Wireless-N Broadband AP / Router Quick Installation Guide Version 1.
Table of Contents English 1. Before Installation .............................................................................................................................2 2. Hardware Installation ........................................................................................................................3 3. Configure your computer’s TCP/IP Settings......................................................................................4 4. Configure your AP ....................................
1. Before Installation Thank you for purchasing the Wireless 11n AP Router. This guide will help you set-up and configure your AP with easy-to-follow instructions. For more detailed or advanced settings, please refer to the User Manual on the CD-ROM. Package Contents Please make sure you have the following in the box: ♦ ♦ ♦ ♦ ♦ ♦ ♦ WRTR-501 Wireless-N Broadband AP Router Multi-Language Quick Installation Guide User Manual CD-ROM Three dipole 2dBi RSMA detachable Antennas AC/DC Power Adapter RJ-45 Cat.
2. Hardware Installation 1. Power off your network devices. 2. Locate an optimum location for the AP. The best place for the AP is usually at the center of your wireless network, with line of sight to all of your wireless devices. 3. Adjust the antennas. Normally, higher location of your AP may get better performance. 4. Using a standard Ethernet network cable, connect to the AP’s Ethernet port to your local network. 5. Connect the AC power adapter to the AP's Power port.
3. Configure your computer’s TCP/IP Settings Windows 2000/XP 1. 2. 3. Click Start; click Settings and then click on the Control Panel. Double-Click the Network Connection icon. Right-Click on the Local Area Connection icon and then click on Properties. The Local Area Connection Properties windows will appear. 4. Under the General Configuration Tab, locate and select TCP/IP with the corresponding network card, then click Properties. The Internet Protocol (TCP/IP) Properties window will appear.
. Now your computer is ready to access and configure the AP. Windows VISTA 1. Click Start Æ Control Panel, then Network and Internet Æ Manage network connections. 2. Right-Click on the Local Area Connection icon and then click on Properties. The Local Area Connection Properties windows will appear. 3. Under the Networking Configuration Tab, locate and select Internet Protocol Version4 (TCP/IPv4) with the corresponding network card, then click Properties.
4. 5. Click on Use the following IP Address and enter IP Address: 192.168.1.10 Subnet Mask: 255.255.255.0 Default gateway: 192.168.1.1 Now your computer is ready to access and configure the AP. NOTE : The default IP address setting for the AP is a class C IP address (192.168.1.1 / 255.255.255.0). Please make sure that the current workstation is following the class C IP address range, from 192.168.1.2 to 192.168.1.
4. Configure your AP 1. 2. Open your web browser, type http://192.168.1.1 in the Address bar, and press Enter. An authentication window will appear. Enter the username and password, and then click OK. By default, please leave blank in username and type admin in password. 3. Turn to the Wireless Section; here you may select a different channel, SSID or enable Security if it is necessary. 4. Click “Save Settings” button to finish the Setup if you have something change.
5. When the AP reboot procedure is completed, you may change the TCP/IP properties of this computer. Select the “Obtain an IP address automatically” instead of “Use the following IP Address “ item if your local network has DHCP server service to assign IP address for your wireless client. This step will set your computer as DHCP client and get IP from your DHCP server via AP. If there is no DHCP server in your network, then you should assign one proper IP address manually to fit your network IP subnet. 6.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
