Nextel RoadRunners Scanner (BRR-L) by Baracoda Programming Guide
Nextel RoadRunners Scanner Programming Guide Nextel RoadRunners Scanner (BRR-L) Programming Guide Contents 1 Introduction............................................................................................................................................................1 2 General Configuration...........................................................................................................................................2 2.1 Reset Default Settings: ........................................
Nextel RoadRunners Scanner Programming Guide 1 Introduction This manual contains the necessary barcodes to configure the parameters of your scanner. You can either print out this document to scan its barcodes or in some cases you can even scan the barcodes right off your computer screen. The RoadRunners scanner can be programmed by scanning barcode labels which contain commands for the 1D decoder. The programming labels must be Code128, with specific starting and ending characters.
Nextel RoadRunners Scanner Programming Guide 2 General Configuration 2.1 Reset Default Settings: Reading the "Default settings” label resets all scanner parameters to the default factory settings and switches it off. CAUTION: SCANNING THIS BARCODE WILL RESET THE DEFAULT SETTINGS OF THE SCANNER AND MAY RESULT IN THE LOSS OF STORED DATA. Reset defaults settings s et def aul t s \ V T \ V T t \ N U L \ N U L \ F F \ F F 2.
Nextel RoadRunners Scanner Programming Guide Switch on delay: 2 seconds Switch on delay: 0 second (*) s wi t ch on del ay : 2 s ecs \ V T \ V T z \ N U L \ S O H \ E T X \ F F \ F F s wi t ch on del ay : 0 s ec \ V T \ V T z \ N U L \ S O H \ S O H \ F F \ F F No Data Loss Mode Baracoda has developed a proprietary communication protocol for enhanced Bluetooth® transmission security. Every barcode sent to the handset must be acknowledged by the handset (i.e.
Nextel RoadRunners Scanner Programming Guide Programming procedure for “Set Timestamp” option START Read "Set Suffix (prefix)" label Read intermediary label Corresponding to the next character to set for the suffix (appendix 2 of this document) NO Finished *? YES Read "END of config" label END Set Timestamp “END of Config” END of Conf i g Set Ti mes t amp \ V T \ V T \ F N C 4 t \ N U L \ N U L \ L F \ L F \ L F \ L F E N D \ F F \ F F Note: The timestamp must comply with the follo
Nextel RoadRunners Scanner Programming Guide For example, to set the current time at May 16, 2007 3.25 P.M., the user will scan the following sequence: - “Set Timestamp” label, - “0” label, {YY} : 2007 - “7” label, - “0” label, {MM} : May - “5” label, - “1” label, {DD} : 16 - “6” label, - “1” label, {HH} : 15 (3:00 PM) - “5” label, - “2” label, {MM} : 25 - “5” label, - “0” label, {SS} : 00 - “0” label, - “END of config” label. 2.
Nextel RoadRunners Scanner Programming Guide An important reminder: if an acknowledgement (ACK) beep or storage of codes in memory is needed, the scanner must first be set to “No data loss mode” (see section 2.3). CAUTION: SCANNING ANY OF THE FOLLOWING THREE BARCODES WILL ERASE ALL CODES IN MEMORY. • REAL TIME mode: Erases all codes in memory and places the RoadRunners scanner in Real time mode. No other setting is changed.
Nextel RoadRunners Scanner Programming Guide Batch mode. Places the scanner in Batch mode. CAUTION: SCANNING THIS BARCODE ERASES ALL CODES IN MEMORY. Discharge barcode. CAUTION: SCANNING THIS BARCODE ERASES ALL CODES IN MEMORY Upl oad bat c h \ V T \ V T \ F N C 4 z \ N U L \ N U L \ F F \ F F \ V T \ V T d \ N U L \ S O H \ S O H \ F F \ F F 2.6 Beep and LED Settings These options can be used to enable or disable the beep and/or the LED. It is also possible to invert (swap) LED positions.
Nextel RoadRunners Scanner Programming Guide Beep Level Volume = LOW Beep evel Volume = HIGH beep l ev el : l ow beep l evel : hi gh \ V T \ V T \ F N C 4 \ D C 4 \ N U L \ S O H \ F N C 4 @\ F F \ F F \ V T \ V T \ F NC4 \ DC4 \ NUL \ S OH\ F N C4 A \ F F \ F F 2.6.1 Bluetooth® Commands Sniff Settings The higher the Sniff period, the higher the latency and the lower the power consumption. The default value is 150ms.
Nextel RoadRunners Scanner Programming Guide Security (PIN code) Settings The initial PIN code can be disabled or enabled by scanning the following barcodes: \ 2.
Nextel RoadRunners Scanner Programming Guide Programming procedure for “set suffix (prefix)” option.
Nextel RoadRunners Scanner Programming Guide 3 Symbology Settings 3.1 Symbology Default Settings Sets the default decoder settings for all the symbologies. Set Decoder Default Settings Set Dec oder Def aul t s \ VT \ VT \ F NC4 ~ \ NUL \ ET XAC\ NUL \ F F \ F F 3.2 Symbology Identifier The AIM Identifier (e.g. Code39, Code128) will be transmitted at the beginning of the barcode. More information about the AIM Identifier is available in Appendix 3.
