UltraEasy Fence UH66/FN0213R Installation Guide-In the Concrete v20230108US
CONTENTS Important Note 3-4 UltraEasy Fence Parts 5-7 Framing Layout for the UltraEasy Fence 8 UltraEasy Fence Installation Installation Procedure - In the concrete -Post Mount Installation 9 - 11 -Post Sleeve Installation 11 -Fence Board Installation 12 - 16 UltraEasy Fence UH66/FN0213R Installation Guide-In the Concrete / v20230108US 2
IMPORTANT: Read All Sections Before You Start For the most up-to-date information, please visit our website @ www.newtechwood.com Prior to installing any composite product, it is recommended that you check with local building codes for any special requirements or restrictions. The diagrams and instructions outlined in this guide are for illustration purposes only and are not meant or implied to replace a licensed professional.
Ventilation UltraEasy fencing needs to have at least one of the clips or stopper installed at the bottom of each aluminum post sleeve as well as a starting and ending aluminum trim to work properly. If one clip or stopper is not installed at the bottom of the post sleeve, there will be not sufficient enough air flow and could result in high wind speeds damaging the fence.
UltraEasy Fence Parts ' * ( ) - , + .
)UJK 7Z_ *KYIXOVZOUT 6GXZY 4[SHKX ' ^ )ROV ,4 ( ^ 9IXK] 9: ^ SS =0 ) ^ 6UYZ )GV ,4 8 * ^ +TJOTM 'R[SOT[S :XOS ,4 + ^ 6UYZ :XOS ,4 , ^ -GR\GTO`KJ 9ZKKR :[HK - ^ ,KTIK (UGXJ ;. . ^ 6UYZ 9RKK\K ,4 8 / ^ 6UYZ 3U[TZ ,4 0 ^ 9ZUVVKX
)UJK 7Z_ *KYIXOVZOUT 6GXZY 4[SHKX 3 ^ 9ZGOTRKYY 9ZKKR 9;9 =0 :NXKGJ 8UJ 3 ^ SS 4 ^ 9ZGOTRKYY 9ZKKR 9;9 =0 ,RGZ =GYNKX 3 5 ^ 9ZGOTRKYY 9ZKKR 9;9 =0 4_RUT 2UIQ 4[Z 3 6 4UZ )NKSOIGR 'TINUX OTIR[JKJ Please Note: When choosing which chemical anchor to use, always check first with your local home centers and hardware stores to see which type of chemical anchor is appropriate to apply with your concrete ground.
Framing Layout for the UltraEasy Fence 1. Straight Line 3. T-intersection 2. Right-Angle Corner 4.
UltraEasy Fence Installation A.
2 Install the Thread Rod (M) according to the below work procedures, as shown in Diagram 2-1. 1. Use an electric hammer drill to drill the thread rod holes on the ground. 2. Blow out the dust from the hole using a blow pump or oil free compressed air. 3. Clean the hole using a stiff nylon brush. 4. Clean the hole again using a blow pump or vacuum cleaner. Make sure all particles, dust are all completely removed. 5.
When the Chemical Anchoring (P) material reaches the cure time, put the Post Mount (I) in place, as shown in Diagram 2-2 , and secure it with the Lock Nut (O) as shown in Diagram 2-3 . Post Sleeves Installation 3 Insert the Post Sleeves (H1) over the Post Mounts (I), as shown in Diagram 3 . Please Note: Check whether the Post Sleeves (H1) is appropriately placed with the Post Mounts (I), as shown in Detail 3-1. / 6UYZ 3U[TZ . 6UYZ 9RKK\K 5 2UIQ 4[Z 4 ,RGZ =GYNKX 3 :NXKGJ XUJ Diagram 2-2 / 6U
Fence Boards Installation 5 Put the Starting Aluminum Trim (L) over 4 Insert a Stopper (J) into the bottom of the Post Sleeves (H1) and fix it with the Screw (K), as shown in Diagram 4 . the Stopper (J), as shown in Diagram 5 and Detail 5-1 . Please Note: Ensure the Stopper (J) is placed at the bottom of the Post Sleeves (H) properly. . 6UYZ 9RKK\K . 6UYZ 9RKK\K 0 9ZUVVKX 1 9IXK] *KZGOR 2 9ZGXZOTM 'R[SOT[S :XOS Diagram 4 Diagram 5 . 6UYZ 9RKK\K 2 9ZGXZOTM 'R[SOT[S :XOS / 6U
6 Insert a Galvanized Steel Tube (F) into the central hollow of the 3rd, 6th, 9th and 12th Fence Board (G), as shown in Diagram 6 and Detail 6-1 . ,KTIK (UGXJ , -GR\GTO`KJ 9ZKKR :[HK 7 Put the first Fence Board (G) over the Starting Aluminum Trim (L), as shown in Diagram 7 . . 6UYZ 9RKK\K Diagram 6 * +TJOTM 'R[SOT[S :XOS 2 9ZGXZOTM 'R[SOT[S :XOS ,KTIK (UGXJ Diagram 7 8 Complete the installation for the rest of the Fence Boards (G), as shown in Diagram 8 . -GR\GTO`
9 Insert the Post Trim (E) into the Post Sleeve (H1), as shown in Diagram 9 . 11 Put the Ending Aluminum Trim (D) over the last Fence Board (G), as shown in Diagram 11 and Detail 11-1. * +TJOTM 'R[SOT[S :XOS + 6UYZ :XOS *KZGOR . 6UYZ 9RKK\K Diagram 9 10 P u t t h e C l i p (A) i n s i d e t h e E n d i n g Aluminum Trim (D) and fix it with the Screw (B), as shown in Diagram 10 . * +TJOTM 'R[SOT[S :XOS Diagram 11 ' )ROV * +TJOTM 'R[SOT[S :XOS ' )ROV ( 9IXK] . 6UYZ 9RKK\K Detail 11
12 Cut a small piece of Post Trim (E) and put it over the Ending Aluminum Trim (D) to cover the slot between the Post Sleeve's (H1) top and the Ending Aluminum Trim (D), as shown in Diagram 12 and Detail 12-1. + 6UYZ :XOS *KZGOR Diagram 12 + 6UYZ :XOS * +TJOTM 'R[SOT[S :XOS ,KTIK (UGXJ . 6UYZ 9RKK\K Detail 12-1 UltraEasy Fence UH66/FN0213R Installation Guide-In the Concrete / v20230108US 15
13 Put the Post Cap (C) on the top of the Post Sleeve (H1), as shown in Diagram 13 . 14 Diagram 14 presents the final appearance after complete the installation. ) 6UYZ )GV . 6UYZ 9RKK\K Diagram 14 Diagram 13 UltraEasy Fence UH66/FN0213R Installation Guide-In the Concrete/ v20230108US 16
UltraEasy Fence UH66 / FN0213R Installation Guide-In the Concrete v20230108US ©2023 Newtechwood Corporation NewTechWood® is a registered trademark of Newtechwood Corporation. To obtain a copy of the most current version of this installation guide, visit us online at www.newtechwood.com.
