User Guide

4. After logging in for the first time, the web
interface automatically redirects to the System >
Administration > User Manager page and
forces you to change the default password for
each account. (FIGURE F)
NOTE: Remember the password(s) for future
reference.
6. Use the remainder of this guide to change the
device name and IP address as desired.
FIGURE F
The web interface login appears.
3. Log into the web interface
with the following default
administrative credentials:
NOTE: The default names and
passwords for the
Administrator, Device
Manager, and Read Only User
accounts in your web interface
respectively, are as shown.
Read Only User
Username: user
Password: password
Device Manager
Username: device
Password: password
Administrator
Username: admin
Password: admin
Understanding Network UPS Access
(Continued)
Use the following steps to view the IP address from
the LCD display menu.
NOTE: The service mode password is 0000 and is
automatically entered on the LCD. Press Select to
verify each password character and enter the
menu.
5. Scroll and highlight the Sleep Mode service
mode menu option, and press Select.
6. Scroll and highlight the Disabled option, and
press Select.
7. Press the Cancel button to exit.
3. Click OK.
For more information, refer to the NEXSYS UPS
RackLink™ Network Card User Manual (100-00074)
at www.legrandav.com.
Configuring a Workstation Static IP
Connected Directly to the Network Card or via Switch
(Continued)
Locating the Card on Your Network
Using DHCP and the Device Discovery Tool (Continued)
Locating the Card on Your Network
Using DHCP and the Device Discovery Tool
Directly connect your workstation to the network
card’s Ethernet port using a straight through RJ45
(Cat-5 or better) Ethernet cable (not provided) and
configure your workstation with a static IP address
on the same network as follows.
1. In Windows™, go to Control Panel > Network
and Sharing Center > Ethernet Properties >
Internet Protocol Version 4 (TCP/IPv4)
Properties.
Configuring a Workstation Static IP
Connected Directly to the Network Card or via Switch
Accessing Your IP Address on the LCD
Menu
Accessing Your IP Address on the LCD Menu
(Continued)
Default Administrative Account Settings
The network card has
the following default
IP address, DHCP
setting, and admin
account credentials.
If desired, leave the default DHCP as enabled,
connect your workstation to the network card Ethernet
port using a straight through RJ45 (Cat-5 or better)
Ethernet cable (not provided).
Then, you may find the current IP address using
the LCD menu (see page 11) or using the RackLink
Device Discovery tool and change the device name
or IP address as desired.
For more information, refer to the NEXSYS UPS
RackLink™ Network Card User Manual
(100-00074) at www.legrandav.com.
Download the Device Discovery tool at
https://www.legrandav.com/resources/power-downloads .
IP Address: 192.168.1.201
DHCP: Enabled
Admin Username: admin
Admin Password: admin
1. If your UPS isn’t already on, press the power
button on the front panel and hold it until you
hear a single beep, and then release.
For more information, refer to “Understanding
the UPS Power Button” in the NEXSYS Line
Interactive UPS User Manual (100-00072) at
www.legrandav.com.
2. Press the Select button to enter the Main
Menu.
3. Use Up and Down buttons to scroll
and highlight the Information menu option and
then press Select.
4. Use Up and Down buttons to scroll
and highlight the IP Address menu option, and
then press Select.
The IP address appears.
5. Write down the IP address for reference.
1. Enter the IP address in the
URL field of your preferred
web browser and press
Enter.
Changing the Device Name and IP Address
Using the Network Card Web Interface
IP Address:
192.168.1.201
Changing the Device Name and IP Address
Using the Network Card Web Interface (Continued)
Changing the Device Name and IP Address
Using the Network Card Web Interface (Continued)
Changing the Device Name and IP Address
Using the Network Card Web Interface (Continued)
Click
Advanced
the security certificate warning (since locally
issued certificates are used at this point).
(FIGURE E)
FIGURE E
Click Proceed
2. Click Advanced and then Proceed to bypass
FIGURE D
NOTE: Refer to
documentation
provided with your
workstation to access
the equivalent IPv4
properties screen.
2. Select the Use the
following IP
address radio
button option and
provide the values
as shown.
(FIGURE D)
Changing the Device Name and IP Address
Using the Network Card Web Interface (Continued)
Contacting Middle Atlantic Canada
P: [phone] | F: [phone]
ca.middleatlantic.com | [e-mail]
United States (US)
Legrand | AV Headquarters
6436 City West Parkway
Eden Prairie, MN, 55344, USA
At Legrand AV Inc. we are always
listening. Your comments are welcome.
Legrand AV is an ISO 9001 and ISO
14001 Registered Company.
FIGURE H
Warranty
For warranty information,
refer to www.legrandav.com/policies/warranty_information.
Contacting Corporate Headquarters
P: [phone] | F: [phone]
www.legrandav.com | [e-mail]
• Access the System > Administration > TCP/IP
page, change the IP address as desired and
click Submit. (FIGURE H)
FIGURE G
• Use the navigation menus on the left to access
the Device > Management > Configure page
change the Device Name as desired and click
Submit. (FIGURE G)
NOTE: We recommend
changing the device name
on each unit for easier
in-person and remote identification purposes.
As shown above, the device name is shown when
correctly accessed from the Discovery tool.
The following naming convention provides an
example for easy identification by device, enclosure,
and location.
5. Provide a secure
password for each account
and click Submit.
Specific Enclosure
UPX-RACK5-NY
Device
Location
Page 12
Page 15Page 14
Page 11Page 10
Page 13 Page 16
Page 9