internet Connection, Step 2 window opens. User name and password are not required fields. Click Next. You will receive two warning boxes asking if you want to continue with a blank user name and a blank password. Click Yes on both boxes.
iR1200 Modem 5 The iR1200 Modem window opens. Select the General tab. In the Phone number box, erase the temporary phone number previously entered: • For Packet Data enter: s=2 • For Circuit Switched Cellular enter: the ISP phone number Click OK. 52 nextel.
Modem Profiles and Settings Modem Profiles and Settings In this chapter, you will learn how to use AT commands to setup parameters and configure the iR1200 modem for usage.
iR1200 Modem HyperTerminal Setup A HyperTerminal session must be setup for you to enter AT commands. The following table outlines steps to setup a HyperTerminal session for the iR1200 modem: 1 From your computer, locate and select the HyperTerminal program. 2 The Connection Description screen appears. 3 Type a description of the connection in the Name: box. 4 Select the dial function (red and yellow phone icon) and click OK. 5 The Connect To screen appears. 54 nextel.
Modem Profiles and Settings 6 Select the appropriate communication port (typically COM1) from the “Connect Using:” drop-down list then Click OK. 7 The COM1 Properties screen appears.
iR1200 Modem • Parity: None • Stop Bits: 1 • Flow Control: Hardware 9 Click OK when all the parameters have been selected. 10 Test to make sure that you have established communication with the modem by typing the AT command “ATi4” and pressing Enter. 11 You should see a message “Nextel, iDEN OK” or “Nextel, iDEN 0”.
Modem Profiles and Settings Configuring With AT Commands Modem Initialization The iR1200 modem’s factory default image 2 is configured to start up with packet data.
iR1200 Modem Configuration Command Syntax AT&F Expected Return Code(s) OK Activate DTR Monitoring The DCE does not monitor the DTR line of the DTE/DCE physical connection. This is the default factory setting. To activate DTR monitoring in the DCE, you must apply the following command.
Modem Profiles and Settings 0,0,0 (Insert appropriate IP address where X appears.) Expected Return Code(s) ! OK IMPORTANT INFORMATION: Customers cannot ping a Non Routable IP address when provisioned due to the NAT (Network Address Translator) Server. This server attaches a Class C Public IP Address to a Private Class A Non Routable IP address for a specific period of time to browse the public internet.
iR1200 Modem Mobile IP Activation The modem makes use of mobile IP to manage a truly mobile computer. You may use a Mobile IP stack on the computer or use the Mobile IP stack built into the modem. By default, the modem is configured to work with a third-party stack. If you desire this mode of operation, skip ahead to the “Configure Encryption Settings”. Otherwise, you must activate the Mobile Node functionality within the modem as well the security-related parameters.
Modem Profiles and Settings AT Command MIP Authentication Key Command Syntax AT+WV301=”AAAXXX” (Make sure that the Authentication Key Name is entered with the quotation mark. Substitute the values within the quotation with the one supplied by your system administrator or service provider.) Expected Return Code(s) OK Mobile IP Security Parameter Index (SPI) The SPI is similar to the Authentication Key in that the modem and the home Agent must have identical values registered for the computer.
iR1200 Modem (Insert appropriate prefix length where X appears.) Expected Return Code(s) OK Header Compression This command enables or disables TCP header compression options. Some DTE-side stacks (such as PPP) will negotiate local header compression independently from this setting. To disable header compression, apply this command.
Modem Profiles and Settings IMPORTANT: These settings are stored on the modem’s Random Access Memory (RAM) and are lost when the modem is turned off unless stored in the modem’s non-volatile memory. The iR1200 modem can store up to three profile or image. By default, image 2 is loaded when the modem is powered on. We recommend that you save this setting to the first profile/image.
iR1200 Modem 64 nextel.
AT Commands AT Commands This chapter describes common AT commands that can be applied to the iR1200 modem. This chapter includes: General AT Commands Page 65 User Image Profile Commands Page 66 Registration, Reset, and Authentication Commands Page 66 Network Status Commands Page 66 Other Useful Commands Page 67 General AT Commands Command Usage Action AT AT Checks communication. ATEx ATE0 or ATE1 Sets echo on or off. AT&V AT&V Displays modem parameters.
iR1200 Modem User Image Profile Commands Command Usage Action ATz ATz0, ATz1, or ATz2 Sets the specified image as the active image. AT&Wx AT&W0, 1, or 2. Writes active image to the specified profile Registration, Reset, and Authentication Commands Command Usage Action AT+wvreset AT+wvreset Resets the modem and performs power cycle. AT+wvmr AT+wvmr=’xxxx’ (0000) Mater Resets the modem. AT+wvcsk AT+wvcsk=’xxxx’ (0000) Changes authentication service key.
