NEXT>>>ADVANCE www.nextadvance.com SP300 “Just Infusion” Programmable Syringe Pump Infusion Rate 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 Time WARNING NOT FOR CLINICAL USE ON HUMANS Doc: 1200-02 . Rev. 11 V3.
www.nextadvance.com NEXT>>>ADVANCE SP300 Programmable Syringe Pump Quick Start Instructions Plug in the pump. Press the power switch to turn on power. Press any key to stop the display from blinking. Setup Pumping Parameters To Change Numbers: Use the arrow keys to increment individual digits. To move the decimal point: Press and hold the left-most arrow key for at least 1 second. When the digit increments from 9 to 0, the decimal point will begin to shift.
NEXT>>>ADVANCE www.nextadvance.com SP300 Programmable Syringe Pump Table of Contents 1. GENERAL INFORMATION AND PACKING LIST ................................................... 1 1.1 1.2 2. WARNINGS ! AND CAUTIONS ! .............................................................................. 1 DISCLAIMER AND WARRANTY ....................................................................................... 1 OVERVIEW ......................................................................................
NEXT>>>ADVANCE www.nextadvance.com SP300 Programmable Syringe Pump 1. General Information and Packing List Thank you for purchasing the Model SP300 “Just Infusion”™ Syringe Pump. With the SP300 syringe pump you will be able digitally set an infusion rate for steady pumping. Please familiarize yourself with the SP300’s operation by reading this user's manual. For future reference, record the serial number, located on the rear of the pump, and the date of purchase. Next Advance Inc.
NEXT>>>ADVANCE www.nextadvance.com SP300 Programmable Syringe Pump Warranty Next Advance Inc. warranties this product and accessories for a period of two year, parts and labor, from the date of purchase. The repaired unit will be covered for the period of the remainder of the original warranty or 90 days, whichever is greater. A return authorization number must be obtained from Next Advance Inc. before returning a unit for repair.
www.nextadvance.com NEXT>>>ADVANCE SP300 Programmable Syringe Pump operation of the SP300 will become quite intuitive. Every effort has been made to design the SP300 with a consistent and intuitive user interface.
NEXT>>>ADVANCE 5: www.nextadvance.com SP300 Programmable Syringe Pump Then press the white drive-nut button and slide the pusher block against the syringe plunger. Release the white drive-nut button. To unload the syringe, reverse the instructions for syringe loading. 5.
NEXT>>>ADVANCE www.nextadvance.com LED Description mm Millimeters ml Milliliters min Minutes l Microliters hr Hours Withdraw Pumping Direction: Lit: Withdraw Purge Pumping Dispensed Displayed volume is dispensed volume Pumping Lit: Not lit: SP300 Programmable Syringe Pump Pumping rate units are expressed using 2 LEDs: ‘ml/min’ = ‘ml/hr’ = ‘l/min’ = Motor is operating The Pump is stopped ‘l/hr’ = ml min l hr ml min l hr ml min l hr ml min l hr 5.
NEXT>>>ADVANCE www.nextadvance.com SP300 Programmable Syringe Pump when a non-arrow key is pressed. The new pumping rate is stored in memory. See section 9.5, “Syringe Diameters and Rate Limits”, for a list of minimum and maximum pumping rates. A pumping rate of 0.0 will stop the pump. When the pumping rate is changed, if it is out of range of the . Pressing any key clears the message and returns pumping rate limits, the display will show to the previous pumping rate. 5.6.
www.nextadvance.com NEXT>>>ADVANCE SP300 Programmable Syringe Pump diameter. Any new parameter value will take affect immediately upon being stored. 5.11 Special Power-Up Functions The following special functions are accessed by pressing the relevant key, while turning on power to the pump. 5.11.1 Firmware Version Display To display the pump’s firmware version, press the left-most up arrow key (/) while turning on , or similar. Pressing any key will clear the power to the pump.
NEXT>>>ADVANCE www.nextadvance.com SP300 Programmable Syringe Pump Changing Volume Units The volume units used for the accumulated volume can be changed to either ‘ml’ or ‘l’. NOTE: Volume units can only be changed immediately after setting the syringe diameter and before the pump is started. After the syringe diameter is entered, display the “Volume Dispensed” by pressing the “Volume” key. The current volume units and the “Dispensed” LED will be lit. and the current volume units will blink.
NEXT>>>ADVANCE www.nextadvance.com SP300 Programmable Syringe Pump 7. Setup Configuration: Set Power Failure Mode To change or view the setup configuration, the Pump must be stopped. Press and hold the ‘Diameter’/‘Setup’ key until the parameter, ‘PF’ is displayed. After 2 seconds, or when any non-arrow key is pressed, the next parameter will be displayed . (See sec. 5.10, ‘Setup’ Key). Pressing an arrow key under a value will change the parameter. The following will be displayed: n Power Failure Mode.
NEXT>>>ADVANCE www.nextadvance.com SP300 Programmable Syringe Pump 9.2 Troubleshooting and Maintenance Maintenance: Periodically, a small amount of all-purpose oil should be applied to the guide rods. The mechanism should be kept clean to prevent impeded operation. No other special maintenance or calibrations are needed Pusher block makes a snap or click sound when the pump is started: This is a normal condition.
NEXT>>>ADVANCE www.nextadvance.com SP300 Programmable Syringe Pump 9.5 Syringe Diameters and Rate Limits Next Advance www.nextadvance.com Model: SP300 syringe pump Maximum and minimum flow rates Syringe (cc) Inside Diameter (mm) Maximum Rate (mL/hr) Minimum Rate (µl/hr) Maximum Rate (mL/min) B-D 1 3 5 10 20 30 60 4.699 8.585 11.99 14.43 19.05 21.59 26.59 39.27 131 255.6 370.3 645.4 829 1257 0.73 2.434 4.748 6.876 11.99 15.4 23.35 0.6545 2.184 4.261 6.172 10.75 13.81 20.
