INSTRUCTION MANUAL FOR NEXT LEVEL RACING WHEEL STAND *If you are using as a FLIGHT STAND please also refer to instructions included with your flight pack For assistance please contact: support@nextlevelracing.
Thank-you for purchasing a Wheel Stand If you require any support with your product please contact our friendly team at: support@nextlevelracing.com for a prompt response.
WHEEL STAND What’s In The Box: NEXT LEVEL RACING WHEEL STAND For assistance please contact: support@nextlevelracing.
WHEEL STAND Step 1: Ste Wheel Support Bar Unpack and unfold the wheel stand out of the box and slide out the wheel support bar. Step 2: Ste After finding the height you prefer for the wheel support bar, screw in 1 x LONG KNOB into the side hole of wheel stand. Repeat both sides. For assistance please contact: support@nextlevelracing.
WHEEL STAND Step 3: Screw in 1 x M8 10MM SCREW using M8 ALLEN KEY. Repeat both sides. Step 4: Install WHEEL PLATE to the wheel support bar using the 2 x M6 55MM SCREWS AND NUTS already installed to wheel plate. For assistance please contact: support@nextlevelracing.
WHEEL STAND Step 5: SKIP IF NOT ATTACHING GEAR SHIFTER LEFT HAND GEAR SHIFTER RIGHT HAND GEAR SHIFTER Attach the SHIFTER ARM into either side of the wheel support bar. Tighten in position using SHORT KNOB. Then attach SHIFTER BRACKET onto the SHIFTER ARM and tighten in position using SHORT KNOB.
WHEEL STAND ADJUSTING PEDAL PLATE & INSTALLING PEDAL STOPPER Step 7: ND TER To adjust pedal plate position, loosen the 2 x knobs underneath the pedal plate and slide plate out into preferred position and then tighten knobs. Photo below shows pedal plate when slid out to furthest position. For assistance please contact: support@nextlevelracing.
WHEEL STAND Step 8: Attach PEDAL STOPPER to the holes in pedal plate using the 2 x M6 15MM SCREWS + NUTS ATTACHING YOUR ELECTRONICS Step 9: The 6 x M6 20MM screws provided will suit most electronics on the market. LOGITECH® – WHEEL PLATE, SHIFTER BRACKET and PEDAL PLATE are pre-drilled for Logitech® equipment that allow hard mounting. THRUSTMASTER® - WHEEL PLATE, SHIFTER BRACKET and PEDAL PLATE are pre-drilled for Thrustmaster® equipment that allow hard mounting.
WHEEL STAND Step 10: (IGNORE IF YOU ARE NOT USING A THRUSTMASTER® T500 WHEEL. EVEN IF YOU ARE A T500 OWNER THE BRACKET IS ONLY OPTIONAL AND MANY CUSTOMERS DON’T USE) Use the 2 x M6 50MM SCREWS provide with the OPTIONAL T500 BRACKET to attach the bracket to WHEEL PLATE as well as the T500 wheel. The 2 x M6 50MM SCREWS will go through WHEEL PLATE and into your wheel. For assistance please contact: support@nextlevelracing.
FLIGHT STAND PICTURED AS A FLIGHT STAND BELOW USING OPTIONAL FLIGHT PACK. *FLIGHT PACK COMES INCLUDED WITH FLIGHT STAND M8 15MM SCREWS REPEAT BOTH SIDES For assistance please contact: support@nextlevelracing.
WHEEL STAND FULLY ADJUSTABLE For assistance please contact: support@nextlevelracing.
WHEEL STAND عم .الخطوة :1أفرغ املحتويات وأخرج حامل العجلة من العلبة واسحب قضيب دعم العجلة للخارج .يف الثقب الجانبي لحامل العجلة ،وكرر ذلك مع الجانب اآلخر X LONG KNOBالخطوة :2بعد الوصول لالرتفاع املفضل لقضيب دعم حامل العجلة ،اربط 1 .وكرر ذلك مع الجانب اآلخر M* ALLEN KEY،باستخدام X M8 10MM SCREWالخطوة :3اربط 1 .املثبتة بالفعل بلوحة العجلة x M6 55MM SCREWS AND NUTSعىل قضيب دعم العجلة باستخدام WHEEL PLATE 2الخطوة :4قم برتكيب .