AT Commands AT+WS53? AT+WS53? Checks Signal Quality AT+WS50? AT+WS50? Check Signal Strength AT+WPSTATE AT+WPSTATE Checks mobile IP registration AT+WPREG AT+WPREG DTE IP Address Other Useful AT Commands The following table outlines other common AT commands for your reference. Answer This command instructs the DCE to immediately connect to the call and start the answer sequence, as appropriate for the selected service.
iR1200 Modem Values: 1 = Enabled command mode character echo. Dial This command instructs the DCE to originate a call. When the DCE receives the dial string from the computer, all non-numeric characters in the Dial String that are not recognized dial-modifiers are ignored. This allows the DTE to request modem numbers containing unsupported dial modifiers, hyphens, parenthesis, and other punctuation.
AT Commands Hang-up This command instructs the modem to terminate the active call. Command Action H ATh Query Range Request Modem Information This command causes the modem to issue a string to provide product information. Command Action I ATi Query Range Parameter Values: 0 = OK Response code 1 = iDEN DTE/DCE Specification Version 2 = Software Model 3 = Product Model 4 = Product Manufacturer Go Online This command causes the modem to enter the online state from the online command state.
iR1200 Modem Query Range Pulse Dialing This command selects pulse dialing. It is provided for compatibility purposes. Command Action P Atp Query Range Quiet Mode This command controls whether or not the result codes are sent to the computer. If turned on, the Result Code Format and Extended Result code commands may further modify the result codes.
AT Commands Action ATt Query Range Verbose Result Codes This command sets your preference for the result code format. It allows the computer to select either Terse or Verbose result code formats. Command V Action ATv Query AT&v Range Parameter Values: 0 = Numeric result code format 1 = Verbose result code format Extended Result Codes This command provides an extended result code selection.
iR1200 Modem appropriate, but does not return the NO DIALTONE result code. 4 = The modem may return either the BUSY or NO DIALTONE result code, if appropriate. Restore User Defaults This command causes the modem to reset all parameters and S-registers to their user-defined default values. There are three sets of user defaults (or images). The parameter selects between which image is being requested.
AT Commands Range Parameter Values: 0 = DCD always on 1 = The modem turns on the DCD to indicate the presence of a connection, and turns off the DCD to indicate the loss of connection. DTR Behavior This parameter determines how the computer responds when the DTR line is changed from the ON condition to the OFF condition during the online data state.
iR1200 Modem Action AT&f Query AT&v Range Local Flow Control (Traditional) This parameter selects the type of flow control used between the computer and the modem while in data transfer mode. This command is supported for backward compatibility purposes. This command sets the method of flow control for both directions of the computer-to-modem interface, while the +IFC command allows for a separate setting for each direction.
AT Commands Query Range Local Character Framing This parameter determines the local serial port asynchronous data framing. The second parameter is needed only if you select fewer than eight data bits.
iR1200 Modem DCE_by_ DTE Parameter Values: 0 = No flow control was set by DTE. 1 = XON/XOFF; do not pass XON/XOFF characters to the remote DCE. 2 = RFR active/inactive flow control 3 = XON/XOFF; Pass DC1/DC3 characters to the remote DCE in addition to acting upon local flow control. DTE_by_ DCE Parameter Values: 0 = No flow control was set by DTE.
AT Commands 38400 = Transmission speed in bits per second. 57600 = Transmission speed in bits per second. 115200 = Transmission speed in bits per second. Lock/Unlock the DCE When the DCE is locked, communication over the serial port to the modem is suspended. NOTE: If the PIN was removed (by setting its value to the empty string (“ ”), the DTE must still specify the PIN, represented by the empty string.
iR1200 Modem Command Action +WCPN AT+wcpn=, Query Range AT+wcpn=? Parameter Values: A PIN is stored as a series of alphanumeric characters, with a maximum length of 8 characters. If more than 8 characters are set as a PIN, only the first 8 are recognized. Packet Data Sleep Timer This timer controls the length of time the DCE stays on a packet channel though no traffic is actively being transferred.
