E V I T A V O N IN S N O I T U L SO O R P D O I 2 A N Da o t O / I /EBU S E A ine, Mic, L Interf ® e t n ace
E V I T A V O N S IN N O I T U L SO E DANT ® Y N erCO CONDAR h t e 2 x ARY/SE PRIM RACKNTABLE MOU ED RUGG ING S U O H , AES L I N EP UT OUT ES A , E N LI MIC, T INPU
NA2-IO-DPRO Mic, Line, AES/EBU I/O to Dante® Interface Connect even more legacy audio equipment to your Dante® network • • • • • • Connect analog audio equipment to a Dante® network Heavy duty adapter for rugged stage conditions Lockable audio and network connections Connect up to two analog line or mic signals to a Dante® network Connect AES/EBU signals to a Dante® network and provide an AES/EBU signal from the Dante® network Switched mode to daisy chain devices • • • • • • Feed non Dante® ready am
Y T I L A N O I Y T T I C L FUN FLEXIBI AND OVERVIEW FRONT HPF/Pad System Ready Phantom power 48V Signal Present Output MUTE Input type – Analog / AES Output type – Analog / AES Balanced XLR Input: Input 1 Analog only Balanced XLR Output: Output 2 Analog/AES Balanced XLR Input: Input 2 Analog/AES Balanced XLR Output: Output 1 Analog only If AES is used, CH1 becomes inactive OVERVIEW REAR Link (Ethernet connection established) Reset Button etherCON® chassis for Primary Dante® Interface/PoE
REDUNDANT MODE SECONDARY PRIMARY Dante ready mixing desk PoE Injector with NO class DPRO PoE Injector with NO class Switch with NO PoE support SECONDARY Switch with NO PoE support PRIMARY AES or Audio connection Network connection SWITCHED MODE SECONDARY/ FEEDTHROUGH DPRO PRIMARY Analog mixing desk SECONDARY DPRO Audio connection Network connection AES DPRO NA2-IO-DPRO Dante ready mixing desk PRIMARY Only PoE injector without a class to be used for daisy-chaining.
HOW TO SET IT UP? 1 Connect the audio lines as required (e.g. audio source to the MIC IN channels; AES/EBU to AES/EBU channels and audio destination to the LINE OUT; AES/EBU channels) 2 Next, enable the Dante and power connection via the etherCON® chassis connector. Connect the NA2-IO-DPRO to an Ethernet switch which supports PoE. If PoE is not supported by the switch in use, deploy an external midspan PoE power injector. For Daisy-Chaining (Switched mode) use only a PoE injector with no classification.
L A C I N H TEC A T A D GENERAL SPECIFICATIONS Channel Supported sampling rates 2 INPUT (Line, Mic, AES/EBU) Bit depth 16, 24 and 32 bit 2 OUTPUT (Line Level, AES/EBU) Latency based on user selection; min. 0,25 ms (Dante®) 44.1 / 48 / 88.2 / 96 kHz Ethernet connection 1.000 BASE-T (supporting PoE) < 6 Watt Power supply PoE (Power over Ethernet) switch or ELECTRICAL DATA Power consumption PoE midspan power injector (according to IEEE 802.
ERS) UART EADQ H ( 43, T E IN .com Riet 1 TENS neutrik L IE C H G, Im alten tein utrik@ e n , s 3 A ik hten 53 9 Neutr n, Liec +423 232 Schaa 4, F 2 9494 4 2 3 237 T +42 oad, reek R gart C g a T 115 USA Inc., 4 28208 m ik USA h Carolina, eutrikusa.co Neutr rt n o @ N IA , fo e in tt , USTR Charlo 972 30 50 RK / A 04 N M A e 1, 7 E 1 D / + S T s L A N D ankel-Stras THER Felix-W Y / NE , N H A b G E R M ertriebs Gm y an trik.
