Datasheet

Slide the boot onto the cable.

Terminate RJ45 connector on the cable.

See following pages.

Press the locking latch of the RJ45 and place

the two adapters onto the RJ45.

Put chuck onto the cable.

Slide RJ45 and chuck together into the housing.

Finish the assembly by turning the bushing

onto the connector. Screw bushing fully up to

the end.

onductors with an

insulation. O.D. 0.037” / 0.95 mm to 0.047” / 1.07 mm.

Jacket: O.D. 0.22” / 5.5 mm to 0.25” / 6.5 mm

Pay attention: Hold the brackets together.

Pay attention to the plug latch which has to be on

the opposite side of the key.

Attention: Pay attention to the guiding key.

Suitable cables:

AWG 22 to 28 soldid or stranded c

Key

Draft. Nr.: BDA 194 / 3102M1581 Update: 17.08.2011

I I

www.neutrik.com

ASSEMBLY INSTRUCTION

NE8MC6 etherCON Cable Connector CAT 6

NEUTRIK AG LI T: +423 / 237 24 24 F: +423 / 232 53 93

NEUTRIK USA Inc. USA T: +1 732 / 901 9488 F: +1 732 / 901 9608

( )

NEUTRIK UK Ltd. UK T: +44 1983 / 811 441 F: +44 1983 / 811 439

NEUTRIK Vertriebs GmbH DE / NL / AT/DK T: +49 8131 / 280 890 F: +49 8131 / 280 830

NEUTRIK France FR T: +33 1 / 4131 6750 F: +33 1 / 4131 0511

NEUTRIK Tokyo Ltd. JP T: +81 3 / 3663 4733 F: +81 3 / 3663 4796

NEUTRIK Hong Kong Ltd. HK T: +852 / 2687 6055 F: +852 / 2687 6052

PAGE 1
R ASSEMBLY INSTRUCTION NE8MC6 | etherCON Cable Connector CAT 6 A A Slide the boot onto the cable. B Terminate RJ45 connector on the cable. See following pages. C Press the locking latch of the RJ45 and place the two adapters onto the RJ45. Pay attention: Hold the brackets together. B D Put chuck onto the cable. Attention: Pay attention to the guiding key. E Slide RJ45 and chuck together into the housing. C Pay attention to the plug latch which has to be on the opposite side of the key.
PAGE 2
R ASSEMBLY INSTRUCTION B I etherCON CAT 6 Terminate RJ45 connector on the cable. 1 2 3 4 5 6 7 8 1 White-Green Green White-Orange Blue White-Blue Orange White-Brown Brown Consider cable end termination usually straight thru cable acc. TIA 568A. Assembly of wire, load bar and plug. 2 Strip outer jacket 20 mm long. 3 Separate pairs in bundles. 4 Straighten and separate into individual leads. 5 Organize leads into proper order and trim edge to be even.
PAGE 3
R ASSEMBLY INSTRUCTION I etherCON CAT 6 7 Insert Load Bar and load Wires into open end. 8 Slide Load Bar into position against Jacket. 9 Trim leads so Jacket is 8.64 mm / 0.34” from edge. 8.64 mm [0.34”] 10 Inser Wires and Load Bar into Plug and push ful forward. Terminate Plug with Hand Terminator MOLEX #622020500 or any other suitable crimp tool. 11 In the case of using shielded cable crimp shield to connector. BDA 194 I 17.08.