AT Commands Query AT+wv312? Range AT+wv312=? Parameter Values: 68-1500 = MTU Value Range 1006 = Default Value Select Mobile IP Client This parameter activates/deactivates the Mobile Node client in the DCE. The mobile host can operate in two modes to access the iDEN packet data network. Command +WV300 Action AT+wv300 Query AT+wv300? Range AT+wv300=? Parameter Values: 0 = Activate Mobile Node in DCE. 1 = Deactivate Mobile Node in DCE.
iR1200 Modem Parameter Values: The authentication Key parameter is a text string of up to 32 characters. Unlike most text-string parameters, the Authentication key is a text representation of a hexadecimal number. Therefore, only the characters 0-9 and A-F are acceptable. (The lower case character, a-f is also acceptable). NOTE: Although the parameter represents a numeric value, the parameter is actually a text string, so the parameter must be enclosed in quotation marks.
AT Commands NOTE: This parameter is applicable only when the Mobile Node Client in the DCE is activated. Command +WPNEI Action AT+wpnei<”address”> Query AT+wpnei? Range AT+wpnei=? Parameter Values: An IP Address consists of up to 15 characters, and is in the format “ddd.ddd.ddd.ddd”. 0.0.0.0. = Default value DTE IP Address Prefix Length The prefix-length is the number of contiguous bits in an IP address that makes up the network prefix (or network number plus subnet number) of the IP address.
iR1200 Modem Command +WV308 Action AT+wv308, , Query AT+wv308? Range AT+wv308=? Parameter Values Encryption: 0 = Disabled Parameter Values – Firm Offer: 0 = Encryption setting is a negotiable preference. Parameter Value – Key Size: 1 = Vancouver Encryption 1 = Encryption setting is not negotiable. 40-64 = Encryption key size 40 = Default value DTE Stack This command sets the protocol for communication between the DEC and the DTE.
AT Commands WDS Stack This command changes the data mode of the modem between circuit-switched data and packet data. Command +WS46 Action AT+ws46 Query AT+ws46? Range AT+wv46=? Parameter Values: 23 = iDEN Circuit-switched data/fax 24 = iDEN packet data 252 = Local Data Services Service Class This command switches between normal circuit-switched data mode and Class 2 fax mode. This setting has no effect during the packet data service.
iR1200 Modem Action AT+ws198
AT Commands Parameter Values: 1-255 = Seconds 30 = Default value Comma Dial Modifier Timer This command allows the DTE to set the duration of the pause associated with a comma (,) dial modifier. Command S8 Action AT+s8 Query AT+s8? Range AT+s8=? Parameter Values: 0-255 = Seconds 2 = Default value Circuit Data Idle Timer This command specifies an idle line timeout for online data mode.
iR1200 Modem 86 nextel.
S-Registers S-Registers In this chapter, you are will learn about S-registers and how to configure registers for your iR1200 modem. This chapter includes: S-Register Page 87 Programming S-Register Page 87 Reading S-Register Page 88 Supported S-Register Page 88 S-Registers S-registers are memory locations in the modem that you can program to meet your communication needs. S-register parameters are numbered from 0 (zero) to 255.
iR1200 Modem ! If you write to an S-register that is not programmable or if the value you assigned is invalid, the modem will still return an OK message to the computer screen. The attempted changes will not affect the S-register values. . Reading an S-Register Value The following table describes how to read a value for an S-Register. 1 From the command mode, type ATSn (n= the number of the S-register that you want to read) and press ENTER. 2 The value of the requested S-register displays.
S-Registers Register # Function Valid value ranges from 0 (zero) to 255. 0 (zero) is the default value. 2 Escape (ESC) Code Character. Specifies the ASCII character to be used to escape from either data or online mode to command mode. Valid value ranges from 0 (zero) to 127. 43 or the ASCII plus (+) key is the default value. 3 Command Line Terminating Character. Specifies the ASCII character to be used to terminate a command line without carrying out any command that might be issued.
iR1200 Modem Register # 8 Function Command Dial Modifier Time. Valid value ranges from 0 (zero) to 255 seconds. 2 (seconds) is the default value. 10 Automatic Disconnect Delay. Determines the amount of time between loss of carrier and disconnection of the data call. Valid value ranges from 1 to 254 tenths of a second. 14 (1.4 seconds) is the default value. 12 Escape Code Timer. Determines the time duration within which the escape code must be sent by the computer to escape from online command mode.
