PLEASE READ AND SAVE THESE INSTRUCTIONS NewAir AC-10100E / AC-10100H Portable Air Conditioner Owner’s Manual
ELECTRICAL SAFETY • This appliance is for indoor use only. • Always turn off the unit and unplug it when not in use. • Do not use this unit in excessively humid or wet environments. • Do not pull or place strain on the power cord when moving the appliance. • IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY AN ELECTRICIAN OR SPECIALIZED TECHNICIAN AUTHORIZED BY THE MANUFACTURER IN ORDER TO PREVENT FIRE. FOR MAXIMUM EFFICENCY • Do not exceed the recommended room size.
PARTS 1. Control panel 2. Air outlet 3. Carrying handle 4. Caster 5. Cord storage 6. Air filter 7. Air inlet 8. Exhaust air outlet 9. Air inlet 10. Rubber plug/ drainage point 11. Hose adaptor (goes over the hose and into the window kit) 12. Exhaust hose 13. Extendable window kit 14. Active carbon filter 15. Drain tube for continuous drainage 16.
INSTALLATION Extendable window kit 1. Open the window and insert the window kit into the open gap. 2. Close the window until the window kit is held securely. You may need to adjust the size of the window kit and secure it with screws. This technique may also be used for sash windows. 3. Fit the exhaust hose into the exhaust air outlet located on the back of the air conditioner. 4. Attach one end of the hose adapter onto the exhaust hose. 5. Attach the other end of the hose adapter to the window kit.
Mounting of the Exhaust Pipe • Only use the hose provided and clip exhaust hose to the back of the air conditioner. • Avoid kinks and bends in the exhaust hose. This can cause moist air to accumulate, causing the unit to overheat and shut down. • The exhaust hose may be extended from 12 inches (300mm) to 59 inches (1500mm), but for maximum cooling efficiency use the shortest length possible. WARNING! The included exhaust hose is specifically designed to fit the specifications of this unit.
Installation of the Carbon Filter 1. Remove the filter frame from the unit. 2. Separate the filter fixer from the filter frame. 3. Remove the activated carbon filter from its plastic bag. 4. Attach the activated carbon filter to the filter frame. 5. Reattach the filter fixer onto the filter frame (the activated carbon filter should be placed between the filter frame and filter fixer firmly). 6.
OPERATION Control panel 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Automatic mode indicator Cooling mode indicator Fan (ventilation) mode indicator Mode selection button Timer operation indicator Timer button Full water tank indicator Temperature increase button Display window Remote control receiver 11. 12. 13. 14. 15. 16. 17. 18.
Setting the Model/Function: Press the MODE button to select the desired mode (cooling, fan or heating). Setting Temperature 1. 2. 3. Press 'Temperature up' or 'Temperature down' button to change the set temperature. The display window will indicate the set temperature. If not, the temperature displayed will show the ambient room temperature. Please note that the preset temperatures are as follows: o o Cooling: 75 F (24 C) o o Heating: 68 F (20 C) Setting Fan/Ventilation Speed: 1.
Heating Function (For AC-10100H Only) 1. When the air conditioner is in heating mode, ambient warm air is recycled and used to heat your immediate area. The exhaust pipe will still need to be fitted onto the unit in order for the cold air to be removed. 2. Continuous drain is compulsory while the unit is in heat mode. Working range for heating o o function is 45 to 77 F (7 ~ 25 C). If the ambient temperature is lower than this range, the unit may not work properly.
DRAINING THE UNIT During the cooling process, some water will be extracted from the air and stored within the unit’s water reservoir. If the reservoir is full, both the compressor and motor will stop and the unit will beep (press any button to stop the beeping sound). The full water tank indicator light will also start flashing. To resume cooling, empty the reservoir by following these steps: 1. Turn off the air conditioner and unplug it from the wall socket.
• The drain tube may be extended by adding an extension tube with a suitable connector. Drain tube Please Note: 1. The drain must be at or below the level Original drain tube of the drainage port. 2. The full water tank indicator light will not work when the unit is being continuously drained. Extension tube (OD: 0.7”) 3. To extend the drain tube, you can connect it with another hose with an overall diameter of approximately 0.7” (18mm).
MAINTENANCE INSTRUCTIONS Always unplug the air conditioner from the power supply before cleaning. To maximize the efficiency of the air conditioner, regularly clean the unit. Cleaning the Housing: • Use a soft, damp cloth to wipe the body clean. • Never use aggressive chemicals, gasoline, detergents, chemically treated cloths, or other cleansing solutions. These all could possibly damage the cabinet.
FAULT CHECK LIST The air conditioner does not run. Ÿ Ÿ Ÿ Ÿ The unit does not produce enough Ÿ cooling. Ÿ Ÿ Ÿ Is the air conditioner plugged in? Is the power outlet functioning correctly? Is the full water tank indicator light flashing? Is the ambient room temperature lower than the set temperature? Is the unit placed in direct sunlight? If so, close any curtains or move the unit to a more shaded area.
13 TECHNICAL SPECIFICATIONS Model Number AC-10100E AC-10100H Power Consumption (Cooling) 909W / 8.3A 909W / 8.3A Power Consumption (Heating) N/A 909W / 8.3A 3 Air Volume (Max. Speed) 218CFM (355m /h) Dehumidification Capacity 2.11 pints/hour Power Supply 115V, 60Hz Compressor Type Rotary Refrigerant R-410A (Please refer to the rating label) Fan Speeds 2 Timer Exhaust Pipe 1~12 hours Ø 5” x 59.06 “ (Ø 127 x 1500mm) Net Weight Dimensions (W x D x H) 48.5 lbs (22 kg) 12.1” x 15.
LIMITED MANUFACTURER’S WARRANTY This appliance is covered by a limited manufacturer’s warranty. For one year from the original date of purchase, the manufacturer will repair or replace any parts of this appliance that prove to be defective in materials and workmanship, provided the appliance has been used under normal operating conditions as intended by the manufacturer.