Nextel RoadRunners Scanner Programming Guide 3.3 Disable All Symbologies Even if all symbologies are disabled, the RoadRunners scanner will still be able to read the programming barcodes included in this document. CAUTION: CARE SHOULD BE USED WHEN DISABLING ALL BARCODES AS IT MAY MAKE THE UNIT APPEAR TO BE MALFUNCTIONING SINCE NO SYMBOLOGY IS BEING READ.
Nextel RoadRunners Scanner Programming Guide 3.
Nextel RoadRunners Scanner Programming Guide 3.
Nextel RoadRunners Scanner Programming Guide 3.
Nextel RoadRunners Scanner Programming Guide 3.
Nextel RoadRunners Scanner Programming Guide 3.
Nextel RoadRunners Scanner Programming Guide 3.
Nextel RoadRunners Scanner Programming Guide 3.
Nextel RoadRunners Scanner Programming Guide 3.
Nextel RoadRunners Scanner Programming Guide UPC / EAN - check digit - UPC-E - transmitted (*) UPC / EAN - check digit - EAN-8 - transmitted (*) Enabl e UPCE c hec k di gi t t r ans mi s s i on Enabl e EAN8 c hec k di gi t t r ans mi s s i on \ V T \ V T \ F NC4 ~ \ NUL \ E OT L D\ S OHG\ F F \ F F \ V T \ V T \ F N C 4 ~ \ N U L \ E OT MD \ S OH G\ F F \ F F UPC / EAN - UPC number system - UPC-A transmitted (*) UPC / EAN - re-encoding UPC-A, UPC-E, EAN-8 - UPC-A transmitted as EAN-13 Enabl e UPCA
Nextel RoadRunners Scanner Programming Guide 3.13 Set Min or Max Length Option The procedure to be followed for each barcode is shown below: START Read "Start - Set min (Max) length" label Read intermediary label from the table below to select the desired symbology to configure Read intermediary label Corresponding to the next digit of the min (Max) length value to apply (as on a calculator). NO Finished? YES Read "END of config" label END Programming procedure for “set min (Max) length” option.
Nextel RoadRunners Scanner Programming Guide s et mi n l engt h Start – set min length \ V T \ V T \ F N C 4 ~ \ N U L \ S T X \ L F \ L F s et max l engt h Start – Set Max length \ V T \ V T \ F N C 4 ~ \ N U L \ E T X \ L F \ L F END of Conf i g End of config \ Last updated: 10/14/05 L F \ L F E N D \ F F \ F F © Baracoda 2005 23
Nextel RoadRunners Scanner Programming Guide APPENDIX 1: Symbology Table Header Selected Symbology Header Interleaved 2 of 5 SELECT ALL \ L F \ L F A \ L F \ L F Code 93 \ L F \ L F B \ L F \ L F \ L F \ L F C \ L F \ L F Code 128 / EAN 128 Standard 2 of 5 (Industrial 2 of 5) \ L F \ L F G \ L F \ L F \ L F \ L F H \ L F \ L F \ L F \ L F J \ L F \ L F \ L F \ L F K \ L F \ L F \ L F \ L F L \ L F \ L
Nextel RoadRunners Scanner Programming Guide APPENDIX 2: ASCII Table (A-Z, a-z, 0-9, Punctuation, Control Characters) Upper Case Letters (A-Z): Name Programming Bar Code Name A N \ L F \ L F A \ L F \ L F \ L F \ L F B \ L F \ L F \ L F \ L F C \ L F \ L F B \ L F \ L F N \ L F \ L F \ L F \ L F O \ L F \ L F \ L F \ L F P \ L F \ L F \ L F \ L F Q \ L F \ L F \ L F \ L F R \ L F \ L F \ L F \ L
Nextel RoadRunners Scanner Programming Guide Lower Case Letters (a-z): Name Programming Bar Code Name a n \ L F \ L F a \ L F \ L F \ L F \ L F b \ L F \ L F b \ L F \ L F n \ L F \ L F \ L F \ L F o \ L F \ L F \ L F \ L F p \ L F \ L F \ L F \ L F q \ L F \ L F \ L F \ L F r \ L F \ L F \ L F \ L F s \ L F \ L F \ L F \ L F t \ L F \ L F \ L F \ L F u \ L F \ L F \ L F
Nextel RoadRunners Scanner Programming Guide Punctuation: Name Programming Bar Code Name Programming Bar Code : SPACE Space : \ L F \ L F \ L F \ L F \ L F \ L F : \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F L F \ L F ; ! ! ; \ L F \ L F ! \ L F \ L \ F L
Nextel RoadRunners Scanner Programming Guide Decimal Numbers (0-9): Number Programming Bar Code Number Programming Bar Code 5 0 5 0 \ L F \ L F 0 \ L F \ L \ F L F \ L F 5 1 \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F \ L F 6 1 6 \ L F \ L F 1 \ L F \ L \ F L F \ L F 6 7 2 7 2 \ L F \ L F 2 \ L F \ L \ F L F \ L F 7 3 8 3 8 \ L F \ L F 3 \ L F \ L F \ L F \ L F 8 4 9 9 4
Nextel RoadRunners Scanner Programming Guide APPENDIX 3 For more information, see Symbology Settings => Symbology Identifier.