Troubleshooting Troubleshooting This chapter describes typical configuration problems and provides instructions on how to troubleshoot issues with the iR1200 modem. This chapter includes: Common Problems Page 91 Error Messages Page 93 Diagnostic Commands Page 94 Extended AT Command Page 95 Extended Error Result Codes Page 95 Common Problems The following table identifies the most common problems that may occur while setting up and using your modem for data calls.
iR1200 Modem Symptom • • • Troubleshooting Tips modem. The cable is connected to the correct port. The correct port is specified in your communication software. The modem is set to the same baud rate specified in the communication software. The NO CARRIER message displays when the modem attempts data calls. Make sure that the S7 register contains a value greater than or equal to 60 by issuing an AT&V command or by explicitly setting ATS7=’x’ (where x is, enter any number between 1 and 255).
Troubleshooting Symptom Troubleshooting Tips Modem keeps dropping connection. Check the signal strength and signal quality icon to be sure the signal is not weak or poor. Modem does not respond to hang-up command from the software’s command mode. Make sure that: • The Drop DTR on Hang-up is enabled in the communication software. • The hang-up string setting is ‘+++ATH’. Computer screen appears distorted. Turn off Auto Baud by initiating AT+IPR command.
iR1200 Modem Message BUSY MODEM INITIALIZATION FAILED NO CARRIER Explanation • An invalid parameter was entered. The command line is ready for another command. Make sure that the command (and parameter) that you entered are valid. The number you called is busy. You should try the call again later. The modem is ready to accept another command. Your communication software assumes that Auto Baud is supported by the modem. Make sure that: • That the baud rate = 19200 bps.
Troubleshooting any ongoing data connections. 3 Establish basic computer to modem communication. 4 Administer the following AT command to query for the last “Extended Error Code”. Extended Error AT Command AT Command Return Product Information Command Syntax AT+CEER Expected Return Code(s) See Extended Error Result Codes Table Extended Error Result Codes Extended error result codes report the network reason why a data connection failed.
iR1200 Modem Code General Description 268 Invalid DTE-IP address was specified (+WPNEI). 269 Invalid Home Agent address was specified (+WV305) 270 Invalid MIP Security Parameter index was specified. 271 DCE IP address matched Home Agent IP Address (+WV304, +WV305). 272 The DTE tried to lock or unlock the DCE using an incorrect PIN. 275 An AT Command is not compatible with the current/active data service. Packet Data Operation 519 Requested level of encryption is not allowed.
Troubleshooting Code 1027 General Description SLIP/PPP link terminated. Circuit Data Operation 1280 No information is available. 1290 Unspecified Transmit Phase A Error. 1300 Unspecified Transmit Phase B Error. 1320 Unspecified Transmit Phase C Error. 1330 Unspecified Transmit Phase D Error. 1350 Unspecified Receive Phase B Error. 1360 Unspecified Receive Phase C Error. 1370 Unspecified Receive Phase D Error. Network Error Codes 1558 No route to specified transit network.
iR1200 Modem Code General Description 1594 Bearer capability is not presently available. 1593 Bearer capability is not authorized. 1599 Service or option is not available. 1601 Bearer service is not implemented. 1602 Channel type is not implemented. 1615 Service or option is not implemented 1624 Incompatible destination. 98 nextel.
Safety Notice Safety Notice The following information is important for the safe and efficient operation of the iR1200 modem. Please read this safety notice before operating the modem. Safe and Efficient Operation Guidelines Your modem contains a transmitter and receiver. When it is ON, it receives and transmits radio frequency (RF) energy. The modem operates in the frequency range of 806 MHz to 870 MHz and utilizes the digital modulation techniques. This product is authorized by FCC Rule Part 47CFR2.
iR1200 Modem Hearing Aids The modem may interfere with hearing aid devices. Individuals who experience such interference should consult the hearing aid manufacturer to discuss alternative solutions. Other Medical Devices Individuals who have other medical devices not specifically mentioned in this safety notice may want to consult their physician or the manufacturer of the device to determine if it is adequately protected from external RF energy.
Copyright and Trademark Copyright and Trademark © 2003 Nextel Communications, Inc. Nextel and the Nextel logo are service marks, trademarks and/or registered trademarks owned by Nextel Communications, Inc. All other product or service names are the property of their respective owners. All trademarks, service marks and trade names are protected by state, federal and/or international trademark laws. All rights reserved.
iR1200 Modem 102 nextel.