WHEEL STAND CZ Krok 1: Rozbalte a rozložte z krabice ocelový stojan a vysuňte ocelovou tyč. Krok 2: Po nastavení preferované výšky tyče zašroubujte 1 X LONG KNOB do postranního otvoru v ocelovém stojanu. Proveďte po obou stranách. Krok 3: Zašroubujte 1 X M8 10MM SCREW pomocí M* ALLEN KEY. Proveďte po obou stranách. Krok 4: Nainstalujte WHEEL PLATE do ocelové tyče, použijte k tomu 2 x M6 55MM SCREWS AND NUTS, které jsou již nainstalované na ocelové desce.
WHEEL STAND NL Stap 1: Haal de stuurstandaard uit de verpakking en ontvouw hem, schuif de stuursteunstang uit. Stap 2: Nadat u de juiste hoogte hebt gevonden voor de stuursteunstang, schroef 1 X LONG KNOB in het gaat aan de zijkant van de stuurstandaard. Herhaal aan beide kanten. Stap 3: Schroef 1 X M8 10MM SCREW in met de M* ALLEN KEY. Herhaal aan beide kanten. Stap 4: Installeer WHEEL PLATE op de stuursteunstang met behulp van de 2 x M6 55MM SCREWS AND NUTS die al op de stuurplaat zijn geïnstalleerd.
WHEEL STAND FR Étape 1 : Sortez le support pour volant du carton, dépliez-le chariot mobile et tirez sa barre d’appui. Étape 2 : Après avoir ajusté la barre d’appui à la hauteur désirée, vissez la pièce 1 X LONG KNOB dans le trou latéral du support pour volant. Répétez cette procédure sur l’autre côté du support. Étape 3 : Vissez la vis 1 X M8 10MM SCREW à l’aide d’une M* ALLEN KEY. Répétez cette procédure des deux côtés.
WHEEL STAND IT Step 1: Disimballare ed estrarre il supporto guida dalla scatola, poi fare scorrere la barra di supporto. Step2: Una volta regolata l’altezza della barra, avvitare 1 X LONG KNOB nell’apposito foro del supporto guida. Ripetere su entrambi i lati. Step 3: Avvitare 1 X M8 10MM SCREW usando la M* ALLEN KEY. Ripetere su entrambi i lati. Step 4: Fissare la WHEEL PLATE alla barra di supporto utilizzando 2 x M6 55MM SCREWS AND NUTS prefissate sulla piastra.
WHEEL STAND ES Paso 1: Desembale y desplieque la base del volante de la caja y deslice el volante en la barra de soporte. Paso 2: Después de ajustar la altura que desee para la barra de soporte de la base del volante, atornille el 1 X LONG KNOB en el orificio lateral de la base del volante. Repita en ambos lados. Paso 3: Atornille el 1 X M8 10MM SCREW usando la M* ALLEN KEY. Repita en ambos lados.
WHEEL STAND DE Schritt 1: Auspacken Sie und entfalten Sie das Zentrierständer aus der Schachtel und schieben Sie die Radauflageleiste. Schritt 2: Nach dem Ausbilden der Höhe, die Sie für die Auflageleiste des Radstandes bevorzugen, schrauben Sie 1 X LONG KNOB in das Seitenloch des Radstandes ein. Wiederholen Sie für beide Seiten. Schritt 3: Schrauben Sie 1 X M8 10MM SCREW mit M* ALLEN KEY. Wiederholen Sie für beide Seiten.
WHEEL STAND AVAILABLE ACCESSORIES TO BUILD THE ULTIMATE COCKPIT For assistance please contact: support@nextlevelracing.
For assistance please contact: support@nextlevelracing.