Appendix A: Glossary Appendix A: Glossary This glossary contains terms and definitions used within this guide. It is by no means exhaustive of terms that you may come across. ASCII American Standard Code for Information Interchange. A standard set of 128 characters, symbols and control codes used for computer communications. ASCII characters require 7 bits of data to send, but are often sent 8 bits at a time with the extra bit being a zero.
iR1200 Modem through. Circuit Switch was originally developed for the analog-based telephone system in order to guarantee steady, consistent service for two people engaged in a phone conversation. Command Mode The mode that accepts AT commands. Also known as Terminal Mode. When your modem is in this mode, it is waiting to receive AT commands that you type from your communication software.
Appendix A: Glossary Differential GPS A procedure of correcting GPS solutions to achieve improved position accuracy. Differential GPS provides 2 to 5 meter position accuracy. Differential accuracy is obtained by applying corrections determined by the stationary Differential Reference Station to the GPS data collected by the RPU (receiver processing unit) on-board the vehicle. DNS Domain Name Server. This is what converts names of domains (ex. : www.nextel.com) into IP addresses (ex. : 170.206.225.22).
iR1200 Modem operated by the U.S. Department of Defense but is available for general use around the world. GPS Antenna An antenna designed to receive GPS radio navigation signals. GPS Processor An electronic device that interprets the GPS radio navigation signals (received by the GPS antenna) and determines a location solution. The GPS processor may also be able to apply (and determine) differential GPs corrections. GPS Receiver The combination of GPS antenna and GPS processor.
Appendix A: Glossary Kbps Kilobits per second. Generally represented at 1000 bits per second. Laptops Portable computers, such as notebooks and sub-notebooks. Local Area Network (LAN) A computer network that spans over a relatively small area. Most LANs are confined to a single building or group of buildings. Mobile IP An IP enhancement that provides forwarding of traffic to moving users. It uses agents in the user’s home network and in all foreign networks.
iR1200 Modem Packet of Data A bundle or block of data, organized in a specific way for transmission. Parallel Port A low speed port, usually located on the rear of a computer which usually connects to printers. Parallel ports transmit data simultaneously over eight “parallel wires” one byte at a time (as opposed to a serial port, which transmits data one bit at a time). Parity Bit Parity is a process for detecting whether bits of data have been altered during transmission.
Appendix A: Glossary RAM Random Access Memory is the working memory of the computer where you can enter information and call up data. Routable IP Address (Public IP Address) A communications protocol that contains a network address as well as a device address, allowing data to be routed from one network to another. Examples of routable protocols are SNA, OSI, TCP/IP, XNS, IPX, AppleTalk and DECnet. RS-232 A communication standard for digital data. Specifies a number of signal and control lines.
iR1200 Modem will be delivered in the same order in which they were sent. IP acts as a postal system, allowing you to address a package and drop it in the system, but doesn’t provide a direct link between you and the recipient. TCP/IP, on the other hand, establishes a connection between two hosts so that they can send messages back and forth for a period of time. Terminal Mode The mode that accepts AT commands. Also known as Command Mode.
Index Index A DTE · 4, 14, 15, 30, 34, 37, 39, 40, 41, 48, 49, 53, 54, 55, 56, 57, 58, 65, 66, 79 DTR · 2, 3, 15, 27, 30, 45, 62 AC Power Adapter · 3 B Bits · 29 C Circuit data · 8 COM1 · 29 Coverage · 5 CTS · 15 Customer Care · 5, 6 D Data bits · 29 data packet applet · 18 DB-9-P · 14 DB-9-S · 14 DCD · 2, 3, 27, 31, 44, 45, 78 DCE · 3, 14, 30, 37, 39, 40, 41, 48, 49, 50, 51, 52, 53, 56, 58, 65, 66, 78 DSR · 15 RFM-4000-5015 Rev1 E Electronic Devices · 73 Encryption · 54 F Flow control · 29 G GPS
iR1200 Modem IMEI · 6 Installation Guide · 3 R Radio Frequency · 73 RAM · 17 required components · 3 RS-232 · 13 RTS · 15 Rugged Modem · 8 Rx · 15 L LED indicators · 15 M S mobile IP · 32 Mobile IP · 2, 4, 27, 32, 33, 51, 52, 81 SIM ID · 6 SLIP · 2, 3, 27, 31, 32, 51, 55, 67 Stationary Environment · 14 Stop bits · 29 P Pacemakers · 73 Packet Data · 8 Packet StreamGold · 18 Parity · 29 PIN · 3, 33, 49, 50, 66, 82 PPP · 2, 27, 31, 32, 34, 51, 55, 67, 82 processor · 17 profile · 35, 38, 47 T TCP/IP Pr